So many technicans are quick to fire parts at customers vehicles without evidence from diagnosis, whether that be simple visual diagnostic or more complex diagnostic with a multimeter. This was literally charged out as a strainer filter and a hell of a good exsplanation of what I found which resulted in a nice quick turnaround for the customer and a short video for me 👌

Thank you for the comment. Glad you enjoyed the video I wish it was a bit longer and a bit more detailed but I'm glad you got something from it 🙂

Hey hsam, I'm good, thank you 😊 are you okay?

@@TRUCKTECHUK I need help from you

@@hsamatwa749 what seems to be your problem?

Thank you for the comment😎 I hope it helps you along the way

Thanks for the comment 😎........ not all hero's wear capes 😂👌

Thank you for the comment 😎👌 Yes Id like a electric pump for the priming engines and I'd like a MERCEDES style cab tilt pump that's electric too 🤣🤣🤣👌

Thanks for the comment from across the pond ❤️. I see a large mix of mx-13 and mx-11. I think the amount of issues we have had with the camshafts in mx-13 engines, owners who have mx-11 engines must so glad the have overhead camshafts 😂. In regards to the unit pumps and crankcase ventilation units I know we have them sat on the shelf in work......I will check the factory Monday to see what the stock levels are just incase we're heading for another shortage of parts like we had with the VTG actuators awhile back. I'm glad your enjoying the videos 👌😎

@@TRUCKTECHUK Interesting, we never had any issues getting VGT actuators which for most part are root cause of random E-CAN codes. I have EUP's on order since January, OCV since May. Keep pushing expected arrival back. PMCI (ECM) have been on backorder for long time also. I know of a guy sending them to your area to get them fixed. My fleet has never experienced a cam failure on the MX13. I think the lower temperature oil temp thermostat campaign helps the issue, but we don't run the extremely lengthy oil change interval and still run 15W-40. Two fleet that had cam issues around my area (one delivers packages in brown trucks) both ran the long oil change intervals and 10W-30.

@@stevesauerland223 what is the mileage of trucks using 15w40? We use only 10w40 DAF engine oil on mx 340 and mx 11&13 engines. Here we have 4 seasons and it happens sometimes to change camshaft because of cracked tapped roll on pump or valve. Dislike the fuel filter o-ring seal. It’s EPDM or smth like that and have to change every time when you loose the cap.. The video strikes again buddy. Regards 🎉

@@preslavvasilev7387 We run Paccar from MY 2012 all the way to MY22 and some Cummins/ Caterpillar that still require 15W-40. We have over 800,000 miles (1,287,000 KM) on many units and run 25,000 mile Oil change interval on tractors, 12,000 on dump trucks. Currently use Shell Rotella T4 15W-40, but for years used Phillips Guardol ECT 15W-40 but is "shortage" of it. I have had EUP failures with broken spring/damaged lifter, but anti-rotation pin usually shears and EUP bolts breaks so doesn't damage camshaft. Cam failure I was referring to was EPA17 with pressed on lobes. Interesting how cam failure increased when they switched to variable displacement pump and lower oil pressure.

hello bro how are u doing,how can I get in though with you pls

Hi, thanks for the comment. I've not worked on one of them for years and I can't remember the last time I changed a V-belt sorry. I don't do servicing 🤷‍♂️

Thank you for the comment 👌

Hey Chris thanks for the comment. I had a few vehicle's do this before and the only way I've been able to identify it is to run tests on the fuel system to identify discrepancies in fuel system components to try and prevent the truck failing in service....which no opperator wants. 😐 how old is the vehicle?

@@TRUCKTECHUK is 65 got 6 c.f. 3 with lights on put a pump on this this one 3 years a go cause there were Ali fillings in pump when I stripped pump down looks like roller bearings have dropped and caused it to grind in pump causing this to stop when not under pressure when left for a bit would start back up again

Chris if you are stuck with them and want a more definitive answer on what has gone wrong running a high-pressure pump test should identify your issue. If want to contact me please do so on my contact page and we can try and get to the bottom of it quickly for you

Ok mate took it out lights gone out just seen mate at daf and got some primer filters just in case also I have fuel pump spare will run this week with open eye you every come across p153b active and p140einactive saying crankcase ventilation rotary speeddata valid but to lo least severe just built c.f. tractor camper go in round Scotland end of month but unsure if was going to be problem with engine light on

Good good. Chris, I have got a video on crankcase ventilation units if you want to see what can happen and what's you need to do to change them depending on type fitted.If you have the new type Cummins crankcase ventilation unit fitted you can get a repair kit for it now 😉

Нужно заменить в первую очередь самое простое это фильтры. Фильтр адблю элемент и маленькую сетку, топливные фильтры и воздушный фильтр. Потеря мощности может быть из-за нехватки воздуха, это забитый пылью воздушный фильтр, а так же нарушена герметичность интеркуллера, забиты топливные фильтры не достаточно подаваемого топлива. Возможно обратный топливный клапан не достаточно создаёт топливное давление пропуская его в топливный бак. Если это не решает проблему, то можно замерить топливное давление механическим манометром, к сожалению значения я уже не помню. Из маловероятных причин попали сторонние предметы в бак и забили заборник топлива, нитки, тряпки, пленка которые могут находиться где-нибудь в топливных трубках. Не достаточная подача топлива, износ насоса низкого давления либо где-то происходит подсос воздуха, нарушена герметичность топливной системы. Плохое качество реагента адблю, дизельного топлива. Самое последнее вышла из строя турбина, нужно замерить ее нагнетаемое давление, либо визуально проверить сняв с выхода интеркуллера резиновый соединитель и в нем посмотреть наличие моторного масла. В машине есть заслонка горного тормоза бывает так что она заклинивает и на половину закрывает трубу выхлопных газов, что затрудняет проход отработанных газов которая в свою очередь ограничивает тягу.

Thank you for the comment👌 To answer your comment I would say your refering to the driver performance indicator www.google.com/url?sa=t&source=web&rct=j&url=wwwnordictruckce.cdn.triggerfish.cloud/uploads/2017/01/daf-driver-performance-assistant-64739-en.pdf&ved=2ahUKEwiK6quo5KD6AhVMEsAKHchnAHQQFnoECA0QAQ&usg=AOvVaw1Euwlw0I5GZY7_M2LgnEcN

Thanks for this 👍

Hey thanks for the comment 😃 I love the Milwaukee grease gun not that it gets much use anymore, but when I bought it the output pressure was the same as the M18 but with out the light and half the price so it was a good purchase for doing car transporters with 30+ grease nipples lol

always seem to come in batches these faults don't they! it's AMAZING how people can't follow simple instructions on changing filters especially the damage it can cause to the fuel system with the tolerances being so high now for fuel system components. in regards to the water separator have you noticed a pattern on where the vehicles have been filling up i.e at service stations or bulk tanks in the yard?

@@TRUCKTECHUK we do not get any water issues where I am ..lol..but I do get annoyed with people and filter changes as they know in our place anyway that they won't get the fault to fix so they don't care..and no way will they follow the procedure for the ngd

You say about people not getting the fault to fix, we were discussing people being "quiet quitters" and also "quiet firing" (that's a good read). it took me being a workshop controller to realise not everyone wants to be a master tech, some people want to just come to work .....tap wheel nuts and go home and I'm fine with that but if they don't want the complex jobs they should still work to a basic standard. Maybe I'm sad but I will help anyone from apprentices to random people who ring the dealership for advice If I can help someone do a better job or understand something that makes my day but please meet me half way with WANTING TO DO THE JOB. My favourite I hear is "I don't get paid enough to do that" 😑😑😑😑😑

@@TRUCKTECHUK The i don't get paid enough is a "i don't know what i'm doing "..I did the very first Master Tech waaaaay back in 2009 ..Back then it was a big thing ..Some people don't want to know ,that is their excuse for getting out of work ,and some are just totally incompetant..I find when you advice someone for example to use gauges ,it isn't what they want to hear so they won't use them and spend more time just randomly condeming something that is not in stock hoping someone else gets it and then have to fix the issue ..Don't get me wrong most people have strengths and weaknesses ,and you NEED that person who is happy chapping nuts and bolts ,as much as you need those who would rather get their teeth in to problems..But for some it is a job they fell in to ,not something they wanted to do when they left school...And people for some reason will not use RMI ...IT ISN'T PERFECT but it is yes or no lol..Had a lad change sws and a clock spring still had the same fault 14 hours later so i got it looked at some diagrams fuse for clockspring had popped 15mins ..and after the roadtest and turning the steering full lock to lock in the yard all ok ..i will say the workshop who brought it in had been on it for 14 days lo

@@TRUCKTECHUK Workshop controller is the most thankless job in the trade ..We are looking for a new one just now ,no one wants it

Thanks for the comment. Unfortunately, I've only ever used paccar as the fittings are very specific. I've been able to source a kit with a gauge that does both negative and over 8 bar pressure positive pressure for the paacar engine, but the price is £120 plus shipping which I didn't think was too bad considering the price of the paxcar kit is over 500!

Love The videos , the diagnostics are great 👍🏻Can you tell me where I can get the fuel pressure test kit That you are using please or a part number ?

@Kyles Transport Services Limited hey thanks for watching the video!. 👌 I've actually got all the fittings and pipework here. Just need to assemble the kit and put it on the website. I can drop a link here for you when it's live for people

@@TRUCKTECHUK That would be fantastic , keep up the great work

Yes, it's not a good idea and was changed on NGD. But if you crack the filter....it drains all the unfiltered particles into the fuel gallery 😰