#409

День тому

Often viewers ask in the comments: Why do you still use batteries and not supercapacitors for your projects? Good question. Do you know the answer?
Supercapacitors are super like Superman or Superwoman. Otherwise, they only would be called “Capacitors.” Right? Where are they “super” and where not? Where can we use them, and how? And the most important question: Are they better than batteries?
I am a proud Patreon of @GreatScott!, @ElectroBOOM , @Electronoobs , @EEVblog , and others.
Links:
Other Capacitances: s.click.aliexpress.com/e/_9g2z16
Small Boost converters: s.click.aliexpress.com/e/_A2DZ2G
Electronic Load: s.click.aliexpress.com/e/_9JHlLc
Types of Capacitors page: www.electronics-tutorials.ws/...
100F Supercap (probably fake): s.click.aliexpress.com/e/_A5rin6
The links above usually are affiliate links that support the channel (no additional cost for you).
Supporting Material and Blog Page: www.sensorsiot.org
Github: www.github.com/sensorsiot
My Patreon Page: / andreasspiess
Discord: / discord
If you want to support the channel, please use the links below to start your shopping. No additional charges for you, but I get a commission of your purchases to buy new stuff for the channel
My Amazon.com shop: www.amazon.com/shop/andreassp...
For Banggood bit.ly/2jAQEf4
For AliExpress: bit.ly/2B0yTLL
For Amazon.de: amzn.to/2r0ZCYI
For Amazon UK: amzn.to/2mxBaJf
For ebay.com: ebay.to/2DuYXBp
profile.php?...
/ spiessa
www.instructables.com/member/...
Please do not try to email me. This communication channel is reserved for my primary job
As an Amazon Associate, I earn from qualifying purchases
#no#midroll#ads

КОМЕНТАРІ: 537

@drmocm 2 роки тому

1 Farad = 1Coulomb /Volt , i.e. the amount of charge per volt that can be held. Charge can be written as current times time C = A*s. Voltage is energy per charge, i.e. V = J/C= J/(A*s). So we get F = A*s²/J. Now, energy is force * distance, J = N*m. Force is mass times acceleration, N = kg*m/s². So J = kg*m²/s² and F = A²s⁴/(kgm²) in SI units.

@AndreasSpiess 2 роки тому

Thanks for the explanation! Seems logical.

@pjn1988 2 роки тому

It's kilogramm because this is the standard (SI) unit for mass (remember the "Urkilogramm"). vy 73

@anvou2 2 роки тому

_E = 0.5 · C · U²_

@uwepolifka4583 2 роки тому

wikipedia.org/wiki/Basisgr%C3%B6%C3%9Fe

@klausbrinck2137 2 роки тому

The easiest way to solve physics-exercises at school: Solve, without any plan, knowledge or backthinking. Check the SI-unit of your solution. If you´ve nailed the unit, your solution-pathway was possibly the correct one, as is the solution itself (probably ;-)

@peter.stimpel 2 роки тому

Nice video. I found 2 usecases for those supercaps so far: UPS stuff to help between the different stages of recovering power for IT stuff, and this one: charge one up, and throw it to someone you dislike. The person will catch it, and you will have fun for a short period of time. Disclaimer: do not try this at home ;)

@AndreasSpiess 2 роки тому

I am not sure about the second "use case" (if 2.7volts are enough). The 400 volt cap from the coil gun probably would create more fun ;-)

@peter.stimpel 2 роки тому

@@AndreasSpiess we used so called gold caps, but this was many years ago. I do not remember of any details except the result

@acopernic 2 роки тому

The first usecase is a good idea especially for outside ups system. No maintenance as well.

@scurvofpcp 2 роки тому

Pilfer the cap from a camera flash for your second use case.

@ericb5193 2 роки тому

Great video once again! I use the TPS63900 Buck-Boost converter in combination with a BQ25504 energy harvester and two supercaps in series in a sensor project. Works great! The TPS63900 is a relatively new buck-boost converter (1.8V to 5.5V, 75nA IQ) from TI for low power applications. Unfortunately, the chip is currently hard to get.

@AndreasSpiess 2 роки тому

This TPS63900 seems to be a great chip. Together with the BQ25504 it gives a good design for an indoors light harvester like thee Enocean sensors. What kind of MCU do you use for the project?

@Mr.Leeroy 2 роки тому

NCP1402 is cheap and comparatively close if you are ok with fixed output

@jR060t 2 роки тому

Why not use the BQ25570 or parts from other vendors like the AEM10941 which have buck boost regulators onboard?

@ericb5193 2 роки тому

@@jR060t About 2 years ago I made a prototype PCB with the BQ25570. It is a very good chip, but not suitable for the current design, because it has only an output current of max 100mA (the TPS63900 delivers up to 400mA -> required for NB-IoT / CAT-M1) and because with the required output voltage of 3.3V you need also at least 3.3V at the supercap (the output stage has only a buck converter). Thus only 3.3V - 5.5V can be used from the supercap's voltage range. With the TPS63900 on the other hand the full voltage range from 1.8V to 5.5V can be used (buck-boost converter), which results in about 40% more capacity.

@ericb5193 2 роки тому

@@Mr.Leeroy I did not yet know the NCP1402. A glance at the datasheet shows me that the Iq is 30uA, this would be too high for my design (The Iq of the TPS63900 is only 75nA) and it looks like it's a boost converter only (see also answer above)

@alexandern8671 2 роки тому

Excellent video as usual. Two comments: - the unit of capacitance is defined using primary SI units. As it turned out, our world as we know it can be described using only 7 different physical quantities. Sometimes their combination could look funny indeed. - Another use case for the supercaps is for keeping low power RTC ticking when the external power is removed intermittently. I think many GPS receiver modules are equipped with a supercap to allow for the warm start, especially in mobile systems in cars where the supply voltage can drop when the engine starts.

@AndreasSpiess 2 роки тому

1. You are right with the SI units. But also for me they sometimes look funny. 2. I thought the GPS modules have small batteries. But I am not sure. At least I had some issues with T-Beams where the "battery" was discharged when they arrived from China and the application did not work anymore. I had to use a sketch to reset the GPS module. It seems to be a problem well known to the specialists.

@tinkerdave3157 2 роки тому

If you have a project that uses a battery whose inner resistance is getting higher and higher over time, a supercap can also be very helpful. Espacially if you need higher currents over a short period of time (motor, communication...) it can be used to reduce the voltage drop over the inner resistance.

@AndreasSpiess 2 роки тому

Interesting idea. So far I usually replaced the battery because it also lost capacity.

@tinkerdave3157 2 роки тому

@@AndreasSpiess I use it to get the longest battery lifetime out of primary cells. It works really well.

@spicybaguette7706 2 роки тому

@@tinkerdave3157 So the supercap essentially acts as a sort of buffer?

@EgonSorensen 2 роки тому

@@spicybaguette7706 It is a capacitor, so yes - it acts as a buffer if/when a batterys internal resistance goes up. Unfortunately super capacitors also has a (sometimes quite) limited life span, before they also starts to degrade.

@siberx4 2 роки тому

This might also work well to assist batteries used in cold environments; internal resistance of most battery chemistries goes up substantially in the cold, even for fairly new cells. A supercap in parallel could provide sufficient buffering for bursty high-current loads in outdoor projects expected to handle below freezing temperatures.

@ShungerYunger 2 роки тому

I recently used a supercapacitor on an ESP32 project, in combination with a Lithium Thionyl battery. The ESP32 was used as a wireless sensor, mainly powered by the battery, but because lithium Thionyl batteries can only supply really low currents the supercapacitor was used to assist with the current delivery during wireless transmission! Was really interesting to design

@AndreasSpiess 2 роки тому

What was the challenge?

@ShungerYunger 2 роки тому

@@AndreasSpiess We were building these wireless sensors that would send measurement data wirelessly to a central gateway using ESP-Now. These sensors were powered using Lithium Thionyl (didn't want to use Li-ion/Li-po for safety reasons) batteries which can only supply very low current (50mA continuous, 200mA peak). This was fine for the measuring but during sending we had to add a supercap. But to be able to use the supercap we had to limit the charging, because otherwise the charing of the capacitor would put too much strain on the battery, so we had to limi that with a resistor, then we needed a way to use the full power of the supercap while discharging (using a P-Channel MOSFET).

@ShungerYunger 2 роки тому

The measurements are taken from the temperature of the room of a house and the temperature of the water going into/coming out of the boiler for central heating. With these measurements the aim is to create a model to improve efficiency for heating of homes

@AndreasSpiess 2 роки тому

Is your diagram public domain? I am sure it would be interesting also for other viewers!

@ShungerYunger 2 роки тому

@@AndreasSpiess Unfortunately not yet. It is planned to become open source (both the hardware and the software) when the development is finished. I will post a comment here with a link to the schematic and firmware for the devices!

@JamecBond 2 роки тому

9:45 I believe you did miss something, the reason behind the hype for super capacitors is probably their cycle life/capacity. So in the long run a single super capacitor will be able to store and discharge more energy, even if batteries have a large capacity their cycle life is very limited, thus their lifespan is weak. With the constant obsession over "sustainability" this fact would be a major driving force behind the super-capacitor hype.

@AndreasSpiess 2 роки тому

I agree. And I thought I mentioned the fact.

@klassichd10 2 роки тому

Thank you for the interesting contribution and the realistic calculation. About 6 years ago, I designed grid failure detection units. First I used supercaps to deliver the energy for the transceiver informing me after power loss. Studying the data sheet of the availabe types (6 years ago), I missed any statement about lifetime and endurance of the supercaps. But there was a hint about drying out over the years. And the low temp range was limited to -20°C or so. So, I created a parallel design using lithium primary AA batteries. These are rated for 20 years shelf time typically. Perfect for that application - and cheaper and easier to use. And the temperature range for these batteries is great, too -40°C to 60°C.

@AndreasSpiess 2 роки тому

My "Windwächter" which retracts the awning in case of high windspeeds uses a super cap and a solar panel. I assume they wanted it to be completely maintenance free and therefore avoided batteries. It is now nearly 10 years old and still seems to work. But I am not sure because I added my own system in parallel because I wanted it also extended with a lot of sun. AA batteries for low power applications still are a very good choice. And now with my supply of nearly unused Lithium AA batteries from my hunted weather balloons I am not short in supply. And they easily seem to work down to -60 degrees on 35'000 meters.

@klassichd10 2 роки тому

@@AndreasSpiess Yes, that is a very special method of "harversting" very good batteries! Im my vicinity there are no ballons landing. All captured by you!. So, I keep it easy and follow the former ETH expert Rolf Zinniker and CH "Kassensturz" (2014). Using batteries of south German discounters for general use. And these lithium ones for special use. AA are cheap and versatile. I have many zigbee motion sensors, attached and kind of integrated on/in furitures. There, I am using external AA batteries instead of the internal coin cells. Cheaper, higher capacity - and replacing batteriers without touching and re-adjustment of the sensor's position.

@AndreasSpiess 2 роки тому

I have 3 Aquara sensors in the lab and after month of usage they still report nearly 100% battery. I am curious when I have to change them. A wonderful technology... And I agree with Rolf's analysis (as a former ETH student I probably should). BTW: I do not drive far over the German border for the balloons. There a few others are also chasing and I am too slow ;-)

@TishSerg Рік тому

@@AndreasSpiess Wow What is that weather balloon hunting? Are these weather balloons that some makers launch and you shot them down for spare parts? Or why do you even want to shoot it down? Is that legal to destroy other people's apparatus? :D Or is it some sort of national fun? :D BTW We too have to deal with balloons, that ruzzians launch to distract our anti-air defense.

@donaldkormos5529 2 роки тому

Very informative video!! One application for supercapacitors which has proven very useful is in model railroading. They are used in what's called "Keep Alive" circuits which can be commercially purchased or home-built. Very often, they already come installed in newer model railroad engines. Momentary disruptions in the track voltage due to dirty track or short track gaps are not good. So the supercaps only need to supply energy for very short periods of time ... like seconds. However, the voltage requirement is higher ... typically 15 to 20 volts. If you use supercaps which are too big in farads, maybe the train engine wheels will keep going if you have engine derailment!!! My application is for an ESP32-CAM module which is built into a HO-scale boxcar for wireless train video. For this, I use two 0.330 (or 0.500) farad, 9-volt supercaps in series. This seems to work well.

@AndreasSpiess 2 роки тому

Interesting application. I am a sponsor of such a model railroad club (morges-trains.ch) which is operated by a relative of mine :-)

@wayne6220 2 роки тому

Thank you, very good video. I have seen before people using the balanced board with super caps as a car battery replacement, however I would worry about it going flat between engine starts.

@AndreasSpiess 2 роки тому

Because they are hyped they provide good titles for UKposts videos ;-) But, as you say, probably not a good board.

@porcodomal 2 роки тому

Great video! There are different classes of supercaps, some for low power consumption, low current leakage and long time duration, keeping an RTC for example. These are not made for high current consumption. Other classes are for the opposite, can support high current, but have a huge current leakage and will last less time. Neither are the best option to keep a higher consumption device for a long time.

@AndreasSpiess 2 роки тому

Thank you for the additional information!

@AlexCorvis666 2 роки тому

Awesome lesson Adreas! Thanks a lot for your class!

@AndreasSpiess 2 роки тому

My pleasure!

@xDR1TeK 2 роки тому

Wonderful presentation as always. You're a valuable asset to the community and to the world at large.

@msana4420 2 роки тому

😂😂 Presentation

@AndreasSpiess 2 роки тому

Thank you for your nice words!

@halitekmekcioglu7150 2 роки тому

Nice video, I was used them in my final thesis to get higher amps for miliseconds. It worked though, as you mentioned it’s not the best for small and tiny electronics.

@AndreasSpiess 2 роки тому

Thank you for sharing your experience!

@johnlh100 2 роки тому

I'm using supercaps in parallel to LiSOCl2 AA-Batteries (non rechargeable, e.g. SAFT LS14500, 3.6V 2.6Ah, ~3€) for powering ESP8266 (ESP-01) boards in combination with BME280 sensors. They provide p,T,h readings every 15 minutes (indoor) with deep sleep in between and battery lasts for 1.5~2 years. The supercap hereby covers the current peaks during WLAN connection until complete discharge of the battery. The setup is very simple as it does not require any voltage stabilizer. Thanks for all your great videos!

@AndreasSpiess 2 роки тому

Thank you for sharing your project. A good use for such a cap because these batteries have a high internal resistance.

@navigator_071 2 роки тому

As always - Extremely effective video, typically Swiss. Thank you for the noble work of sharing your knowledge.

@AndreasSpiess 2 роки тому

My pleasure!

@Ed.R 2 роки тому

Very good summary of super capacitors. As I discovered from the FAD buoy which I took apart, video on my channel, super capacitors do have a use powering devices in some applications. Reliability is one of them and no loss of capacity. The buoy is very much a sealed for life device. The fish locating echo sounder is very high current when operating although for short bursts. I've yet to use it in a project and it came with a great solar panel. Would make an incredible solar garden light. The capacitor still has a charge in it from around 1½ years ago which I thought was incredible. Good quality capacitor but rather expensive and large.

@AndreasSpiess 2 роки тому

Indeed, it would make a exclusive garden light!. I wonder why they used a super cap in this design because the temperature variations are not too big and I would assume that the device will not last forever. But obviously they trusted this tech more than the batteries and they had enough space... BTW: I see that you also are a bicycle enthusiast! I gave up with measuring power when I bought my new bike and ordered one with a built-in sensor. They came down in price.

@Ed.R 2 роки тому

@@AndreasSpiess I'm a bit obsessed with my automatic shifting bicycles and the power meters. Always developing the code for the shifting, currently switching to an external EEPROM. The power meter is currently providing quite successful but depends what you want out of it. It will never achieve 1% accuracy but has mostly been + - 5W of my Garmin pedals for a ride average so good enough for me. Just about to receive some costume HX711 boards for it with 116Hz sample rate.

@jessstuart7495 2 роки тому

I wish a car company would produce a super-cap gas (or diesel) hybrid. Have just a large enough super-cap bank to accelerate the car up to highway speeds several times and provide a place to dump energy during regenerative breaking. This would allow a car to use a small, light, and more fuel efficient engine. Hauling around an engine that can produce 200hp seems silly when it only takes about 30hp to drive down the highway.

@NiHaoMike64 2 роки тому

A friend of mine had the idea for a car that used supercaps to start the engine. She then thought if it could be extended to accelerate the car to highway speed and it turns out the capacitance required is something silly like 3F at 450V.

@AndreasSpiess 2 роки тому

I am sure we will see many new concepts in cars over the next few years. This development just started (compared to the long history of combustion engines)

@max9111 2 роки тому

Hype is the pit of science. Anyway, interesting video. Thanks.

@AndreasSpiess 2 роки тому

I agree.

@PortableRadio 2 роки тому

Thank you Andreas for this great presentation! As always very well explained and well researched.

@AndreasSpiess 2 роки тому

Thank you! You are really very active in SOTA Portable Radio ;-)

@PortableRadio 2 роки тому

@@AndreasSpiess Yes, I like to do SOTA, but not right now, with this terrible weather ;) To me, SOTA combines several great things, like technology and outdoors. And there are several summits in your vicinity that you could probably reach directly by foot. Not like me, who lives in the city. Your channel is a fascinating source of inspirations!

@AndreasSpiess 2 роки тому

So far I only tried it once with a colleague. We made two summits in one day. Maybe next summer. Too many priorities...

@PortableRadio 2 роки тому

@@AndreasSpiess Cool! Like you, I did a long ham break before I discovered SOTA. Have fun and best 73, Stephan

@Monochram 2 роки тому

TY Andreas! This was just the video I needed; we have boilers on the rooftoops here, I want to power a setup for reading the temp. Coupled with a smart switch inside my home for powering it, using supercaps might be a good solution instead of li-ion; I thought, thanks for filling out the gaps !

@AndreasSpiess 2 роки тому

With lots of sun super caps are probably a good solution because you do not have to store a lot of power.

@Monochram 2 роки тому

@@AndreasSpiess Since I'm planning to use this also on rainy and cloudy days (even more then sunny ones) photovoltics makes less sense to me, I will piggyback boiler power to charge the caps using a smart switch inside my house. Im currently testing the project using li-ion; Ordered the components before U published this video :) But I'll update here if I have news

@Monochram Рік тому

Well, almost finished the project (again much inspiration from this video); However looks like the setup holds up much less time then I expected. I might have a current leaking "back" to the dc-dc that charges the the caps. should I add a diode between the Buck and the caps @9:39 ?

@bluefishactcl1464 2 роки тому

Very timely work - I needed to hear some one else to make sure I was not missing something

@AndreasSpiess 2 роки тому

Glad I was the one ;-)

@Palominostudio 2 роки тому

Hi Andreas, Thanks for the video and the time that went into putting this together. It is a nice comprehensive comparison between the two energy storage mediums. The caps are good for pulse duty as you said, like providing high current for a short time. Car audio systems which are very high powered are a good subject. One may for instance need 10 - 30 times the output current available of the alternator only briefly. But, as the lead acid battery chemistry is not capable of supplying that kind of current, the caps are perfect. The maths you did confirms my suspicion, because I am too lazy to do the math myself, that the energy density ratio of the two storage devices is quite high. And a chemical storage device is still the best, especially if it has to be portable. The better the batteries, the bigger the issues with the chemistry though. That is the trade off. Anyhow, your video as always goes down well with a Sunday beverage. Kind regards, South Africa

@AndreasSpiess 2 роки тому

I hope you are well because we do not get good news from your region ;-) I thought that car batteries have to be able to supply quite a lot of current to crank the engine. At least more than my audio system needs. Since I am no more young, there are for sure much higher powered systems available than mine...

@arenaengineering8070 2 роки тому

Good and well-founded answer. Thank you for the video.👍🏻

@AndreasSpiess 2 роки тому

Glad it was helpful!

@AdityaMehendale 2 роки тому

Hi Andreas, I would like to add three things to the "lessons learnt" section - from my own experience: 1) Supercaps are not created equal. You have the high-current types ("Maxwell") that have a high self-discharge, but very low ESR, allowing complete charge + discharge in ~ 20 second 2) On the other end, you have the "Sanyo" types - moderate-high ESR, but very low self-discharge. Useful for memory-backups. 3) Often for ESP32 or IoT projects, neither of the above is "just right" --> I came across a "best of both worlds" part made by a company called CapXX (now owned by Murata) that does a decent compromise between the two. It is in the "Goldilocks-zone" when it comes to IoT projects.

@sumantkhalate 2 роки тому

Adding to the leasons learnt 1. They are very sensitive to temperature and voltage, hence a slight over charging or using it at elevated temperatures can significantly reduce the life.

@AndreasSpiess 2 роки тому

Thank you for your additions and your experiences!

@bratwizard 2 роки тому

Thank you for a useful and informative video! I have been wondering about supercaps for a while now, and you hit upon all of the relevant points that I've been mulling over. You did miss one point, however, how quickly they can be recharged. Perhaps you didn't miss it per se, but rather framed it in the context of the "electric car" and thus missed some useful "temporary storage" uses in other applications.

@AndreasSpiess 2 роки тому

As stated in the intro this video is focused on small projects. Making videos means to say "no" to most things. Otherwise the video would become very long ;-)

@bratwizard 2 роки тому

@@AndreasSpiess Right, but that is one of the great benefits they have over batteries.

@murraymadness4674 2 роки тому

Well done video. If you look into LTO batteries, they are like a hybrid between a battery and supercap, can charge/discharge quickly and high currents, but have lot more capacity and less voltage drop.

@AndreasSpiess 2 роки тому

AFAIK they use chemical changes to store energy. So I would count them as batteries. They have their advantages, but their voltage (2.4 volt) is not ideal for our projects. They are probably the best choice for low temperature projects. Unfortunately I did not find standard modules for 2.4V charging or protection.

@hdeamon 2 роки тому

Andreas, good video! But I still think that makers could benefit from using supercapacitors a lot (not in all projects of course). I use a 1.5 F supercapacitor to power my "Wireless solar-powered sensor node" (basically, it is a thermometer) for almost 48 hours. It sends readings each minute (each 3 min when discharged below some level). Also, when using a bare AVR microcontroller we have quite a wide voltage range (1.8V - 5V). I can share a link if you are interested in reading about the project (the previous comment was deleted, maybe due to the link in it).

@AndreasSpiess 2 роки тому

Interesting! You have to send the link via Facebook messenger or twitter. UKposts deletes links :-(

@hdeamon 2 роки тому

@@AndreasSpiess, I've sent it via FB. It also can get easily googled by the name "Wireless solar-powered sensor node".

@cbiz8 2 роки тому

Perfect spanish translation. Felicitaciones!!! Saludos, Carlos, Buenos Aires.

@AndreasSpiess 2 роки тому

The translation is done by Luciana, an Argentinean lady...

@JosepsGSX 2 роки тому

The link in the description mentioned at 1:43 is missing, although I would really prefer to watch something made by you about it, as I really like how you explain stuff. A video that I´d also love to watch would be one discussing alternatives, if any, to retrofit old hardware where electrolytic and tantalum caps are starting to leak and fail, as it is difficult to decide which would be the best reliable alternatives with the current cap technologies. Thanks for the video!

@AndreasSpiess 2 роки тому

1. Thank you. I added the link. 2. I am not in vintage electronics. But if I watch such videos (Mr Carlson's Lab, for example) They usually exchange all old electrolytical caps with quality brand new ones. Usually without measuring them.

@1boobtube 2 роки тому

The Art of Electronics at least the second addition had a section on capacitor types and their trade offs. Since modern electrolytic are smaller sometimes you can gut the aluminum cans and restuff them with better spec's parts than original if you stick to good brands from professional distributers. Some purists want to keep as close to original as possible for esthetics. I guess it depends on if you want to repair it or restore it to original performance and reliability.

@Bertoaus 2 роки тому

Very informative video! Last 2 year I made non-stop solar machines, windowsill size. To bridge the night en cloudy weather I store the solarenergy of the 5V 60mA solarpanel in a 50F 3V supercap. One pendulum is running non-stop for 672 days on 20 micro Ampere (incl. the LCD daycounter). To convert the solar voltage to the supercap I use only a 3V low power voltage regulator. My experience with buck boosters is that they have a high start- and own power use. My advice: With less than 0.1mA use, a 50F supercap can deliver non stop power for a very, very long time, when charged by a small solarpanel. We did enter the micro- and nanoWatt era.

@AndreasSpiess 2 роки тому

Thank you for sharing your experience. Seems to be a good project!

@elpechos 3 місяці тому

What voltage regulator did you use? I have a similar project to this, I Only want to power something that uses about 20uA. Also what supercap did you use?

@Bertoaus 3 місяці тому

@@elpechos The voltage regulator is a 3 pin 3V LP2950 low self power use. As supercap I use a 50F 3V one, charged with a 5V 60mA solarpanel.

@elpechos 3 місяці тому

@@Bertoaus Thanks for that

@WooShell 2 роки тому

I've done the same thought experiment with my Arduino projects some time ago as well.. the 5.5V supercaps would be perfect to replace the USB supply.. but a runtime of only a few hours or a day made it quite clear that there's no real way around LiIon cells any time soon.

@AndreasSpiess 2 роки тому

Thank you for sharing your experience!

@MrSdfghjkl2345678 2 роки тому

Thanks for all the informative videos i've learned a lot, danke schön Andreas!

@AndreasSpiess 2 роки тому

You are welcome!

@BerndFelsche 2 роки тому

Thank you for the overview.

@AndreasSpiess 2 роки тому

You are welcome!

@BensWorkshop 2 роки тому

Useful information and a good reminder of the differences between capacitors and batteries.

@AndreasSpiess 2 роки тому

Thank you!

@sophiesmith5922 2 роки тому

Very interesting. I was wondering how to use this for esp32 cameras with motion sensor project, to connect to lora wan for monitoring. Cameras outdoors in winter, far enough away from building that ac power is an issue

@AndreasSpiess 2 роки тому

You can do your calculations on how big the capacitor has to be and if you do not find a solution with batteries (LiFePO4 batteries can be discharged down to -20C)

@tonysfun 2 роки тому

Well done again Andreas! But it is sometimes like if someone like beef and someone only chicken! People that play with capacitors might disagree..... I agree with your statement and conclusion - for Arduino or ESP projects. Thank you again!

@AndreasSpiess 2 роки тому

You are welcome. That is why I try to focus on use cases. Good or bad mostly are attached to what you want ;-)

@gregorymccoy6797 2 роки тому

Wow, I've had all those questions myself. This addressed all of them plus a few I didn't think of.

@AndreasSpiess 2 роки тому

Glad the content was useful for you!

@joopterwijn 2 роки тому

Thx for bringing the hype back to ground level,.. very informative!

@AndreasSpiess 2 роки тому

You are welcome!

@docjava1 2 роки тому

Great video! However, also consider the Low duty cycle use case . turn the circuit completely off for long periods of time and then turn it on. for example, suppose we want to turn the circuit off for one week and then turn it on for one minute, take a measurement and then turn it off again for another week. Now the only thing we need to worry about is a timer that can turn the circuit on and off, the amount of power such a timer would take, and the leakage of the Super capacitor. There are very low power 555 timers with built-in counters. Hooked to a MOSFET We can easily switch our circuit on and off with a long dirty cycle.

@AndreasSpiess 2 роки тому

Unfortunately, the Supercaps have a relatively high leakage current (compared to their capacity. So I am not sure if they are a good choice for long-term projects.

@docjava1 2 роки тому

@@AndreasSpiess The leakage current will stabilize after 24 hours. After which it is minuscule. Yes you will need to measure the residual Energy left in the capacitor after a time that depends on the application (a week? a year? I don't know.). As an experiment, I charged a capacitor on my desk and let it sit for a week. It still has voltage you can measure. The voltage is much lower, typically around half to 1 V. Still, it may be enough for the application: depending upon how much energy is required and over what period of time. It all depends on the application. The CSS555 is a micropower version of the popular 555 timer IC. It features an operating current under 5µA. Using a long duty cycle should enable the buck boost to be turned off while the super cap leaks. I have a super cap that registered 0.3V after a year of sitting. IT is a 5.5V 4.0F cap (cheap and unremarkable). It contains 0.3*4F= 1.2 joules of energy (after a year of sitting). With 5 of these things, you could get 1.5 v, even after a year (and they are not very big). Not much, power, I grant you, but not zero either. A next generation rfid tag has a power consumption of 700 nA at 1.5 V. (1 uW).

@no8reek 2 роки тому

Very interesting and thank you for the understandable explanations. Have a project that we need to detect power failures/drops. We need to run the 3/4g modem and the mcu for a number of minutes after power failure detected. Do you have a project using super caps that can achieve this?

@AndreasSpiess 2 роки тому

I once made a video where I used supercaps to power a Raspberry for a safe shutdown.

@no8reek 2 роки тому

@@AndreasSpiess OK, I'll look through your back catalogue. Thanks for the response

@stephanbrenner3317 2 роки тому

Thank your for the video. Is it really true, that super capacitors do not wear out? I have heard that they have charge cycles as batteries, but or course lasting a much higher amount of these.

@AndreasSpiess 2 роки тому

Theoretically, they should last forever as other caps which are charged and discharged a million times per second (at one Megahertz). But you are right, I also saw max cycle numbers which were probably not relevant for most projects because they were very high.

@jovaz0r 2 роки тому

This was a video I was waiting for. Silly enough I was using a booster / buck converter and didn't think of using a booster and putting everything parallel ...

@AndreasSpiess 2 роки тому

not always the first idea is the best. I also started with a buck-boost converter...

@mrksaccount123 2 роки тому

Extremely informative video, sir!

@AndreasSpiess 2 роки тому

Glad you think so!

@chrisv8674 2 роки тому

Always love your vids this one especialy. Missing highlighting the practical problem of over charging voltage, as they are extremely sensitive for over voltage ,even just a little will destroy the supercap and will make them leak.Many people that have a weather station from Davis have suffered from this problem.just 0,5 volt over a long period will kill the super cap,the solution was 2 caps in series,just take a higher capacitor value . I took me 3 replacements of the original before I found a artikel about over voltage ,and after that I never had a leak capacitor again.

@AndreasSpiess 2 роки тому

I agree with the overvoltage and I thought I mentioned it. This is why you also need this "balancing" circuit which also have a protection built-in

@johncoops6897 2 роки тому

@@AndreasSpiess - you certainly did mention it, but viewers might feel it came across as a "side comment" or "in passing", rather than something critical. Mentioned at 3:28 then about needing balance and OV protect between 8:13 to 8;35

@scurvofpcp 2 роки тому

These do pair well for lithium batteries in solar setups, you will need a separate balancer for your caps and it will end up being 2 caps in series for every lithium cell you have. But they can do wonders for helping your setup handle the higher starting current demands for some applications. I'll use this in RV's where weight is a concern, and yes, you will need 2 active balancers, which anymore giving the quality issues in lithium cells is almost a must anyway.

@AndreasSpiess 2 роки тому

Indeed, they are perfect if you need high initial currents.

@gslavik 2 роки тому

One more car application for super capacitors I've seen mentioned: Ability to charge from a near dead car battery and store enough energy to start the car (a smaller gas engine based car). Without having to pre-charge the super capacitor, the way you have to keep the backup battery pack charged.

@AndreasSpiess 2 роки тому

This is for sure possible. But probably a quite expensive solution compared with a standard Li-Ion booster.

@johncoops6897 2 роки тому

And both are far more expensive than a pair of standard jumper cables. Perfectly suitable for the very occasional (once every few years) that they would normally be needed. If you are repeatedly having to jump start your car, it is much better to repair it's charging system.

@111000100101001 2 роки тому

Thanks for the explanation and comparison. What about Li-Ion capacitors, how do they compare?

@AndreasSpiess 2 роки тому

I do not know. I never had such parts on my bench.

@MaDrone 2 роки тому

Interesting video, and clear explanation. Any electronic technician working before the digital era knew that high voltage "paper and oil" capacitors of several uF of capacity could maintain their dangerous voltage/charge/energy even for years, and that it was necessary to provide a parallel resistor to discharge them (resistance that during operation also served to balance the voltage in series configurations). An old high voltage capacitor "paper and oil", can be assimilated to a supercapacitor (the Coulomb is the measure of stored energy), only that in this case it would be necessary a DC DC step down converter to stabilize the voltage (of course, it is a theoretical speech, because involving high voltage creates many more complications). I agree that it is risky to compare batteries and capacitors, since the uses in which both can be used are few. In those cases, however, the capacitor could be the winner.

@AndreasSpiess 2 роки тому

As you describe, each technology has its use cases where they "shine".

@ashtentheplatypus 2 роки тому

I could imagine super caps being used for those deep sleep sensors with solar panels (like you said), but for locations that you really heckin' don't wanna revisit often, since the caps don't suffer from charge/discharge cycles. Maybe a satellite in space or on the moon, for example.

@AndreasSpiess 2 роки тому

I do not know if they are used in satellites. But a few properties of the super caps seem to be ideal for that purpose.

@wasserdrucker6227 2 роки тому

In my company we have some applications for Ultracaps: -Windturbine Pitch System Backup. A Box the size of 1..2 bottle crate stores the energy to turn back a blade at power failure once. Monitoring the capacitance by charge/discharge a little is much easier that with batteries and the last 20 years. -Fast Frequency Response for a few seconds until diesel gensets start up. -1MW for 1s UPS power to protect a whole factory or car paintshop. -Storage to provide virtual inertia. -Once my colleages charged up some caps with the wrong polarity. Because we do not give it to customer projects, but they are still working, electrified a kickscooter with 10x3000F cells. It drives approx. 1 km, which is good to travel between office and workshop. At the moment its charged for hours with a small buck converter from a small 24V power supply, but i have qick charging solution in mind...

@AndreasSpiess 2 роки тому

Nice toys you have at work. 1MW. Incredible! These are perfect applications for supercaps. Our projects, however, are very different. If you connect your scooter to one of your wind turbines it probably would charge faster, too ;-)

@AlienWacker 2 роки тому

9:40 .... I was actually thinking of this for a solar powered clock in my work's lunchroom... I have the caps, I have the clock... One cap, fully charged, will run the clock for about 23 hours... I just need to see if the solar cell can keep the cap full whenever the room is occupied (the lights go off when it is empty)... My big problem is that, Christmas Day & New Years Day my work is closed and empty, and the lights will stay off... For around (????) 24 ish hours...? I'll get around to it someday...

@AndreasSpiess 2 роки тому

I assume you would need to dimension the cap accordingly. Like the batteries in a solar powered outside project...

@christopherleadholm6677 2 роки тому

Thanks for the info.

@AndreasSpiess 2 роки тому

My pleasure!

@chiefgeek2020 2 роки тому

Speaking of simple circuits, what would use for detecting presence of 12v DC with an ESP32? I have considered optocoupler and voltage divider with resistors.

@AndreasSpiess 2 роки тому

A voltage divider is enough.

@Ole-vu9yj 2 роки тому

Please check lithium-titanate batteries (LTO). They can fill the gap between batteries and SuperCap. Advantages: - high current charge and discharge (~10C) - temperature range (charge/discharge): -50..65 °C - >20000 cycles (80% DOD) - safe, can't burn/explode like normal Li-batteries

@AndreasSpiess 2 роки тому

I compare them with LiFePo4 batteries where the low charging temperature is an advantage. Its disadvantage is the 2.4 volts where I did not see a standard charging/protection board so far.

@markday3145 2 роки тому

About 30 years ago, I (a software engineer) was working on a project intended for schools. We wanted a way to retain a small amount of settings (tens of bytes) in RAM when mains power was turned off. That was outside of school hours, but also 3 months of summer vacation. I think EEPROM or flash were considered too expensive. They didn't want the hassle of a removable battery. They probably didn't want the expense of a charging circuit for a rechargeable battery (which would also have to be removable, since the product would need to last many years). The hardware engineer suggested a large capacitor (multiple Farads). Alas, the project got canceled before we could see whether the capacitor would work.

@AndreasSpiess 2 роки тому

Soper caps probably would not have been a good choice neither because of their rather high leakage current. They are good for relatively short-term storage. The pack with standard caps would have been rather big and expensive, I assume...

@markottaway6899 2 роки тому

Excellent video. One of the hyped uses of super capacitors in weight, where they are lighter than batteries for the same capacity. Still not so useful in small projects, with the possible exception of airborne projects.

@AndreasSpiess 2 роки тому

I never compared the weight of supercaps with batteries. So good to know.

@SchoolforHackers 2 роки тому

Thank you, Professor.

@AndreasSpiess 2 роки тому

You are welcome!

@johnmoser1162 2 роки тому

What is the preferred solution if I want to have a 12v capacitor bank: Use Boot Converter (2.7V caps in parallel) or balancing/load managent (2.7V caps in series) ?

@AndreasSpiess 2 роки тому

2.7 volts is quite low and would create a lot of current if boosted to 12 volts. So maybe a few caps in series and a boost converter is a better strategy. But all depends on your needs. For a constant voltage you anyway need a boost converter as it showed in the video.

@nicholasbarker3577 2 роки тому

Thanks Andreas, I'm hoping for a supercap boost in my next e-car in Canada.

@AndreasSpiess 2 роки тому

I read that the Tesla Roadster aims for 1.2 sec from 0-60miles/h. I do not know if they use supercaps...

@bingosunnoon9341 2 роки тому

I worked in a shop that did a project that involved putting super caps in a city bus. I wish I could say it was a success but it wasn't. That was ten years ago. Hopefully, the current crop of caps are better suited for such an application. Anything to cut down on diesel smoke is worth a try.

@AndreasSpiess 2 роки тому

Maybe you were ahead of time 10 years ago. Here they at least start to replace diesel buses with electrical ones. They produce much less noise (and have many more advantages). Supercaps will be an exception in this application, I think.

@markxr1 2 роки тому

Good explanation. Here is a question: Can we store energy for these projects in higher voltage electrolytics, e.g. if we have a 63V rated much lower capacitance bank, say 100 000uF, theoretically its energy is nearly as much as the 60F at 2.7 volts?

@superdau 2 роки тому

Sure you can. But 100 000µF of 63V rated capacitors will take up quite a large volume.

@johncoops6897 2 роки тому

Looks like a maths fail to me: 100,000uF (0.1F) x 63V = "6.3" 60F x 2.7V = "162" which is over 25 time more. A 60F supercap is small, yet 100,000uF worth of 63V electrolytics would be massive. Andreas stated at 3:58 that the volume required for equal power is about 123 times The leakage of Electroytics may be higher too?

@markxr1 2 роки тому

@@johncoops6897 Isn't the energy stored in a capacitor proportional to the voltage squared?

@markxr1 2 роки тому

@@johncoops6897 But energy stored is proportional to voltage squared. But leakage might be a big deal. It was a thought-experiment not a serious idea.

@markxr1 2 роки тому

@@johncoops6897 Energy in a capacitor is proportional to voltage squared. But modern supercaps can maybe still do a bit better than electrolytics.

@mr.0x373 2 роки тому

Thanks for the great video!

@caffeinatedinsanity2324 2 роки тому

I am actually designing a project using energy harvesting and chose a 3 V, 15F supercap because I felt like it would be adapted for the charge-discharge scenario of my energy harvester IC fed by a solar cell. Not to mention my application, an ambient condition sensor, is very low-powered.

@AndreasSpiess 2 роки тому

I think this is a perfect match!

@liudas5377 2 роки тому

Great job. Thank you. 73s

@AndreasSpiess 2 роки тому

You are welcome! 73

@zyghom 2 роки тому

I found an usage for them: I built an UPS for my 4 servers on Raspberry Pi 4. The power supply supported by 8 x 500F super caps giving 5.4V - when 230V is gone, the voltage on these caps can keep 5A for more than 1 minute until it goes to 4.9V - this 60 seconds is more than enough to send "sudo poweroff" command to all servers. One issue: the caps are continuously leaking the current - even when fully charged - up to 0.5A from the power supply - so lots of energy is lost. On top of that: they discharge must faster the first 1V than the next 1V - but this would require boost converter - another power hungry device. After few months I decided to trash them (the caps - not the servers).

@AndreasSpiess 2 роки тому

I once made a video where I used a much smaller cap for the same purpose. But only one Raspberry, of course.

@zyghom 2 роки тому

@@AndreasSpiess I know, I saw, it pushed me to do it on a bigger scale so thank you

@bastiannenke9613 2 роки тому

They are also pretty great for undersized power supplies, charge slowly and use them when a lot of relays has to be turned on at the same time. I am thinking about using them for a emergency jump start box. Since they can push a lot of current and have a low energy density a handy crank or charging from a "dead" battery would be possible.

@bastiannenke9613 2 роки тому

@The Southern Cross but why should I spend 100€ when I could do it more expensive myself by buying capacitors costing more than a small box, overengineer the rest and add stuff due to featurecreep that I'll never use.

@AndreasSpiess 2 роки тому

If you are sure that your engine starts reliably fast, super caps are a good idea. Otherwise batteries are still needed. AFAIK they use super caps for lorry starter because they need a lot of current... Maybe good for my Harley (two cylinders, 1700cc needs a lot of torque to start), too

@bastiannenke9613 2 роки тому

@@AndreasSpiess off topic but I'm always impressed how often you answer to comments under your videos. I've seen year's ago a video here on UKposts where someone only had a 6ah battery (somewhere in that range) and a few big caps as replacement for the original battery. The small battery was only there to Keep the caps charged. It even seemed the vehicles started better with that bit of extra current. So it is definitely possible to make a jump start box with them. I don't know if lorries have them but it would really make sense

@AndreasSpiess 2 роки тому

You are right, I try to answer to all comments because I like the conversation with my viewers an I learned a lot with it!

@radarmusen 2 роки тому

Like the bus, think Switzerland also used gyro busses in the 60’ who else than professional watch makers would do that. :-)

@AndreasSpiess 2 роки тому

Indeed. A mechanical storage is very close to a mechanical watch. If the bus would have used a spring to store energy it would have been exactly like the watches…

@sirblingjax 2 роки тому

Andreas, what was the electronic load you were using to plot overtime the voltage and current. What software and what microprocessor where you're using to do that you electronic load test???? I seen something in the description of the electronic load test but when I click on the link nothing happens. Could you give us a more description of what you used?????

@AndreasSpiess 2 роки тому

Maybe you try the link again. I replaced it (and make sure you do not use an ad-blocker)

@virtualchannel5985 2 роки тому

La descarga de los condensadores se realiza de forma diferente a más baterías. A medida que se descargan va bajando volt. 12, 11, 10, 9, 8. En cambio la pila, mantiene sus volt Si hasta el final. Saludos

@AndreasSpiess 2 роки тому

You are right

@suny1265 2 роки тому

Well you are wrong ☺️. Skeleton Technology has made super Cap configurations that for the same volume of a 10 KWh battery they deliver 100KWh with supercaps. Technology is evolving

@AndreasSpiess 2 роки тому

Good to know. Let's hope that I am wrong and technology is faster.

@BeetleJuice1980 2 роки тому

Can you show if we can use supercaps in power supplies like linear psu or switching psu?

@AndreasSpiess 2 роки тому

There we use normal caps because the frequencies are higher (linear: 100 or 120 Hz and switching kHz to MHz) and we do not need extensive capacities.

@karljacobs794 2 роки тому

finally a video on capacitors i can finally understand how they work

@AndreasSpiess 2 роки тому

Glad the video was helpful!

@gaborungvari784 2 роки тому

thanks a lot for the 'super'-capacitor details :) !

@AndreasSpiess 2 роки тому

You are welcome!

@KM4ACK 2 роки тому

Great video! Thanks 😀

@AndreasSpiess 2 роки тому

Glad you liked it! 73.

@YOSEFPE 2 роки тому

i replaced in my dvm the battery with supercap with bust converter , its getting too expensive (and i got tired )to replace the 9v battery every few months , so ijjust give it a sec to charge , and i have the dvm for ~30 min work

@AndreasSpiess 2 роки тому

Interesting idea. Fortunately, the battery of my DVM lasts for at least a year...

@YOSEFPE 2 роки тому

@@AndreasSpiess lol maybe if you have automatic shutdown

@km5405 2 роки тому

i looked into using supercapacitors for powering a esp32 running from a coin cell. i came to conclusion its simpler and easier to get a lipo or li battery - the esr you'd need for esp32 is quite low, which means there arent any nice and compact ones you can find. ... supercapacitors are very good for pulsed power applications , my little 12V 20F capacitor bank effectively can put out like 1.5 kW pulses for about 1 or 2 seconds with 100W or less of input accumulating energy. ........ in the future if we get all graphene supercapacitors it might begin to be feasible as a alternative to batteries as in theory you should be able to store incredible amounts of energy in them.

@AndreasSpiess 2 роки тому

Thank you for sharing your experience. And I am sure we will get a lot of innovation in energy storage over the next years. It is needed...

@MPElectronique 2 роки тому

Hey Andrea, do you think if electrical appliances were built with tantalum caps ... they would last longer ??

@AndreasSpiess 2 роки тому

I do not know. But I know that tantalums are expensive...

@knoxpruett1889 Рік тому

Thank you for shedding light on the truth through all the hype !

@AndreasSpiess Рік тому

You are welcome!

@CryptonNite23 2 роки тому

There are some storage controllers with a backup battery made from supercaps. I'm using two supercaps in series to power a CMOS based clock if there is a power failure. The clock runs more than 1 hour with the caps. In some cases supercaps are fine :-)

@AndreasSpiess 2 роки тому

Nice project! I also used such a setup to safely power-down a Raspberry at power failure.

@CaptZenPetabyte 2 роки тому

What I am currently looking at trying with my EV project is using the SCs ability to dump a lot of current in a short period of time to create my own 'ludicrous mode'; battery charges the SC bank, SC bank pours current into the motors.

@AndreasSpiess 2 роки тому

I hope you will be successful!

@Hfil66 2 роки тому

As you suggested, the big breakthrough would be to be able to use higher voltages with supercaps. Battery voltage is limited by the chemistry used, while capacitors have no such theoretical limits, although they do ofcourse have practical limits, but it remains conceivable that some day the current practical limits could be overcome. The other technology you have not addressed is the use of flywheels (or even springs) to store electrical energy; although neither of these would probably currently be practical for micro-projects.

@NiHaoMike64 2 роки тому

I have seen a "rechargeable" batteryless radio that used a spring and a generator.

@1boobtube 2 роки тому

@@NiHaoMike64 radios can be such low power that no battery capacitor or any other power source is required. The antenna and ground is enough.

@1boobtube 2 роки тому

Hfil66, capacitors have very defined limits. Higher voltage means thicker dielectric which means lower capacitance. You could put 2 in series as noted, but by definition at half the capacitance. Note supercapacitors can be battery like and limited by their chemical changes used to store energy.

@Hfil66 2 роки тому

@@1boobtube Does that not assume that the dielectric of the material remains constant, that the breakdown voltage of the material remains constant, and that the surface area of the electrodes remains constant. If all these things remain constant, then the only way to allow for a greater voltage is to increase the thickness of the insulator. The earliest capacitors would only have an air gap between flat plates, and this ofcourse meant they had to have a significant space between the plates, and thus very low capacitance. We have come a long way since then.

@AndreasSpiess 2 роки тому

I agree with the mechanical storage. Another interesting concept (also not for small projects) is this one: ukposts.info/have/v-deo/oaSTq46EhKFzsqs.html

@silberlinie 2 роки тому

So, warum Andreas, bringt Tesla nicht einige wenige Supercaps zusätzlich zu den Akkus in die Konfiguration? Könnten sie doch wie du sagst, die allgegenwätigen Beschleunigung/Bremsungs Zyklen auffangen?

@AndreasSpiess 2 роки тому

Ich weiss es nicht. Ich vermute dass sie so viele Batterien parallel haben dass sie mit den hohen Strömen umgehen können. Supercaps brauchen immer auch Kosten und Platz. Vielleicht sind grössere Batterien wichtiger als Supercaps.

@robsycko 2 роки тому

How about use with high voltage solar system to store then charge a low voltage battery bank? I have a 300v270uf cap. that will hold some butt kicking power.

@AndreasSpiess 2 роки тому

Maybe needed if you only use small batteries which cannot support the full current of the solar panels.

@gosdeCarrer Рік тому

I have manage to build a weather station with just 2 supercaps of 5F (1.8€ each) and a mini solar panel of 0.6W. It runs without sun about 80 hours! It wakes up every 15 minutes to take the measures and send it with a NRF24L01 module to a gateway inside the house. It works pretty well. You don't have to worry about battery supervisors, over-charge, over-discharge, heating, low temperatures... I use an arduino pro mini without led/regulator, a boost to 5V and a LDO. With that I can use the charge of the caps from 2.7V to 5V. Even with weak sun it charges in minutes and survives about 3 days of no sun at all. Everything cheap and simple.

@AndreasSpiess Рік тому

Cool project!

@gosdeCarrer Рік тому

@@AndreasSpiess By the way, great channel and great work! I'm learning a lot, from practical tricks to the most technical topics. A nest of insane new ideas for a hobbitst :-) I'm new on all this electronics stuff since my times at the university long time ago, and I find this amazing and somehow much more available and powerful than before for a hobbist. And cheaper. And happy to see that the open source philosophy is also spreading here!

@AndreasSpiess Рік тому

@@gosdeCarrer You are right. I always say that I live in a "land of milk and honey" compared with when I was young (in the 1980s)

@sebydocky5080 2 роки тому

I see maybe another application for home solar application when switching from the solar inverter to the grid (for partial offgrid setup). During this switching, electrical microcut can occured and you can loose your internet internet connexion for example. So maybe such supercapacitors can be used to overcome these microcuts during few ms for devices such as intenet box, wifi router, raspberry PI, etc...

@AndreasSpiess 2 роки тому

Good idea!

@NiHaoMike64 2 роки тому

SMA uses large capacitors to do daytime backup without batteries. They're not supercaps, however, just large high voltage electrolytics.

@Monochram 2 роки тому

Parts just arrived, 2x30F 2.7V seem to pack quite a punch (fried some wires when shortened accidently). BUT I just noticed that Aliexpress Boost converters tend to have high minimum input voltage! at least 2V. The one you supplied has no tech spec on the product page; Anyone have a lead for a Low voltage boost converter capable of utilizing more juice out of the 2.7 Parallel caps?

@AndreasSpiess 2 роки тому

The typical energy harvesting chips are made to start at very low voltages.

@ianhill20101 2 роки тому

In lymens terms i think the more pressure on the caps plates the higher the charge rate they hold, Lto cells are a happy medium very temperature robust and 30000 cycles but we still dont reach the energy density of of li cells

@ianhill20101 2 роки тому

Absolutely love the mini hand and glove.

@AndreasSpiess 2 роки тому

AFAIK LTOs change their chemical structure and I would count them into batteries. But maybe I am wrong.

@devluz 2 роки тому

I am curious if this use case is possible with super capacitors: it charges up using a solar panel, boots up an esp32, sends out sensor data, then turns off fully again (not deep sleep). This could run a long time without an ageing battery.

@AndreasSpiess 2 роки тому

This is possible. I did it for my "Amazon Dash Button" project. The only question is: How to switch the MCU on (I used a mechanical switch)

@roboman2444 2 роки тому

They might be useful for driving an ESP off of a tiny solar cell during sunlight or overcast days. You could use a solar cell that outputs only a few mA of current in those conditions, and still be able to power the ESP's required >100mA for under a minute. They might also be useful for a non-stable power source. Like a solar cell that may get shade occasionally, or something that generates power from movement.

@zyghom 2 роки тому

did you practically try to charge a supercap from solar? just asking...

@AndreasSpiess 2 роки тому

I agree. They are good for relatively short-term energy storage in general.

@Luke-san 2 роки тому

As you said in the video, a supercapacitor and a small solar panel will do the job. Well I live in the Benelux. I have 2 panels in parallel which in summer give me a peak output of around 140 Watt. Yesterday at around 1pm I measured a 0,066A (shorted terminals) which leads to around 1 Watt of output. 1/140th of it's capacity. If we then use a smaller 5W panel and do the same math we are not going to get there I am afraid. There is a reason why I decouple all garden lights of their small panels here in the beginning of October and use a small dc/dc to charge them with the bigger panels.

@AndreasSpiess 2 роки тому

You are right. LEDs are not low power devices (micro amperes). BTW: I once made a video where I did all the necessary calculations for year-round solar projets

@user-qe7nv3bj3n 2 роки тому

Very good job.👏

@AndreasSpiess 2 роки тому

Thank you!

@robsycko 2 роки тому

What about use in conjunktion with lithium for surge protection

@AndreasSpiess 2 роки тому

I do not understand what you mean :-(

@ShahZahid 2 роки тому

also since they have very low internal resistance and thus can deliver very high amounts of current, they are also suitable for making a portable spot welder or if u just want to make things glow red hot

@AndreasSpiess 2 роки тому

True. But be aware that these applications need a lot of energy. I assume the caps are discharged quite rapidly and have to be charged if they are not huge.

@ShahZahid 2 роки тому

yes for the second one that is true, but if u use a decently sized super cap bank i think it should be sufficient for a spot welder also i think these can also be used to power the xenon flash lamps in flash lamp pumped lasers

@ing3888 2 роки тому

Is it possible to use the supercapacitors as a fast charging energy buffer before storing it into lithium batteries?

@AndreasSpiess 2 роки тому

Yes. But usually they are discharged right away to offload the batteries.

@JessGade 2 роки тому

I just discovered Lithium-ion capacitors. At a maximum voltage of 3.8V and low self discharge as well as long cycle life I think they are really interesting for solar powered projects. Ordered a few to play around with :-)

@AndreasSpiess 2 роки тому

Good decision. I show one of them in my mailbag video...

@JessGade 2 роки тому

@@AndreasSpiess I've received a 80F specimen (Fast Aliexpress delivery!) and made a little experiment: How many times can I deep-sleep cycle an ESP32 having the Lithium-Ion capacitor as the only powersource?: Turns out it manages 41 cycles of waking from deep-sleep (sleeping 30 seconds), connecting to WIFI and posting a MQTT message of the boot-count - before becoming unstable. After turn 41 the RTC-memory always return '1'. It manages to continue for another 17 cycles before stopping completely.

@olegariocamara9308 2 роки тому

Extremely useful video, I’m using super capacitors I’m my project in Brazil

@AndreasSpiess 2 роки тому

Thank you for your feedback!

@DmitryOrlov_dimorlus 2 роки тому

What about supercap in parallel with battery for decrease internal impedance of the battery during peak current consumption (for example transmission data through WiFi)? Did you have some experience with it? Is it helps to deeper discharge battery?

@Phoen1x883 2 роки тому

Would require 2 supercaps in series to handle LiPo voltage, and would only help with an extremely small battery that couldn't handle WiFi power consumption (and at that point, why don't you spend $5 on a bigger battery instead of some complicated thing with supercaps?)

@DmitryOrlov_dimorlus 2 роки тому

@@Phoen1x883 There is 5V supercaps, but this is exactly my question, I don't know if it makes sense or not.

@_bigbro 2 роки тому

@@DmitryOrlov_dimorlus why do you need a super cap? calculate necessary capacitance as I(current in mkA) / 2*time(in seconds) and result will be Cap in mkF.

@AndreasSpiess 2 роки тому

I assume it would work. But you have to pay attention that not the battery is charged in parallel to your load (using a diode for example). Otherwise, if you attach a load to this combination the voltage drops and the battery also wants to get charged by the cap...

@arthurmorgan8966 2 роки тому

What’s the fancy load tester with graphing you are using?

@AndreasSpiess 2 роки тому

Now I added a link in the description...

@jmr 2 роки тому

We used large capacitors in high performance car audio to deal with high drain the batteries could not support. Although I believe some people liked it when their headlights would dim during a huge bass drop. 🤣

@AndreasSpiess 2 роки тому

Interesting. I always thought that the car batteries are made for large currents. But obviously you had a more powerful audio system ;-)

@jmr 2 роки тому

@@AndreasSpiess I've seen car audio systems that cost more then a new car. Windows and side panels visibly moving. Some louder then jet engines. I'm not sure if car audio as a competition caught on elsewhere. I didn't enter myself but went to watch the competition.