I'm sure they will find something to complain about 😂

U Bet

Yeah, so real😅

Who cares if he is?

Yeah that guy is a jerk. He would complain no matter what.

"zero" emissions?.

I am a little angry I sold my 420/amr300 kart , just fuel and noise. This is way cooler

I second that .👍😎🏁

I agree! It looks like this thing would truly shine on a track with major elevation changes (like 1000 feet). You could always go to an overdrive ratio on the final drive. Make sure your ramp up rate is maxed out on the controller.

😅😅

Legit as in actually do it? So videos would be really hard to make and upload??

This is old school. This is how it was done in the 80s with actual cars. 40 years later it's still epic. Electric vehicles have come a long way, but this kind of ingenuity is still necessary. White zombie is a drag racer that got rubber in all five gears. Electric drive. Datsun 510. From chat gpt because I am lazy AF. The White Zombie is a modified 1972 Datsun 1200 electric drag racing car that gained fame for its impressive performance. It was converted to electric power by John Wayland and became known for its incredible acceleration and speed. The White Zombie helped to popularize electric vehicles in drag racing circles and demonstrated the potential of electric power in high-performance applications.

Do you know how torquey electric motors are? Goodbye clutch.

Could help with the feeling during takeoff, but i think he’s more worried about the gears getting smacked by the jumpy throttle of the motor

A cush drive would help.

​@@LemonySnicket-EUCcush helps everything. 😂😅

Best solution will be a programable throttle

Yeah he needs a more powerful controller and battery to really push that motor

Peewee hermon of 2024

this right here, this needs to be done!! I want one

Normally the trans case has a vent tube. I guess they don't install it when you get it in a kit.

zero doubt

Chain gaurds forever

2 guards I believe in when it comes to moving stuff, chain guards and grinder guards. Both are common for dudes to encounter and failure can be catastrophic. Just takes getting stung by a wasp and torquing a cut disc to send a piece into your mid section. Chains are just nasty when they fail period, without a guard.

Man if it works its not dumb. !! 💯 % correct ....

Jerry rigging or what you guys call it in the south bigger rigging

Like the glue used for the oil leak.

Actually, 60 rpm is sufficient for this task. The whole point is to maintain dog gear contact while limiting wasted energy, why use higher rpms when they require more power?

Yeah, and then don't need the clutch too, I'm proud that I can quick shift manually lol (just cutting throttle)

I did that on my Yamaha for a long time.. only used clutch jn first gear for take-off

Story of my life… 😂

Why

​@@nickbowker5134chain directly behind your head with a electric motor putting a bunch more torque than a gas engine has to a chain designed for a gas engine....that's why. Pop,slap, and that's your end

@@nickbowker5134 safety first.. its better to feel bad about a snapped chain, than a ruptured arm/body

The Motorcycle Company Zero has no transmissions on their bikes. when I read the article about the KTM and the Zero going head-to-head they were all scratching their heads that KTM even has a transmission.

I doubt he would like that, he just enjoys his freedom and no responsibility to anyone else. Just doing his own thing

He needs a bigger drive side sprocket.

at best both.. smaller at the rear and bigger at the front... and maybe he can Programm the controller to higher rpm

Just spool gun mig it up.

@@andrewslagle1974 I would have tapped the hole and installed a screw. But JB Weld works great, never seen it fail.

marine tech is wayyyyyy more reliable than JBwelds joke of a product

Agreed jb weld is temporary