Thank you John for kind words 👍

And watching 😀

​@@tomislavtomasicwoodturning❤❤❤❤❤ bu

Thank you very much for kind words, he is my mentor and I very much appriciate what he is doing for us turners..... His teaching is in my books the easiest and most enjoyeble .... Glad you are sharing my vision.....

Richard Raffan is a famous turner ! He is m'y teatcher since I turn modestly !😉

Thank you, this kind of work I enjoy probably the most, I made these quite often

Thank you for kind words and for support....🤗

Thank you very much 🤗 glad you liked it 😀

Thank you for watching and for kind words, I always try to do something similar on lids

Yes that’s really clever. I’ve done something similar when rough turning (after watching Richard Raffan) but incorporating the shelf into the final design is excellent 👍

@@leftmono1016 indeed I do similar stuff but after it dries, I learn this from him whom I consider to be my mentor..... And best teacher.....

Thank you 🤗

Thank you, he is my mentor after all☺️

Thanks for watching 🤗

Thank you so much for nice words and for watching 🤗

Thank you very much 🤗

Thank you 🤗

Hvala Vam puno 😀

Thank you for watching

Thank you for very kind words, thank you for support 👍

Thank you for watching and support, very kind words 🥰

Richard is my mentor so a lot of I learned from him.....

Thank you for watching 🤗

Its a great thing to make and hone skill since it has most of the cuts on the cross grain

Thank you kolega👍

Thank you very much 🤗

Thank you

Thank you very much 🤗

Indeed,little bit of show of, thanks for watching 😀

Thank you very much 🤗

Thanks so much for watching 🤗

Thank you for watching 🤗

Thank you

Excellent eye🤗 thank you very much

Thank you,I learn it from my mentor Richard Raffan 😉

Hvala kolega 😀

Thank you so much for kind words 👍

Thank you, for watching and kind words 👍

Thank you so much for watching 🤗

That is the hard part😅

Thank you sir😀 its really rewarding to make one 🤗

Thank you 😀

Thank you very much

Thank you very much 🤗

Thank you very much, its even worse in my part of Europe.... Try to find someone a bit further out, and maybe spend a bit more but it will be worth it

You should look into the American Association of Woodturners. They have chapters all over the place with people who like to help others learn woodturning.

Thank you Mike for kind words , and thank you for watching 😀

Thank you, glad you liked it

Thank you sir 😀

Thank you soo much Stuart, It means a lot.... 😀

Thank you

Thank you 😀

Thank you Brendan for kind words, all the best to you as well 😀

Thank you so much for those lovely words.... Comments like this really help to keep making videos.... Thanks once again 🤗

Thank you very much, Richard is my mentor and a great influence so I do have a lot of his skills

Thank you very much for watching and comment 😀

Thank you very much 😀

Thanks 😀

Thank you Robert, it means a lot 🤗

Thank you very much 🤗

Thank you 😀

Thank you very much 🤗

Thank you very much 😀

Thank you for watching, I do like usable stuff, but natural edge has something that is hard to beat....

Thank you for kind words 👍

Thanks I really appriciate 🤗

Thank you 🤗, its very safe if you are using good wood without splits,and cut recees or tenons accuratly.... I've never had bowl fly off the lathe😀 thank you so much for support

Thank you Sir😀

Much appriciate, thank you 😉

Thank you🤗

@@tomislavtomasicwoodturning ok

Thank you very much 😀

Thank you 🤗

Indeed I do ... Thank you for watching 🤗

Thank you very much

Thank you for watching and comment 😀 I rarely measure angles, I use them and if it works great I replicate it...that being said I did measure for begginers series and its around 40 and other one goes sometimes down to 30 deegres.... 30 deegres is great for detail work.... I sharpen all by hand so angles do vary a bit.... 10mm gouge with 30 or even less is a great tool to have for detail...my next purchase😉... I'll explain in spindle work chapter on beginners series for to use spindle gouge so that might help.... Glad you liked the bowl.... Its one of my favorite stuff to make... expecially bigger quantuties

Thank you 😀

Go for it, its a great thing to make and it does have almost all cuts on cross grain orientation 😀 thank you for watching 😀

Thank you very much for kind words, and for support.... Finish is just a simple linseed oil with beeswax mix on the lathe...

Thank you👍

Thank you

Thank you 🤗

Lijep pozdrav, hvala vam puno,pratim vas rad neko vrijeme na UKpostsu, super ste mi.... 😀

@@tomislavtomasicwoodturning hvala. Ali borim se sa ovim kanalom.

@@tomislavtomasicwoodturning koliko dugo ste vi vec na youtubu?

@@Pipejawood-Woodturning mislim da sam prvi video stavio prije godinu dana, pa nisam 4-5mjeseci nista pa opet jedan, tek unazad 3-4mjeseca sam poceo ozbiljno s tim... A Vi?

@@tomislavtomasicwoodturning ja sam na youtubu 1.5 ljeto. Imam mislim da preko 100 videa i ide vrlo slabo. Neznam sto radim narobe😒

Thank you, No, I'm from Croatia.....👍

@@tomislavtomasicwoodturning Oh yes, you remind me: my old dad did tell me that Prince Tomislav (of blessed memory) was baptised with a Croatian name... the royal family had a policy of using names from the various lands of the United Kingdom of Serbs, Croats and Slovenes (later Yugoslavia)... Dad knew stuff like that. (I was friends with Vladimir when I was still at school as well as his naughty younger brother... but lost touch after university. I think Pnce Vladimir joined the RAF)

👍

Thank you sir, its simple pure beeswax, before it I put linseed oil

Thank you so much for kind words, that sander is home made, to mimick inertia sander wich spins with bowl rotation.....

Thanks🤗

Thanks for watching 😀

Thank you very much 😀

Thank you very much 🤗

Thank you for watching, its Vicmark vm100 with 100mm jaws and in this video I think I had Record power as well, sc3 with 50mm jaws

Thank you, indeed🤗

Thank you Mark, indeed its from old two cherry chisel, its accually older then me, but it serves me awsome for scraping......

@@tomislavtomasicwoodturning That chisel cought my eye aswell. It would be very interesting if you could show how you made it and how you sharpen your Tools. Very nice work and a skilled way producing it. Kind regards Simon

@@simonfischer6088 I have in list a sharpening video and I'll add how to change standard chisel to scraper..... Thanks for support and video ideas..... 🤗

Video editor, simple one

Thank you, there is email on my about me tab on my UKposts channel and I have Instagram and Facebook if you would like to order something ☺️

⁠thank you👍

😀

Hi That model of rikon is very similar to that old one I had, yours is a bit stronger motor.... Rikon has very good lathes....I think it will served you well...

@@tomislavtomasicwoodturning thank you so much, meanwhile I Will keep watching and studying your videos!

Thank you for watching ,it Ash....

Its named blo but it doesn't have dryers and heavy metals....

@@tomislavtomasicwoodturning

Then food safe. Nice work.

Thank you

Its ash, thank you for watching

Thank you for watching, best thing is to just go for it.... Soon enough you'll be addictive to turning😀