Borzit Systems - the original handheld underground boring tool. Video instruction on how to bore a hole, ream a hole and add casing to your bored hole. Order your Borzit System at www.borzit.com Call us at 800-803-8738
КОМЕНТАРІ: 64
@des54443 місяці тому
Going into underground drop bury’s THANK YOU FOR THIS VIDEO!
@gmcjetpilot2 роки тому
For drainage I got an offer for $8,000 and they needed to go underneath my driveway. But instead of boring under the 25 ft wide driveway they wanted to break up the concrete and put down a new driveway. I mean that's ridiculous. I did it myself and was able to get underneath the driveway was a lot of work but far easier and cheaper than putting down a new driveway.
@edyriswanto94902 роки тому
Yes that is an equipment I need to install a tie rod to strengthen lateral force of earth eambankment
@vinnygoombatts14583 роки тому
I've been using this tool for over 10 years. It works okay, still a lot of work. The only suggestion I would make is we place brick or block under the drill pipe to help hold it up so you don't kill yourself trying to hold the drill level the whole time.
@Rodriguezfamily5122 роки тому
Where did you get the bore rods at?
@vinnygoombatts14582 роки тому
@@Rodriguezfamily512 Home Depot or Lowe's they are 3/4-in galvanized pipe you can buy them in sections 8 ft 10 ft 4 ft 2 ft you just add them on with couplings and the reducer goes on the board tool itself it's great you don't have to spend a lot of money
@googlny2 роки тому
Can it penetrate rocks???
@vinnygoombatts14582 роки тому
@@googlny Not big ones, it pushes aside baseball, grapefruit size fairly easily.
@ron42742 роки тому
That was my first thought. Got enough to do w/o trying to keep the pipe at the proper pitch & direction. Make a simple cradle that you can stake into the ground (fixed base) with an adjustable top (i.e., both front and back adjust side-to-side (for proper direction) and tilt (for pitch)). Steel for the base and wood for the top - fairly cheap & easy to make.
@anonymousbaros44248 місяців тому
Nice tool. Looking forward to getting one. Good demonstration too could do without the music though.
@marcelomateos34516 місяців тому
Looks good. I'm an irrigation contractor in Vegas, the ground is so hard here. This will make my life easier.
@nspro9315 місяців тому
We have one and broke couplings and threaded ends in heavy clay, and lost one bit. Switched everything to schedule 80 and extra heavy couplings and it was better but wish it had called for that ahead of time so we would not have learned the hard way. Also we had to turn the water up to "cutting flush" level, clay would not displace apparently.
@petromendoza47382 роки тому
Im a landscape contractor and we do a lot of sprinkler system installation. And sometimes we have to go under concrete slabs. Where can I get this set up. Can you send me the website or tell me where can I get one please. And you guys are awesome by the way! Great job!
@SP57802 роки тому
www.borzit.com Order online through the website or call M-F 8-5 mountain time 800-803-8738 Email to info@borzit.com Thanks!!
@maxamps453 місяці тому
would this work on masonry hammer drill?
@dineshpatel5643Рік тому
Praise
@GeckoCycles3 роки тому
THE MUSIC!!!!!!!!!!!!!!!!!!!!! i WAS WAITING TO HEAR SOME ONE FRICKEN TALK
@SP57803 роки тому
Oh man, I'm sorry! Let's see if we can do something about that.
@jasonyeh997 місяців тому
Do people know if this business still around? I ordered a boring kit from their website over a month ago but did not receive the tool from them. I called many time but no answer and can’t leave messages, no email reply as well.
@juanbarrera76232 роки тому
Me gusta como puedo tener más información del producto
@F22DogFighter12 роки тому
How can I attach 1” IPS pipe to the end of the bit or pipe to pull back? Any type of swivel needed to spin and pull back?
@SP57802 роки тому
You can remove the bit, and attach your 1" pipe to the 3/4" pipe using a reducing coupler. Spin the drill clockwise to pull it back through the bore.
@JRM1371Рік тому
What's the total boring time for that 45' run? Not setup, just the run time from start to finish? Looks friggin ingenious! Tell me something good and you'll have a new customer! 😁
@mikejanczura15402 роки тому
Nice in theory. I bought a kit...it's good for loamy sandy soils.. The main hub needs alot more attention. Mine broke within 20 minutes. 😥
@SP57802 роки тому
Not sure what you mean by "main hub." Borzit does have a warranty. Email to info@borzit.com for repair or replacement!
@philippetays4263Рік тому
this would work good to put a new water line into my basement but how am i going to hit the right area in my basement
@user-Sejkiv10 місяців тому
Класс.
@latiffesa3 години тому
Please sell in Malaysia
@ryanchristopher59062 роки тому
Need to turn up the water to push back the cuttings
@SP57802 роки тому
With the Borzit system, the cuttings are not pushed back out of the bore. The water is used to moisten the soil so that the bit can compress the cuttings into the wall of the bore. Too much water can cause the soil to collapse around the bit. The system actually requires very little water pressure.
@arnoldrodriguez63003 роки тому
What kind of drill is that?
@SP57803 роки тому
I believe it is a Milwaukee "Hole Hawg". That is the drill that we were using when those photos were taken and is one of the drills that we recommend.
@scottwillis54342 роки тому
Great tool! Looks like it's intended for fairly hard, stable soils. Any suggestions for looser or sandy soil? Less or quieter music, please. Loud "Oh, a oh, a oh, a hah ha Oh, a oh, a oh, a hah ha Oh, a oh, a oh, a hah ha" gets old quickly. Oh, a oh, a oh, a hah ha. 3:35 please increase dwell time of the text.
@nspro9315 місяців тому
They show a bore with casing at the end of the video.
@rosaliebanega5622Рік тому
Is that available in the Phil how much
@SP5780Рік тому
$239 US plus shipping. We ship anywhere that can receive USPS Global priority mail.
@motionman0Рік тому
Is this company still in business? I have been calling and it goes into voicemail.
@SP5780Рік тому
Hi - yes still in business! If you would, can you email me at info@borzitcom and I can send you my direct phone number, or I can get right back to you. I'm so sorry the voice mail hasn't gotten an answer for you. Thank you!
@javiertovar9522 роки тому
Where can I buy it
@SP57802 роки тому
wwww.borzit.com - this is our website and it can be ordered online
@dineshpatel5643Рік тому
Keta mitar kam kare
@kpandi97662 роки тому
How to get in this machine in India.
@rajajasti56382 роки тому
Wher to get this machine in India or how order to company
@SP57802 роки тому
@@rajajasti5638 we do offer shipping overseas via USPS global priority mail.
@sapnatomar7814Рік тому
Prize in India
@gristdarren3 місяці тому
I'm guessing the fact that because they think that their tool is good, it completely negates the need for any type of personal safety gear. That drill will rip your hand off and not apologize... Not trying to be a dick, but no gloves, no safety glasses???... Can't really see their boots to know if they're steel toe, but maybe I'm just getting to old... Or I've been brainwashed into thinking that you need safety gear everyday for every job...
@leifjernigan48563 місяці тому
You have indeed been brainwashed the only danger is that drill getting stuck and breaking your wrist and gloves won't stop that
@KiD_CuDi93 місяці тому
Not wearing gloves is the safest thing you can do here bud. If you were to have gloves on and you grab the the rod while it’s spinning, best believe your hand is going to get caught in that. Only speaking from experience. When I first started working in jobs similar as this one, I would always wear gloves until I was advised not to. Haven’t worn gloves ever since. Now the not wearing safety goggles part, rocks don’t necessarily come flying at you so no need for that either but to each their own.
@diegovega65452 роки тому
I'm a plumber and that milwaukee drill if you not careful. It can broke you wrist real easy. Very dangerous drill.I don't like it. I hate it!!!!
@valentin13212 роки тому
Whats a better alternative?
@SP57802 роки тому
The Milwaukee drill is just one option. You can use any industrial type drill that has a 1/2" chuck, a power rating of 7-9 amps, and turns a constant speed, not variable. Variable speed household-type drills are not powerful enough to push the pipe through the bore.
@harryrodriguez8932 роки тому
Probably need to muscle up.
@diegovega65452 роки тому
💪😎
@scottwillis54342 роки тому
If it's powerful enough for this job, it's going to be dangerous.
@WilliamBrown-oc8or3 роки тому
.
@joek43874 дні тому
Do not order this. I ordered one 6 months ago. I have not recieved it yet! I have left several messages and emails.