I'm redoing an old 1972 Starcraft 16 deep V. I love how you've moved your your jack back away from the front. That solves a lot of my drainage problems. Im putting a 2 foot anchor pulpit so that frees up a lot of space for me.👍🥰🌹
@georgenettlesjr14664 місяці тому
A+ job my brother. I don't know why I was going to buy one when I could have done the same thing😅
@charliejones813510 місяців тому
Just bought a boat just like this one, those look great, Thanks
@jcusak11 місяців тому
Awesome job! Looks clean. Thanks for sharing. Will most likely copy it for my boat!
@freshonerestorationfabrica429811 місяців тому
You should definitely copy them. It's so nice to not have to crawl over the side. Worth every penny.
@autreyodom3607Рік тому
Man yea those are nice can't wait to build mine I have a welder an material thanks for sharing this.
@freshonerestorationfabrica4298Рік тому
Thanks man,Just bolted them up today.Painted them and also Grip tape on the treads.
@billwallenstein338726 днів тому
Nice work nice welds
@freshonerestorationfabrica429826 днів тому
Thank ya sir!
@ReedlaxationOutdoors7 місяців тому
These are awesome! Nice job!
@freshonerestorationfabrica42987 місяців тому
Thanks. They came out great and work really well. You definitely get spoiled using them vs climbing over the side. Should of done them years ago.
@BrokeBackBob4559Рік тому
Great looking steps and perfect design
@freshonerestorationfabrica4298Рік тому
Thank ya sir. They work really well.
@Mightiflier6 місяців тому
This is awesome; gotta use your design!
@freshonerestorationfabrica42986 місяців тому
They work great, you won't be disappointed
@Mightiflier6 місяців тому
@@freshonerestorationfabrica4298 thanks, will do.
@onat62Місяць тому
Çok başarılı bir çalışma. Merdiven profil kesit ölçüleri ve merdiven boyu lütfen.
@mokush4me4122 місяці тому
I have a 03 Ranger 185VS. I just ust showed this video to a small welding company in my area and the guy told me it’ll be about $1200 to make..😮 I didn’t say I wanted it gold plated.
@freshonerestorationfabrica42982 місяці тому
That's crazy, there's two or three companies that make them anywhere from 3 to 500. I saw them on a few vids and just copied what's already available on the market.
@murfrirhke45572 місяці тому
Very nice work. Hope ya had enough bumper clearance tho.
@freshonerestorationfabrica42982 місяці тому
More than enough clearance all around. Appreciate the compliment, they work well.
@yndalecioluna6081Рік тому
I would add a brace to the top winch area like you did the bottom for strength
@freshonerestorationfabrica4298Рік тому
Check out the finished version in my other video. They are super rigid and no need for additional bracing.
@whales302Рік тому
Super nice, I'm thinking of building one too. Do you remember the approximate angle you have your main tread post at?
@freshonerestorationfabrica4298Рік тому
I just cut them both at 45* was the simplest because the saw was already set up. Lol
@freshonerestorationfabrica4298Рік тому
I have a finished / installed video posted also. Check it out.
@whales302Рік тому
@@freshonerestorationfabrica4298 lol..been there :)
@claytonbrown26563 місяці тому
How long of Square tubing did you use
@freshonerestorationfabrica42983 місяці тому
About 3ft total between the main piece and the short that connects it to the tongue.
@ernestpaling5097Рік тому
I think it is too close to the boat. You are I. Danger of hitting it. Other than that, it looks great but do trim that bottom end as high up as you can. Nice werk!
@freshonerestorationfabrica4298Рік тому
Thanks Ernest.
@russellst.pierre6843Рік тому
Spray paint them and they will look store bought, great job
@freshonerestorationfabrica4298Рік тому
Thanks man. Check out my finish video on them. Painted and installed. Just need to plastic dip the handle.