An Expensive Smart Home Mistake? My Quinetic Switches are FAILING!

День тому

For the past 7 months I've been using kinetic wireless switches made by Quinetic coupled with a custom receiver as part of my smart home lighting setup. However, one of my switches has now failed and another appears to be about to imminently fail in the exact same way - have I made an expensive mistake by installing these throughout my home? In this video we'll take a look at the failure and also take one of the switches apart to see how they work.
www.camerongray.me/
/ camerongray1515
Chapters:
00:00 - Introduction
03:40 - How Has it Failed?
07:37 - Tearing a Module Down - How Does it Work?
13:58 - What Do I Do Going Forward?
14:34 - Can These Be Relied On?
16:13 - Conclusion
AFFILIATE LINKS NOTICE:
Product links under this video marked “(Affiliate)” are affiliate links where I may receive a small commission on qualifying sales. Affiliate programs that I am a member of include, but are not limited to: Amazon Associates, eBay Partner Network and AliExpress Affiliates.
As an Amazon Associate I earn from qualifying purchases.
Purchasing through these affiliate links will not cost you any more money, however the commission earned significantly helps fund the production of videos on my channel.

КОМЕНТАРІ: 63

@klaernie 5 місяців тому

I would really press the manufacturer for delivering a product with defects. At least they should keep supplying you with new modules until your warranty runs out.

@camerongray1515 5 місяців тому

They have a 3 year warranty (I think) so realistically I could definitely get them replaced, but then I need to factor in the time I'd have to spend dealing with returning modules when they fail and the inconvenience of them failing at inconvenient times. Would rather just replace them with a system I can trust the reliability of.

@klaernie 5 місяців тому

@@camerongray1515 I totally get your sentiment. But even if you switch, I'd hold them accountable and force them to loose money on your original sale, since that behavior must not be tolerated.

@TheSpatialTheory 5 місяців тому

It's also possible that future revisions may have additional support added there. Those really seem way too small for the forces involved using that kind of plastic

@georgeprout42 5 місяців тому

@@camerongray15156 years under UK consumer law (5 in Scotland, they always like to be different) covers manufacturing defects or design faults for a product that should be reasonably expected to last that long. But I understand that the hassle factor comes into play. Them offering 3 years is nothing more than a marketing tool, it's still 6.

@leeroyfairhurst3883 5 місяців тому

@@camerongray1515 - The more items that are returned/highlighted will improve the production from suppliers.

@alanjrobertson 5 місяців тому

Have you contacted their customer service dept? It looks like a clear design flaw and they should supply you with replacements, hopefully of versions with a more robust design...

@movax20h 5 місяців тому

Oooo. Cool. I knew of Quinetic switches, and was liking the general idea, but then was not thrilled by lack of receivers so I can hook things into own system. Your reverse engineering efforts then are a game changer, and now I will look into this again. Rest of my home automation is primarly Shelly Pro modules, with custom automation software. I do not think this is planned obsolescence, just a design mistake, possibly because product is pretty new and made by company with a bit less experience. Switches are designed to last decades. I think it is fixable, both in design iteration, but also if it fails, to use some epoxy to glue things back.

@jackipiegg 5 місяців тому

14:43 I do this with zigbee coin based CR2032 switch (AQARA) and solder the switch points to an existing wall switch. No live wires.

@garethblake544 5 місяців тому

I must admit like yourself l had concerns when l first saw these Quinetic switches being installed as a primary switching source on their longevity considering the replacement cost in the advent of a failure as you have just highlighted. Keep up the great videos and stay safe.

@danr3199 5 місяців тому

+1 for Shelly switches. I have Plus 1s, Plus 1PMs and Plus 2s in all the light switches in my flat with cheap Schneider retractive plates (and a couple of MK-type grid ones). All the usual light on/off happens locally, but you can also do it detached and handle switching logic remotely. Of course it relies on having neutrals at your switches, but your place should be modern enough for that. I do all the comms between Shelly and Home assistant over MQTT, bit of a pain to set up but happy to share config files if you need a hand

@alerighi 5 місяців тому

The thing is that Shelly (or other) devices needs to be powered. And if you have one or two, not a big deal. But if you have an house full of them the power consumption starts to be significant! I've measured that 1 Shelly devices consumes roughly 1W of power. That is to me a lot. If you multiply for 20 switches in an house you get 20W of power consumed just doing nothing. At the end of the year it is 175kW/h of electricity, that at the price of 0.30euros in my country is 52 euros at years just to run them. This is also an environmental problem also, I don't like wasting electricity for nothing.

@danr3199 5 місяців тому

I have 20 Shellies now (in a 2 bed flat…), and found that out of the box they use about a watt, but in eco mode (not sure why this isn’t a default) they use under 100mw each, with no noticeable difference in speed from my usage. The energy prices here in the UK are around the same (mines 30p/kWh day and 7.5p/kWh night), but I can cope with the £5/yr ish for the convenience. Not to mention it saves me more than that through automations like turning everything off when I leave home.

@seanhood980 5 місяців тому

I've been looking into using the CSPGM2075PW modules from Click. They're a Tuya TS0042 internally but a grid switch externally. Also supported in Z2M. Reason I haven't yet is mostly down to price.

@skysurferuk 2 місяці тому

"Just because it's a brand name, doesn't mean it's good!". I wonder who said that? Great information, thanks. 👍

@TelcoGeek 5 місяців тому

Definitely recommend Shelly. I’ve got a bunch of lighting and bathroom fan circuits now controlled by these with MK retractable switches. Works a charm. Much better than Sonoff in my experience.

@davidnorth1021 5 місяців тому

I have the BG Nexus compatible Qunietic grid modules - two in service for just over a year now. Might check on their construction before I buy more!

@MartinE63 5 місяців тому

They have a three year warranty, which I’ve had to use just once, after around two years with a heavily used switch. The MK grid switch failed to click when pressed, the same problem as you had.

@VW_Fan 5 місяців тому

I would love to see a Shelly video. I am using a couple of these with a view to get more. Would be good to see your views on these and how you implement them.

@trevelvin7455 5 місяців тому

Interesting video. Is this a bad batch or has it happened more frequently?. Have you spoke to the manufacturer about it?. Love the detail of your videos btw.

@jasonlee3247 5 місяців тому

“And in my next video I’ll be installing a brand new Philips Hue system in my flat” 🤣

@wiideathmodtv 5 місяців тому

@Cameron Gray it may be quicker to 3d print a new case then switch platforms?

@relativenormality 2 місяці тому

Just installed one of these in the Knightsbridge Grid version to solve an isolate problem - hope it lasts!

@tbavister 5 місяців тому

1. Warranty return. 2. Hard to work out how much space and the movement of the mechanism but: could you drill two holes and put a long skinny bolt across the width to act as the limit?

@iambueno 5 місяців тому

I'm using Candeo zigbee modules along with the Click minigrid system. No issues at all with Click, they make great products, the candeo stuff has been rock solid too. I also have a bunch of Sonoff zbminis which I use with click rocker switches, and also to control extractor fans.

@Alex-if3sr 3 дні тому

People are becoming lazier by the day. How hard is it to turn off the switch by hand? Nice video on the teardown though

@iambueno 3 дні тому

@@Alex-if3sr sorry dad!

@MrLatte27 5 місяців тому

While it would be better if it didnt break in the first place it is fixable, put a small screw through the side of the plastic housing to hold the spring down problem solved.

@MrDead1975 5 місяців тому

the aqara switches are nice I use the H1 no neutral all over my house but they also do neutral and wireless versions. the old baking soda and super glue trick may work to rebuild the broken plastic clips in your switches

@Banzahair 5 місяців тому

But they are some times a bit temperamental of not connected to a good coordinator Had trouble with the sonoff ones but better stability with Skyconnect

@shaunb8211 5 місяців тому

Been running a house full of these a year and had one fail a couple of weeks ago, exactly the same issue!

@andrewmcewan9145 5 місяців тому

Looks like there really simply designed. You can likely add some diy reinforcement to the posts if there easy to pop open like that. Really dosent bode well for bigger installs/important installs like you say. I really like the kentic consept.

@rosspage9397 5 місяців тому

Im doing a significant rennovation of my home including a full rewire. Using shelly 4pro in a custom cabinet and then shelly i4s to 2 dual pole retractive switches. Plan is to use HA to enable my switches to do different things such as blinds, lights etc... A shelly plus 2 would do a similar thing for standard wiring setups. Would be interested to see how you find the shellys.

@MrDead1975 5 місяців тому

Aqara H1 switches allow multi button options when you run in decoupled mode, single clicks, double clicks and. multi press in 2 gang switches so you can control multiple devices through home assistant

@mercian8051 5 місяців тому

If you’re doing full rewire, I wouldn’t recommend using wireless lighting. There are loads of wired solutions available

@Fleeeeg 5 місяців тому

I've had shelly 1 modules for several years, recently the capacitors in the power supplies have started failing and they make a loud hissing noise

@camerongray1515 5 місяців тому

@mercian8051 The way I'd handle this situation is to at least wire for regular switches and then install wireless switches if desired. That way you can easily enough convert back to wired switches if desired. With a rewire, it may also be worth running additional cables such as running some switch wires to a central location and some sort of data cable such as KNX to each switch position. Even if they never end up getting used, it's better to get them in at rewire time rather than need to add them in later.

@paulhyland3528 5 місяців тому

I did something similar for lighting all my circuits wired to a central location, I used pro 2s been in over yr and all good

@scottphillips7267 3 місяці тому

Can surley Retro fit a metal clip around the switch maby ?

@CarltonDodd 5 місяців тому

As someone mentioned already, could you repair these with tiny screws through the outside housing with the ends catching the spring, like the clips do?

@camerongray1515 5 місяців тому

I imagine you probably could, but you'd have to be extremely precise to get the positioning just right - the mechanism only moves around 1mm when clicked. Personally I'd rather just replace them with something I can trust the reliability of

@ryang6572 5 місяців тому

This is like watching a big Clive video

@MikeSmith-tx2lp 5 місяців тому

I avoid BG if possible. Low cost for a reason. Had a real hassle installing one of these in a grid, needed supplied adaptors and shims, a real cobble up and ended up looking crap. The Quinetiq stuff I’ve found to be robust.

@Cook1eMR 5 місяців тому

Really disappointed to see these fail. I had this ear marked as an in bathroom solution. Seemed ideal for wet zones considering no power. Do you have ideas for alternatives?

@zusurs 5 місяців тому

Can't this be fixed with a simple drop of two-component epoxy? It should add necessary mechanical support for the failing plastic clips and keep the spring in place.

@camerongray1515 5 місяців тому

I did consider this but unfortunately the spring needs to be able to move downwards when the switch is pressed but be held under the clip so epoxying it in a fixed position wouldn't work.

@TheSpatialTheory 5 місяців тому

I think they were suggesting a drop be placed on top of the tiny clip before it fails to provide additional resistance against shear forces

@zusurs 5 місяців тому

@@TheSpatialTheory Yes, thank you for clarifying what I meant - I indeed suggested to use epoxy as a support filler to prevent the plastic clip from breaking off so easily, not to glue the spring in place.

@NicksStuff 4 місяці тому

Surely, with your set of skills, you'll DIY a solution to reinforce those two little plastic posts

@camerongray1515 4 місяці тому

I probably could have, although personally I always try to use things where I keep the hardware as stock as possible, and if the manufacture's design isn't good enough from the factory, I'll not use it. I'd rather not be in a situation where every time I want to fit a new switch I need to embark on a project to reenforce them.

@toddmcgowan9449 5 місяців тому

Do the Quinetic switches come with a warranty? It seems like a seven-month-old switch should be replaced by the company.

@camerongray1515 5 місяців тому

They do, and I absolutely could have used the warranty, however my point was more that I have installed a tonne of these and now can't trust them to be reliable long term. The £17 to replace a failed module isn't really the issue, it's the time and effort required to deal with failed modules where I then can't control the lights and need to swap the module and deal with the replacement process. Even worse if you were installing this as a contractor and need to deal with customers calling you back to replace failed modules.

@toddmcgowan9449 5 місяців тому

Thanks for your quick response. I loved your video. I installed Insteon light switches 10 years ago and not only did they start failing about a year out, the company went out of business! I must have spent close to $7,000 on those darn things. I’ve been replacing them with Lutron switches.

@unifytechuk 5 місяців тому

I believe the spring is part of the energy harvesting system that turns the kinetic energy into electrical energy

@chrisfox3161 3 місяці тому

I sent mine back to TLC under guarantee. Replaced without fuss or arguments.

@camerongray1515 3 місяці тому

I definitely could have done, they'd still be under warranty but given I'm pretty sure this is more of a design issue, I'd have ended up with new switches that could fail in the exact same way again. At that point I'd rather just cut my losses and fit a different system which I can trust the long term durability of.

@chrisfox3161 3 місяці тому

Fully understand that stance. However, informing the supplier of the issue may result in action to rectify the problem. If you don't know it's broken you can't start to fix it.

@gabest4 5 місяців тому

Maybe pour a blob of epoxy on both clips to strengthen them?

@Irilia_neko 5 місяців тому

It's time to use the warranty

@camerongray1515 5 місяців тому

If I hadn't ripped it apart for a video I would have, however, I'd still be reluctant to rely on these as I'd find myself needing to make warranty claims every time one fails and have to deal with switches that I can't rely on not to fail at an inconvenient time.

@Irilia_neko 5 місяців тому

The kinetic switch is not the problem, the only problem is this brand, just use another brand

@camerongray1515 5 місяців тому

The issue is that there only seems to be this one model of kinetic switch that fits into my MK grid light switches. Another company (Ener-J) also sell one, but it looks very similar and may end up being the same product under a different brand. Would rather just replace them with a system that uses the known-reliable MK retractive switches. Then, while I could get the traditional "paddle" style kinetic switches - those are out of the question as I want something that matches my existing light switches.