Hi 👋 Thank you bro 🤝

Toolception!

That made me lol

It's called reprap. Look it up.

There are dangerous moments, but I will fix it)! Thanks 🫡

@@MA-SH a very cool creation, i enjoyed watching

What the f@#-k , Almost had a heart attack during these moments!

You flatter me) take care of yourself don't worry

That was definitely scary - one kick of the grinder away from cutting your hand off at the wrist...😮

was about to say the same thing

@@shedendman me too!

Just use larger tubing then. 😊

With it being on its corners instead of the flat wouldn't that add a less flex?

Yes bro

Everything is copied.

A copy is an exact repetition of something! and no one has such a design

@@MA-SH It is largely based on old DIY CNC designs that I have seen 10 years ago. Main difference is that they put the bearings at an angle so that they run flat on the surface.

Здравствуйте, огромное вам спасибо, приятно когда есть понимающие люди, всего вам доброго 🤝

Этих "показов идей" криворукими "мастерами" полный ютуб. Ничего нового: "гениальная идея" и криворукое исполнение, видосик ради видосика.

В самой идее каретки ничего нового нет, а подобная идея КАК сделать эту каретку не позволит получить хоть на сколько-нибудь жесткую конструкцию, сам подход колхозный. Но люди насмотревшись подобных роликов побегут повторять, тратя время, силы и средства.

​@@user-pe3vn4th5l Главное чтоб люди хоть что-то делали, набивая свои шишки и оттачивая скилл, а не валялись на диване посасывая пиво или пробухивая недели например!

@@user-mb1ib6vo2n Срать в окно тоже входит в твоё "что-нибудь" ? Так вот этот ролик по пользе примерно как оно самое.

Для моей цели достаточно кромочника и он отлично справляется, на счёт двигателя согласен, болгарка еле тянет! Спасибо

А вот вам вопросик можно ...есть такие брашировочные машинки - они с регулятором оборотов и длинной осью 100 и более мм, а ещё есть шлифовальные с регулятором (ну соответственно для полировки кузова авто применяются) - так вот пытаюсь понять не одно ли это и тоже ? Ну да, там ручки по разному расположены , а в остальном ...

для полировки частота меньше- чтоб не "палить" поверхность..плюс можно эксцентриситет добавить...и они на оси мотора сидят(или через редукторные- но в осях. ) брашировалка гораздо мощнее. и+ болгарочная брашировалка- она дает кривизку из за прижима руками- но это не сильно важно. есть макитовские брашировалки с подшипником и креплением второго конца...на таком же принципе устроена камнегрызущая брашировалка-только там не щетки , а твердосплавные звездочки ...(ответил , как понял ваш вопрос)

Пару промежуточных опор добавить и ничего не продавится

@@VLAD18041976 это только для продольных- на каретку надо фрезером давить-иначе будет фигня...я ж работаю на аналогичном инструменте. тутвообще другие ПОДХОДЫ к работе. для потока надо конструкционный профиль (почти ЧПУ...ручной) . а для периодики хватает каретки из фанеры по всей ширине доски а опорные длинные-это вообще брусок ккалиброванный....ну поверьте..это работает у всех...

Thank you so much, friend! Huge greetings from Alexander from Russia 👋

Thank you! I got time economy to understand that this device is not necessary for me )

@psiholog-nikita-kozin Thank you bro 👍

I wish people would show the device working at the start of the video, and then people could decide to watch the construction. Watching someone drill a hole or cut a piece of steel gets boring pretty quickly.

What you do is, put time as 6:20 that make it jump right there!

Thank you

I enjoyed the content. I was just imagining my health and safety officer at work, losing his mind at me if I was doing it 🙃 😆 🤣 😂 struck me funny is all. 😀

Thank you my friend 👍

In italia a CENTO in provincia di Ferrara la INCIMAR costruisce pantografi dagli anni 80 oggi sono tutti compiuterizzati

@@user-li1mk5rk8i 👍

You people are clueless 😂😂 Its honestly comical how many uneducated people with zero experience feel the need to comment on things like this. Grinder discs WILL NOT cut through fingers 😂 I’ve hit my handed with them plenty of times, best case it makes a small tear.. worst case the blade will shatter on impact and leave you with a slightly worse cut.. Picking up a piece of 4’x10’ sheet metal in my shop poses a WAYYYYY higher risk of major injury than using a grinder (especially when you’re experienced with it..) Keep doin you Master Sh. Don’t listen to the whiners 😂

Everyone has their own opinion, no matter who they are 🤭

Спасибо добрый человек

Thank you my friend 🤝

Ok thank you

so where do we find your video!

@@relentlessmadman 🤭

@@relentlessmadman Very few video's were made in the 80s

Hello friend 👋Thank you so much 👍

😊

ukposts.info/have/v-deo/qnxhmJ-Kfnuk1aM.htmlsi=xETt2JdJvPWL29Sh thank you 😊

@@MA-SH Essentially a surface grinder. Though the wheel is a brush. Easily as interesting as the main focus of this video.

ikr? i wasnt sure what was cooler, the motion system or the cleaning tool lol

It's just wonderful 👍

@@MA-SH Better than that , it's simple !

Hello, thank you! I used a sander and sandpaper for 60

Your advice also helped me, the handles on the sides will be just right! Thank you very much 👍

Good idea!

@@MrDhandley Thank you bro

David was good in his day 🧙‍♂

Thank you

Hello 👋 Thank you my friend 👍

This is called a router sled, and its purpose is flattening slabs.

Thank you bro

🫡

Seriously. Please learn how to use an angle grinder safely, then reshoot and repost this. Even with all the "idiots with a bucket of tannerite" videos on UKposts, your video is the most dangerous I have ever seen.

Your comment is more dangerous than my video

Are you some sort of water head?

Clearly unnecessary . There was no blood!

Hi friend 👋Thank you so much 🤝

Hice lo que fue, gracias

Damn..I should have watched your video.. I,m such a fail😢

@@shroommcfanta2020 Way to demonstrate that you have no concept of this thing called "constructive criticism". You're right. You're a fail. Crawl back under your rock.

Hello, I understand you! Thanks for the advice!

🥺

No, you are wrong. As a quick, easy, cheap, repeatable and efficient method to rough out a flat surface on large timber surfaces this just about hits the spot. Great idea!

Thank you my friend 😊

Bonjour, merci beaucoup

Hello 👋 Thank you bro

Приветствую Денис 🤝 Огромное спасибо 😁 Шеф👍

Жиром не подавись, чyчeлo безграмотное. Расширяй словарный запас, примитив.

Hello, thank you so much friend 😊

Ein Freund werde ich bald mit einer Elektrobank machen, in dieser Situation braucht es viel mehr Platz für einen Hobel

Der Bosch GHO 26-82 hat Anschlagsflächen mit Gewinde, wie gemacht dafür...

Hola, muchas gracias! 🤝

Hi 👋 Thank you bro👍

it can't, so the shooting is accelerated 5 times

@@MA-SH No offense, I think I just saw too many "oh no, I cut myself on the tablesaw"-videos lately 😀

@@michaeltrojanek9392 ok 😂

@@michaeltrojanek9392 A handheld grinder with an abrasive disk is not a table saw.

Thank you my friend

They should, but for this length and a small milling cutter is no longer needed, and at the end it is clearly shown with the help of a level that there is no deflection, then why write about it?

Николай жму руку 🤝

Hello 👋 Thank you my friend 😊

Hi👋Thank you so much 👍

Огромное спасибо 😊🤝

Согласен, но тогда нужно и там подшипник делать 👍

Просто приварить к каретке две ручки , как у большого фрезера . Будет на много удобней

Thank you buddy 🫡

Hello 👋 Thank you so much 👍

Хорошо, переделаем на толстый 🔩

​@@MA-SHЧто ж хорошего? Слепил какую-то куйню 🤮🤔

​​​@@MA-SHклассная задумка, палец вверх! Обязательно повторю но надо что-то попрочнее, в этом варианте пустить шпильку по всей длине внутри профиля. Удачи!

@user-wq2me6yn8t Для тяжёлого фрезера конечно нужно профиль помассивнее, но в данной ситуации фрезер игрушечный)) Спасибо 🤝😊

Кто это )) ты болгарку то в руках держал 🤣

Hello 👋 Thank you my friend 👍

I only have such a milling cutter, I did it to align one countertop

Very good bro, thanks 👍

Thanks

👍

Thank you for the helpful advice 🫡

Hello 👋 Thank you very much 🤝

Здравствуйте, благодарю 🤝

только вот идея не принадлежит автору😁

@@wintdgy2369 так же как и моя конституция другим авторам!

Hola, gracias 🤝✊👍

Thank you bro

You mean the long rails? Or the short ones? Of course the long rails have a corner up (which seems like the least stiff configuration, am I not correct?) to keep the rollers from falling off.

@@rodschmidt8952 meant the short ones. When watching the video you can notice slight flex in those short rails where router sits. It might come from the weight of the router or from pushing downward with your hands. But then of course this can be considered as "good enough" for hand planing later :)

Thank you so much 👍

I would add bearing rollers to the cross slide as well once the rails are turned 45 degrees, instead of box section sliding on box section, same as the longitudinal setup. Great job though.

Thank you my friend 🫡

Hello 👋 Thank you bro 👍

🫡

Что ооо 🫣

Hello 👋 Thank you bro 🫡

Hi friend 👋Thank you buddy 👍

Thanks

Hello, thank you very much! I didn't even know there were such things) during the tests, I changed the bearings to sealed ones, pay attention to the video preview!

Hello 👋 Thank you 👍

Thank you bro 🤝

Thank you my friend 👍

Could you drop a link to your video?

@@MA-SH I'm not a creator, i don't make videos. i have just short how it works on my profile

@@aniolo5 I get it, good luck

Ok thanks

Hello, thank you so much? Okay, I'll be careful. 😊

Thanks 👍

Muito obrigada🫡🤝

Muchas gracias amigo 🤝

Witam, dziękuję bardzo 🤝✊👍

Thank you my friend 👍

Ok friend, thank you 🤝

Hi 👋 Thank you buddy 🫡

👍

There was no other milling cutter

@@MA-SH It'll work just as good.

Hello, thank you very much! Sony A6400 Camera and Sony 18-105mm f/4G OSS PZ E lens (SELP18105G) Best wishes from Siberia ✊👋🤝😊

당신에게 너무 많은 친구를 감사 🫡

Hello, thank you so much! Thank you for advice 👍

@@MA-SH I'm a mechanical engineer consultant, prototyping is a big part in my life.

Dobrý den! Díky moc! A chtěl jsem říct, že české pivo je nejlepší🍻

Hello 👋 Thank you bro 👍

Thank you bro 👍

Yes,write something new, otherwise your comment looks like that bike

Dobrý den, moc děkuji! 👋

😁🤝

😊

🫣🤭

Thank you 👍

Specialty blades and I am willing to bet more people have routers than planers . That is my guess.

The plane takes up a lot of space, it needs a large area to work if it is a design like with a milling cutter

It’s not the efficiency of the tool, it’s the ingenuity shown making a tool to work for him.

The power plane is only about 14in. long, which makes it inefficient for flattening things more than 28in. long. This means you have to do a lot of checking a you go to make sure you're heading towards flat. Long straight edges, winding sticks, small passes, etc. Router sleds, if the rails are stiff enough, are much more precise and easy to use.

Bonjour, merci beaucoup 👍

Thanks

There are dangerous moments, but I will fix it)! Thanks 🫡

🤷Thanks

Thank you buddy 👍

Olá amigo, Muito obrigado 🤝😁

Thank you bro 🤝

Thank you bro 👍

Thank you bro 🫡