Configuring the Behringer FCB1010 with the Line6 HX Stomp

4 роки тому

I was looking for a way to utilize the Behringer FCB1010 MIDI controller to act as more of a pedal board for my Line6 HX Stomp. This video will go through a high level of how to program the unit to work with the HX Stomp.
A couple of references that I mention in the video:
Mountain Utilities - FCB1010 Manager - This is the free software that can be used in conjunction with a MIDI to USB cable for programming your FCB1010. I personally found the software useful for displaying a layout of how I wanted my board to be configured.
mountainutilities.eu/fcb1010
FCB1010 Full Tutorial - • Behringer FCB1010 Full...
FCB Manager Tutorial - • FCB1010 Manager Tutori...
HX Stomp Owner Manual - line6.com/data/6/0a020a4010c9...
Page 49 is the page with all of the CC codes of importance for programming your FCB1010.

КОМЕНТАРІ: 11

@cedricBUNKERTON 4 місяці тому

I've watched 15 videos on the FCB1010 but yours is the first to give me the information I am looking for - thanks

@chrisheilala8233 4 місяці тому

I'm glad to hear that this video has helped you out!

@JayQuijada Місяць тому

If you don't want to use a block for your expression volume, just assign the volume parameter in an 'always on' block like the amp or a compressor to your expression pedal, give it a min value of around -18dB, because if you go 0% to 100%, the smallest variation in the position of the exp pedal will be huge.

@AlexandrePiazza 4 місяці тому

Hey, man! I found a way to use the expression pedals without adding a specific block. You have to use Stomp's Learn function. You can set both volume and effects: Wah and pitch, for example.

@adg2011mm 4 місяці тому

how?

@AlexandrePiazza 4 місяці тому

@@adg2011mm you set a Midi value on the exoression pedal from the Behringer and set this pedal to control the volume at the end of your chain (in HX). You can acess this volume true the circle at the end of the chain. The problem with this method is that you need to set this for every pre-set you have. But it works.

@AlexandrePiazza 4 місяці тому

you kind of use the output from the HX as a volume pedal

@lawrencel500 Рік тому

How do you control the wha with the Exp pedals of the 1010?

@adg2011mm 4 місяці тому

FCB1010 with hx stomp Set midi channel to 1 on HX and FCB Expression Pedals Bank 00 (or whatever u want) Hit the FS you want to program Hold DOWN button 3 sec hit up button (confirms edit mode) Need ONLY fs 8&9 with solid led (press and hold them to get there) press 8 so it blinks press up to confirm select CC number. Can be whatever you want (need to set it on helix) press up to confirm Set low value of 00. press up to confirm press 9 so it blinks press up to confirm select the CC number you already set press up to confirm Set High value of 127 (high and low can be swapped to reverse it) press up to confirm hold down to save and exit edit mode.

@gtrdaveg 3 місяці тому

Jesus, this thing looks like a massive pain in the arse! Can it send multiple messages per pedal? Ideally, I'm looking for something that will control my guitar fx and a DMX controller *simultaneously*, ie when I hit pedal 1 the distortion kicks in and the stage lights change, for example. Is that doable on this?

@chrisheilala8233 3 місяці тому

It's not bad once you understand what is going on...There is a learning curve, but the satisfaction of getting it to work the way that I wanted was worth it for me. I no longer have the FCB1010 or the HX Stomp, so I can't directly answer your questions from experience, but based on what I've read, it does look like the FCB1010 should be able to handle sending multiple MIDI commands at once.