DIY MrCool 2/3 Ton Heat Pump Install - Don't make these boneheaded mistakes!

  Переглядів 3,900

Franklin Hu

Franklin Hu

11 місяців тому

This video covers the installation of the Mr Cool heat pump to an existing electric furnace.
iwae.com/shop/2-to-3-ton-18-s...
iwae.com/shop/3-8-x-3-4-mrcoo...
iwae.com/shop/2-to-3-ton-mrco...
iwae.com/shop/24-x-36-x-2-e-l...

КОМЕНТАРІ: 20
@markbowker5936
@markbowker5936 9 місяців тому
SMART MOVE ON THE SURGE PROTECTOR 👍
@manalosmeanbusiness
@manalosmeanbusiness 2 місяці тому
What size crows foot did you use?
@leonmcooper8640
@leonmcooper8640 10 місяців тому
I am in the process of installing one of these. This video has been very helpful. How has your unit been performing?
@franklinyoutubehu2349
@franklinyoutubehu2349 10 місяців тому
It’s been great! No leak, low energy consumption and having central air is amazing. No more rattling window units.
@franklinthu
@franklinthu 6 місяців тому
I did have my first major failure. One of the 20 amp slow blow fuses tripped which resulted in just the fan blowing air instead of heating. I have seen the amperage rise to the 20 amp level, but typically 16 amps are drawn. so maybe it needs a bigger fuse in 2 ton mode. This happened after I returned home from work and was trying to raise the temperature 10 degrees which operated the unit for hours to get there. It can only heat about 4 degrees every hour. So, it isn't very quick for heating your house if you turn it down during the day.
@marianaqishbandi285
@marianaqishbandi285 5 місяців тому
I was looking at the 3 ton and it needs a 50 Amp breaker +27 Amp for heat kit + 15 Amp Air Handler. With a 100 Amp panels seems impossible with the extreme heat. Was that the case with you.
@franklinyoutubehu2349
@franklinyoutubehu2349 5 місяців тому
I do have a 200 amp panel. I'm not sure how all those amps add up since certainly the amps from all the breakers is more than 200. I suppose they count on you not using them all at the same time?
@mtbphil168
@mtbphil168 6 місяців тому
I just installed a 3 ton universal. I noticed it pulls 0.7 amps even when off!! This amounts to $180 a year in wasted energy. Do you know what your current draw is to the outdoor unit when off? Thanks
@franklinthu
@franklinthu 6 місяців тому
I have an ammeter attached to my circuit and it says idle draw is only .7 - 1.2 watts, not .7 amps. Are you sure you measured correctly with the correct units?
@mtbphil168
@mtbphil168 6 місяців тому
Yes, it was amps. I measured it with a handheld and I also have a split core current sensor that I monitor continuously with the Emporia energy system. One other owner said they measured 0.6 amps. I wish I was getting your reading!
@franklinyoutubehu2349
@franklinyoutubehu2349 5 місяців тому
My mistake, I was measuring when I had a blown fuse. The actual idle draw is .6 amps or about 13 watts.
@franklinyoutubehu2349
@franklinyoutubehu2349 5 місяців тому
Using a calculator I found online, at 13w running 24 hrs 365 days = 113.88 kwh and at an average electricity rate of .13/kwh, the cost is only $14.80 and not $180 for the year.
@mtbphil168
@mtbphil168 5 місяців тому
Thanks for checking again. Power = Volts * Amps so 0.6 amps at 240 volts is 144 watts.
@karmendimas5274
@karmendimas5274 4 місяці тому
your condenser should still be running when below 32F, why do you have it set that way??? thats not right,, unless i missunderstood you stating something..?
@franklinthu
@franklinthu 4 місяці тому
The 32 degree setting is mostly due to inspection requirements. I really should set it to 10 degrees
@karmendimas5274
@karmendimas5274 4 місяці тому
you should have it set for 0F,,, since this system is 100% efficient down to -5 F , i had the same system installed, and working excellent, was 28F a few days ago, and i checked the temp of the air coming out of the register and read 142F very impressed, i also do not have a heat strip installed, there is no need for it.. hope yours is working out well..@@franklinthu
@joeshearer1247
@joeshearer1247 8 місяців тому
Better hope you don’t have to remove the blower motor
Installing a VERY Efficient Ducted Heat Pump (MRCOOL Universal Install)
22:06
Mason Dixon Acres
Переглядів 63 тис.
Mr Cool DIY 2-Year REVIEW: I wish I would have known this BEFORE BUYING...
19:58
Mr.Cool 2-3 Ton Install, On Existing Furnace
13:09
Bobdudeman1988
Переглядів 968
This is Why Heat Pumps May NOT Be The Future
13:12
Skill Builder
Переглядів 2,3 млн
MrCool is in the house!
17:44
Engineer775
Переглядів 30 тис.
How to install water pump without pressure tank | DIY
11:58
JMS VLogLife
Переглядів 2,5 млн
MRCOOL HVAC Good and BAD!
16:44
HVAC Guide for Homeowners
Переглядів 56 тис.
Installing a MrCool Universal with a Gas Furnace
4:33
MRCOOL
Переглядів 38 тис.
DIY Mini Split Install - All the Things Nobody Shows You
33:25
LRN2DIY
Переглядів 1,7 млн
ГАЗ-53 на максималках #авто #газ #пикап #грузовик #кастом
1:01
#ЧУДОТЕХНИКИ с Георгием Беловым
Переглядів 1,8 млн
John Deere 6430 #tractor #ploughing #lemken 😎 @FlyingPixelsPhotography
0:15
Van Dronewerk Agro
Переглядів 2,9 млн