Man, that's a beautiful build, even the way you've set up the electronics, with everything clean and tidy. That's what I call a perfectionist's build.

Great job, very professional wire routing with the din rail connector points. I had extected to see some din rail breakers for the stepper drivers but maybe they've got them built in.

it needs another piece of 2040 in the middle under the bed to tie it all together and to stop any push down above, on my version of this I have a piece of 8mm tapped aluminium for this bed and that is screwed down into the extrusion in on all 4 sides, its as rigid as it can gets now, finally it needs a brace across the two X axis 2040 extrusions , doing that makes X and Z very rigid. I used a piece of stainless steel that I had for this at 3mm thick. It makes a big difference now. Once final thing is I have the entire machine bolted down on a large desk which is heavy and has a thick counter on it made of a piece of granite. I then built a full enclosure which goes over it and keeps the noise down by about 30% and because I use a 1.5 kw VFD water spindle it is loud but very fast and accurate , mine also has ball screws rather than lead screws. its worth the extra cost which is not that much to be honest and helps to reduce backlash by quite a bit. My extrusion is bolted together rather than using corners which are fairly useless, simply drill through, counter bore and tap the end of the other piece with M5 allen heads. If you look closely in the video this was put together for speed of the video and most bolts and screws are missing. There are also some steps missing, you do not need to use the controller tin this video, any small grbl controller will work but you might need driver amplifiers.

Beautifull machine!👏🏻👏🏻

Wow very innovative ❤

You are genius ❤❤ future of Indian technology ❤

Nice video...Sir please make a video on higher/improved performance CNC machine something like laser cutting.. I mean all the mechanical parts should be easily available in market and there shouldn't be no 3D parts ( not everyone can make 3d parts, so implementations by viewers will be tough without all parts).

Good project💞💞

you are maestro for electronics

Bellissima idea , un po meno i pezzi stampati in 3D, complimenti per il progetto..👍

How well will this cut aluminium and brass ?? I'm interested in making this as the old Mach 3 3018 I have is not really up to it, it does do it but very slowly and it suffers from chatter and backlash, this has much stronger supports, linear rails etc so I would expect it to fair a lot better I need to mill brass and copper in small runs. thanks

Progetto ben fatto sei un artista.

Nice work. Thank you.

Well done 🙌🏻

Great wiring.

What was the Raspberry pi for in the box it was not attached to anything??

I suspose at some point you went back and aligned/squared everything? Not sure how or maybe I just missed it but you have no alignment or dowels to even remotley have accuracy. But If thats not what your going for. I guess it works.

hi is there a tutorial on how to do the electronic parts like sitting the whole thing ? i will buy a course if you have

Amazing machine

Really nice design well done - may I make a suggestion for even better rigidity? The rigidity in the X travel could be greatly improved by putting a web between the upper and lower black extrusions atm the gantry can flex creating a parallelogram shape

What is that pcb after 3rd motor driver and its use?Circuit diagram to make wiring? I have gone through the website but not getting properly

Great Content - what is the thickness of the steel laser cut parts?

Hi, I wana buid or can say upgrade my sewing machine using grbl motion control system and plan to do embroidery using inkstich post processor. Is it possible to do this. Can you give inputs on this project.

Excellent project 👍

Great work. That's what I want. A Z- axis built like this. Going to do it soon.

That's a great build. What extrusion are you using for the base, 2080 and 2060?

Well done? Excellent job? 1. How much it will cost from learning point of view? 2. Do all the mechanical part are available or some part will have be manufactured on order ? 3. Any offline training?

Dear sir, you have kept a rasperriy pi in the system. what is the purpose

Nice job!

Hi kindly let me know How to scale the machine size to 5*10 feet

Já trabalhei em montadora de placas eletrônicas tem umas colas especiais para colar o smd na placa e ajuda muito nessas horas de soldar os mesmos

Hey, Amazing! Can it cut through wood? and can it also accurately cut through foam used for furniture?

No you just need a suction system attached to the head to keep the debris clear of the tool.

Can we interface NEMA34 to that sheild

Huh ? Do we really need that big control box ? , itsnt it just enough to have a microcontroller and supply for it cnc shield and motor drivers for motors ?

Which are product number of linear rail and hoe many it cost to you

thanks

Its nice!

1:22 ah .. but where did you get those crucial parts? And what material are they made of? Looks like "someone" made those steel brackets beforehand?

What program do You use for make gears. Great proyect

hoi , i like your video. i want to make one for my own. but i have a question. can i use a laser too.? and if that is possibly how can i install it? greetings from Holland.

how mush linear rail and blocks cost you

Genial

Entek piro kiro2 iku om ?

I missed it - where did you source the spindle? Thanks!

I built this the board and a cnc but for some reason the UGS doesn't recognize the board and says I need to configure it manually? Did you have this issue?

I have window fabrication unit Its very useful for me Pls tell me how much it is..

THANK YOU FOR A GREAT VIDEO and some good ideas. I got a 3018 6 moths ago and I would recommended anyone to get one to start with as it is a cheap way to get into CNC routing. I found that I really like it but I now would like a bigger machine (only with a work area of 500mm X 500mm) so I am designing my own. As the ones you can buy cost too much. Like the idea of using threaded bar all the way thought the aluminium extrusion. Like the idea of two motors for the "Y" axis. I was thinking of using 20mm rail NOT 15? I will have to look at the different now? going to use HSK only because there is a supplier about 8 km from me. using a belt on the Z Axis is a great idea as it save on the Hight of the machine. why did you use Mild Steel and not Aluminium? steel is stronger but Aluminium is light and I thought it would be OK for something this size? Thought you might of used Ball Screws instead of Acme Threaded Rod?

I noticed that you had a Raspberry Pi how about creating a 3d printer with klipper (possibly delta)

Could you share dimensiones for all the parts that you use

what is the material used for the laser cut plates

Is that leadscrew? why not using ballscrew instead?

Excellent What's Total Cost? Thanks

quá tuyêt vơi👍

Congratulations, it is a spectacular project. Could it cut metal pieces? At least light metal like aluminum? What other types of materials could it cut?. Regards.

Don't you have any issues using tb600?

Please make a video how to add Limit switches in cnc switch and how to calibration .

Good project. I love ❤. Which program use on PC?

What is the appropriate cost of this complete cnc machine?

I would think that this style of linear rails rather than the round rod style would be more likely to be affected by the dirt and dust created by the cnc requiring more frequent maintenance. Great project though.

Bro make a video of writing machine

អរគុណសំរាប់វីដេអូរ

We have very cheap and high-quality linear guides, ball screws, linear modules, linear optical shafts, linear bearings, needle roller bearings, and rod end joint bearings. Do you need them, made in China😀

Spindle specification please 🥺

I want to buy this machine please reply

Hello. What is the name of the black chain for wires? Link to Aliexpress

link this link for software in description dude. project is good, but not without pc app for sending data to cnc ;)

Can this be made bigger

but keep uploading 😂

Plese make one more video and all things name yuo can used

How much

please sir send the code 3d grbl cnc

6:04 no no nooo..🤦‍♂

Great! But why not Arduino Uno + CNC Shield?

Total cost?

Arduino nano is not good for cnc because of flash memory. Need Uno or Due or any else.

rrect

be great if you had speech.

I am buying this masin from you

0+0 anyway. But you polute to

This is non sense making us pay to get important files like STL

This NOT DIY !! You bought a kit 1 THat's ok but don't call it DIY !

irrelevant

'DIY CNC' - step 1, buy a commercial CNC kit...

Mere ko bhi bna ke doge esi machine

Nice job. Why do you use two power source ? And what is the need to add a raspberry pi in this project ? Thanks

Hello anna me Phone number naaku alantidhi kavali antha price Aina paruvaledhu

Efektownie ale z mechanicznymi błędami . Brak kasowania luzów na śrubach pociągowych , brak łożysk oporowych na śrubach pociągowych , zbyt cienkie prowadnice , brak stabilnej podstawy to błędy . Nawet przy najstabilniejszej konstrukcji brak wymienionych elementów czyni całą obrabiarkę tandetną . Reszta to składanie kloców lego . Zdecydowana większość filmików o obrabiarkach CNC zawierają te same błędy konstrukcyjne nie naśladujcie bo szkoda czasu . Niewielkim kosztem można te błędy wyeliminować zastanawiając się w którym miejscu powstają ugięcia i luzy mechaniczne , właściwie 100% takich pomysłów to lipa - widać robią to ludzie nie mający pojęcia o mechanice albo robią to celowo by ludzi zniechęcić do budowy swojej konstrukcji windując koszty ,kreując firmy produkujące badziewie za grubą kasę . O głowicach wspominać nie trzeba zamiast kupić porządną frezarkę z regulacją prędkości na dobrych łożyskach sprzedaje się reklamowaną tandetę - frezarka dobra do takich celów kosztuje 3/ 4 stówki