Great work! Specially how you stuck to resolving the design issue so you make it work with that particular motor. I had doubt about that motor strength when you posted that project earlier, I'm glad and amazed how you make it work. Keep up a good work, I hope you have more projects like this to share.

No se que es lo mejordel video, si el dispenser de alimento o el mate!! Saludos desde Argentina

Hello Sebastian, my name is Miguel Avello from the US I recently discovered your channel and am truly impressed by the quality and ingenuity of your projects. Your approach to electronics, especially in the way you share your knowledge, is remarkable. You not only provide videos but also share all content in a structured and clear manner, which showcases your technical skills as well as your creativity and attention to detail. The way you make complex concepts easily understandable is truly commendable. As someone who shares a passion for Smart Home Automation and DIY projects, I find your content both informative and inspiring. Your project on [specific project] particularly resonated with me, as it closely aligns with my interests in building sensors and integrating them into home automation systems. Keep up the fantastic work! Your channel is a treasure trove for anyone passionate about electronics and DIY projects. I am eagerly looking forward to your future videos! Best regards, Miguel PS: I sent you a small donation for you great work and for the way you share all your knowledge.

Really nice project, well done! Great you took the time to write everything out and shared the source + designs 👍🏻

Very cool, I'd love to see a addon to this project: a food bowl attachment with a lid that only opens when the right cat (RFID chip) is near. That allows cats on a diet to get their portion (or special food) and the other cat(s) to get it's own "normal" food.

Great idea, love how you implement easy accessible for cleaning. You got my like. I might even rebuild this

Thank you for sharing this awesome project! We are waiting for the next one :)

Criminally underrated channel.

Rewelacja! Gratuluję pomysłu oraz super wykonania. Zostaję na dłużej! :)

Beautiful printed circuit assembly sir!

Awesome project dude! Thanks for sharing! 👌

Best video I've seen and very informative!! Also impressive chip!

Awesome video. I was looking to see how I can do an auto feeder for my fish tank. Suppose it's the same concept just a bit smaller. I think you should add on a level sensor to check how much food is in the container, then HA will tell you to top-up. Great work

amazing, and with attention to details

Piękna robota!

THANK YOU BRO !

Thanks for the files!

Well done ! Really nice design ! I think I will use it and add a BLE beacon detection to filter out cats :)

Super cool, as always =) Next project idea: Build an ESP Chip dispenser for makers ;-)

Great project and nicely done.. :D About the coding part, I don't find it boring, and people can just fast forward when that parts come if they don't like it. But maybe it could help if there were some confusion on where to put code, just a thought.. :)

This is cool. I am needing something like this. Although I would need to build 4.

excelente !!! tambien me gusto el mate ..

No podía faltar el mate jajaja, great job!

aguante ese mate ! buen proyecto exitos

that's amazing

Great project ! Definately subscribing , hope to see some Raspberry Pies in following projects as well :)

Świetny projekt, aż dziwne że dopiero dziś trafiłem na Twój profil

good job!

So cool! You are so smart!. Would love a video on how to design pcb:s. Also waiting for you to create a poe doorbell :)

Very nice💪💪💪

Nice job. My cat said "meow, I want one too"

Thanks!

My dog have much bigger dry food. I wonder if it will work with that. But still, one of the DIY pet feeder I've seen so far!

Hi there. Awesome project. I had a doubt. Is there food stored in there protected from atmosphere? If its not an air tight container, won't it affect the quality of food?

Great video, Why not use a time-scheduled-based feeding ?

Hi so basically if i just wanna use the simple board on this project without PCB do you have some schematic i can follow, it means a lot to me, thank you !

Awesome project! I'm going to iterate on your design a bit and try to as RFID and a food cover. Fat cat issues

Drinking mate?! Niiiiiice

Thanks for sharing the details. I had lots of issues with an auger based pet feeder in the past, have you really prevented the jamming problem?

Hi Sebastian! Nice project, thanks for sharing and I'll try to do this one for a friend. By the way, are you drinking mate at the end of the video? Cheers from Argentina :)

Hello! I made two of these for my cats, everything running, but I can't find a method for the device to release around the same amount of food everytime, sometimes I run the cycle to drop around 15 grams of food, one of the machines drops fine, the other almost nothing, and this can repeat on the other one. Also, one of the cats could just touch the feeder with his paw and some pieces of food would drop, and he can keep doing that for quite some time. Any suggestion is more than welcome.

Great video. I was thinking to make a similar project with an arduino nano but now I think the microprocessor you used fits better tonthe task. How much time did this project take you from start to finish?

Super cool!! Would love to see more. (Also, there was a time or two the music was a bit too loud over your voice.)

Hi Sebastian:) Can you help me, how to manage the PCB order at JLC PCB ? I can figure out to upload the Gerber files, but I have a problem with the BOM part. The BOM file you added is a PDF document. Would you be able to make an excel file that is capable of to be handled at JLC PCB? Or is it possible to get the seller you link to at aliexpress send only the parts for this board (it seems it gonna be tooo expensive), because many of the items is sold I 10 pieces or more.

hi, i’m just new to this field and i intend to do this project. I have a question that I already bought step motor and mtiny esp8266, do I need to buy an Adruino Uno,tks guys.

Hello Sir. Your cat feeder is extremely amazing and useful. I am impressed. I have a question. Is it possible to program this to be used with a home assistant like Alexa or google home? Thanks!

Where can I buy this? You should produce and sell it online! Very cool

Do you ship to Nigeria?

I just printed the design and it s jamming with big kibble. They're stuck at the front between gear and front internal slope😢

I just ordered the parts for it, just needed a stepper

is it possible to schedule dispensing instead the need to press the button at the app?

Hi, will this work with any Nema17 stepper motor? 🤔

Do you have a lot or woild.you sell your documentation for DIYer to build one?

Hej, kończyłeś Elektronike i Telekomunikacje czy inny typ studiów elektronicznych?

Here in my region it is very common for ants to appear, does this project have a fence between the food and the exit? Or can the ant climb up and reach the food?

Treemendo! Pero... QUE ONDA CON EL MATE? de donde sos?

I'd like to put one of these out in my field for the feral cats. What kind of solar power supply would be needed?

Hi Sokol, Can I control in when i out of mobile phone?

The motor is very weak i tried it and he can't push

what is the name of holder cutter ?

I want file and information about project

mvp

The cat feeder still for sale?

it is still working after 1 years ?

store link is broken

did he say "immortal" or "a mortal" ESP8266 chip :D

OMG! Building a space ship? Your device will fall down after a push of a dogs paw. Useless, expensive (3D project!). Only looks cool