Few people know about this function DRILLS !!! INVENTOR: / @user-jl9ip4wk5t
КОМЕНТАРІ: 2 800
@user-jl9ip4wk5t3 роки тому
*Как вам функция дрели? Не ожидали?*
@DIMKA_BY3 роки тому
А какой чистый рез... Просто мечта))))) зачем придумали фрезер с чистотой оборотов до 30.000тысяч.
@helgenigma3 роки тому
все это спизжено и перепизжено уже тысячу раз. скучно.
@user-kv8jv2lw4e3 роки тому
Зачем придумывать велосипед, если он давно придуман.
@Aleksandr-_3 роки тому
@@darkwolfc если тебе для работы, то он окупится если купишь нормальный и будет прибыль приносить, а если на раз то и незачем фрезы покупать что бы из дрели черти что делать, проще к столяру обратиться.
@Aleksandr-_3 роки тому
@@darkwolfc ну нет у дрели таких оборотов.
@Tool-Meister2 роки тому
Very clever project. However, drills and routers have different kinds of bearings. Routers always have bearings designed for lateral thrust. Plunge routers also are designed to resist linear/axial thrust, the same way drill motors are designed. Most drill motors do not have bearings which are designed for lateral thrust. If you build a router using a drill motor please be careful of the load placed laterally on the shaft. Otherwise you will quickly wear out the drill motor bearings. Unfortunately, crafts people learn this lesson on drill presses which are used for drum sanding. The constant lateral pressure can ruin the drill press’s runout if the bearings are not designed for lateral thrust. Good quality woodworking drill presses have bearings designed for both lateral and linear pressure. Many metalworking drill presses, especially inexpensive ones, do not have the lateral thrust bearings and are subsequently damaged by lateral thrust applications. I’m in my seventies and have witnessed this firsthand.
@xfhghe2 роки тому
Drill chucks are only designed for axial loads. They are not meant for side loads and can easily fail when such a load is applied. Routers and end mills need to be secured in a collet to be used safely.
@Tool-Meister2 роки тому
@@xfhghe : Great comment! The drill chuck incompatibility with side loading will likely cause a failure long before the drill’s bearings. Please notice the rarity of a drill chuck being used on a milling machine for any purpose other than drilling, reaming, or tapping.
@vadimshink92572 роки тому
Всё верно, надо искать способы как на высокооборотистую УШМ прицепить данную фрезу.
@happygilmore21002 роки тому
Very well explained.
@yeldog112 роки тому
The saying, "The right tool for the job" is not just for completing the job but it's also for safety. You are absolutely correct.
@mathiase.70963 роки тому
Don' do that. The Clamp-screws, driven in the end grain are not at all stabile. The speed is not about a quarter as recommended for router bits. The bit is not fixed strong enough in such a machine. There are some more points... THIS IS DANGEROUS! Kick-back, losing bits at full speed . . .
@user-sl9sn9op4v2 роки тому
Весь мир против этого)))
@herbyverstink2 роки тому
also.. its not like routers are so expensive that it's worth taking risks.. this seems more like a proof of concept
@danialhowe98142 роки тому
100% correct and it all starts by not being parallell to the works space
@jesusislord65452 роки тому
Repent to Jesus Christ! “The light shines in the darkness, and the darkness has not overcome it.” John 1:5 NIV
@lordshadeus2 роки тому
Прально глаголтит хоть и по иностранному!
@br4d1012 роки тому
So glad I watched this, almost stupidly went out and bought the correct tool for the job! A router!
@varpos2 роки тому
Haha, great comment! This is for people that prefer danger over spending some more pennies to keep your health...
@Slice-Darryl2 роки тому
those are the kind of videos that show you the value of the dislike count rip
@fredlenz47432 роки тому
Extremely dangerous. Router cutter in terrible shape, rusty. Screws holding the drill in jig. Recipe for disaster
@harryhalfmoon2 роки тому
@@Slice-Darryl Exactly my first thought when saw what this video. Went down to the comments for verification. Was not disappointed.
@user-tc7lb6rr4r2 роки тому
Exactly!
@VANO7267Рік тому
Дрель не рассчитана на радиальную нагрузку, только на осевую. При работой фрезой идёт радиальная нагрузка на передний подшипник, и как итог, в последствии, можно будет её , дрель, выкинуть, так как патрон будет болтаться.
@John.S.silver3 роки тому
Коловоротом ещё можно попробовать пофрезеровать. А если на УШМ поставить зубчатый диск, дрова можно пилить втрое быстрее. А если колесо от тачки, то кататься. Это Вам идеи для будущих роликов.
@user-ro3eu6cn6v2 роки тому
Какая хрень! Дизлайк.
@rafkatmakalim7072 роки тому
На УШМ КАТЕГОРИЧЕСКИ ЗАПРЕЩАЕТСЯ ставить зубчатый диск и тем более пилить дерево используя УШМ. Сейчас тут не осведомленные прочитают твое сообщение и попрут в госпитали с перерезаными шеями. Зубчатый диск предназначен для циркулярных настольных машин использующикся в мебельно дерево обрабатывающей промышленности.
@dalnegorskrecords13542 роки тому
Буквально с месяц назад, чуть ногу себе не отпилил "зубчатым диском"! Думал всё предусмотрел! ...только ушм шутить не любит!
@user-fl3tt1bu2w2 роки тому
Да ладно тебе, зато исполнение аккуратное, можно гордиться как красиво по лбу прилетело!
@dalnegorskrecords13542 роки тому
@@user-df5ws3re7p Василий! Как и везде, всё надеемся на авось, и русский, небось! Только у меня УШМ 1980-х годов выпуска! У неё нет кнопки, которая при отпускании, не срабатывает на отключение. Конструктивно так выполнено! ukposts.info/have/v-deo/m3aWk5ilm6Km1nk.html ...а в прочем, это не большая проблема, если действительно соблюдать правила Т.Б.!!!
@Tugella7773 роки тому
Люди не повторяйте . У дрели оборотов 3000 тысячи у фрезера 30000 . Я тоже посмотрел видео решил попробовать и чуть без пальцев не остался . Хорошо соблюдал технику безопасности и были догадки что работать не будет .
@user-zv6vt6zx9i2 роки тому
Я тоже об этом подумал что это всё шняга
@user-pj6mu4rv8b2 роки тому
А чего дизлайк не ставим?
@user-yq1fi6ys8m2 роки тому
@@user-pj6mu4rv8b Потому что по новым правилам дизлайки видно только хозяину канала
@No_Name070502 роки тому
Это первое, о чем подумал, увидев ролик. С таким же успехом можно использовать перфоратор в качестве нейлера.)))
@user-uy9un8pp3f2 роки тому
Согласен с вами полностью но есть одно "но". Когда для "домашних" условий ради пару досок надо например для скамейки на дачу, то почему бы и нет!?
@dariolima15992 роки тому
Muito bom trabalho meu amigo excelente trabalho que DEUS te abençoe e te guarde muito obrigado por essa excelente ferramenta que DEUS te abençoe e te guarde
@prolijo66722 роки тому
maravilloso trabajo mi viejo,esa base para tornear madera esta de lujo
@sergeizaikin50983 роки тому
Не вдаваясь в в другие аспекты этой конструкции, сразу можно сказать, пару раз открутиш, закрутиш боковые саморезы и они перестанут держаться, это не есть крепёж для регулировки (в дерево). Да и все остальное не выдерживает критики, все уже написали в комментариях. Когда заняться нечем делают такие одноразовые поделки
@user-ob4ms7wz2y3 роки тому
.. он подал идею, а из чего изготавливать ваша проблема
@nberger73183 роки тому
Херня полная!
@toligusan39223 роки тому
@@user-ob4ms7wz2y правилно
@user-fl5og5rd4w2 роки тому
А если мне нужно сделать 5м/пог.планки?мне что покупать фрезер за немалые деньги?так что для небольших объемов как раз. Молодец,спасибо за идею!
@Degauss132 роки тому
@@user-fl5og5rd4w все верно, лучше за еще одной дрелью сходить
@neliorodrigues2249Рік тому
Muito bacana ficou excelente seu projeto é uma ótima apresentação e muito boa à ferramenta de grande utilidade obrigado VALEU
@user-lv4wj8cb2d2 роки тому
Срок службы такой приспособы думаю меньше, чем время потраченное на ее изготовление. Особенно саморезики, вкрученные на 5 мм, долго не протянут. Тем не менее 9 лямов просмотров набрано! А это в видосе самое главное!
@volchitsa059Рік тому
Такая приспособа на Алике продается за 1500₽
@user-wz3im1lp9fРік тому
13 (тринадцать) миллионов 😱
@user-hx1iy6wo8g6 місяців тому
обороты не те
@jeffersonoliver42446 місяців тому
13
@zbigniewczaykowski5142 роки тому
As a professional woodworker of 37 years, don't do this unless you want a trip to hospital
@user-ti6vv6he9y3 роки тому
С нашим Атоманом не приходиться скучать😉🙂
@kenwood7773 роки тому
хотя бы поугораем от души
@user-ex8tf1nm8m3 роки тому
Жалко дрель. Лучше уж фрезером сделать работу. Я не стану микроскопом гвозди забивать
@friedrichkrutsch49732 роки тому
Как вариант выйти из положения, почему нет? Вот только оборотов у дрели на порядок меньше, будет ли такой чистый рез, как и у фрезера? Что касается " микроскопом гвозди забивать " в данном случае неудачно, здесь больше подойдет ТОПОРОМ. Мискроскопом скорей будет фрезер, но не дрель.
@user-jg9py8qd3d2 роки тому
Класс! Теперь осталось снять видео, как сверлить фрезером и забивать гвозди шуруповертом!
@Batorg12 роки тому
Делал я такую приспособу, могу из опыта сказать, что лучше не мучиться а купить фрезер. Скорость вращения дрели малая для этих задач, по этой причине появляются две проблемы. Очень медленная скорость обработки и такие материалы как ПВХ и оргстекло он рвёт, по той же причине, малая скорость вращения.
@andreyalla225 місяців тому
Здравствуйте. Не подскажете из своего опыта. Для утепления фундамента есть ЭППС - 50 мм. Нужно, чтобы во время заливки бетон затёк в бороздки и крепко связался с плитами Пеноплэкс. Покупать для нарезки бороздок фрезер не хочу. Есть советская дрель , думаю купить фрезу Ласточкин хвост и сделать такую опору на один раз. Два вопроса - какого диаметра внизу взять фрезу и не убьёт ли эта задумка дрель? По идее плотность ЭППС меньше, чем древесины, но как быть с боковой нагрузкой на дрель, просчитать не выходит.Что думаете? Спасибо.
@wellingtoncostasoares19963 роки тому
Meu caro, essa sua tupia caseira ficou estupenda. Meus parabéns!
@pauloproatti68323 роки тому
realmente valeu ovideo
@willb36983 роки тому
Well, my Russian Brother,.......it's Brilliant. Thanks from Australia.
@eliasleaomarceneiroРік тому
Boa ideia, mas esta máquina não foi feita para receber força lateral, logo estará com enorme folga no rolamento.
@Serega_SiniyРік тому
Красавчик,золотые руки! Подписка,лайкос из Беларуси!!!👍👍👍
@user-sh3rl3rs6u3 роки тому
Ну что, автор... поздравляю! Ты изобрел деревянный фрезер! в 21-м веке! Молодец! Доктор Дью по тебе плачет :)
@user-boloto2 роки тому
А по факту, у автора есть просмотры и комментарии.
@IgorSchitov2 роки тому
@@highway4275 9 миллионов просмотров нет смысла?
@Roman_Pivnov2 роки тому
@@highway4275 а так можно?😳
@user-bn9db4cj5w2 роки тому
как говорит наш доктор 250 из 250 очередное полное яухин ))))
@santus2211Рік тому
@@user-bn9db4cj5w 250 полуляхов, братан) но тут уже в гигаляхах нужно измерять)
@user-md5rx2sh6e3 роки тому
Это что-то невероятное.Как я раньше жил? Пойду фрезер выкину.
@user-hf3oj2wn3t3 роки тому
Зря, из фрезера получится утюг, Вы только отдайте его изобретутелю.
@user-nl3zz2lb1m3 роки тому
Фрезером можно сверлить .
@nikgrey73343 роки тому
@@user-nl3zz2lb1m можно и резать вместо пилы и не только
@user-xz1cg5dg4u2 роки тому
а я саоим фрезером коктейли взбиваю
@obe1kanobe220Рік тому
Автор ты в курсе какие обороты у дрели и у фрезера? К тому же дрель не рассчитана на перпендикулярные нагрузки. Это насколько надо быть бичем, чтобы не позволить себе любимому заводской фрезер, он стоит не больно много
@user-mm6ni5iy8r5 місяців тому
Да это издевательство над дрелью
@Marklloret950Рік тому
Thank you for sharing this video. - years ago I purchased a router, but it was too complicated. This home made tool is perfect.
@thegoodfight3653 роки тому
Simply awesome ingenuity bro. Maybe I'm just too easily impressed. But I don't think so. That's an awesome job. Thanks for sharing your work.
@PavelSmolev3 роки тому
Почему я не сделал этого раньше?😂 это нужно уже в МегаЛяхах мерить))
@angelb46772 роки тому
The bearings in the drill are not designed to take lateral loads. You will eventually end up with excessive run out on the spindle.
@mikevolante7663Рік тому
Bearings, chucks and safety aside, its still a very clever piece of engineering. Ive never routed with a drill, but we've all used them laterally at some point to widen out a hole or something
@douglasflores1462Рік тому
It is fine, but drills don't have the speed required to use router bits.
@kylefisher4883Рік тому
Yea tried it once and almost lost a thumb...10 outta 10 wouldn't recommend
@user-bg4kv5xs9h3 роки тому
Есть дрель, а есть -фрезер. Это разного назначения устройства. Как болгарка и полировальник.
@santiagoraposo71623 роки тому
Muy curioso
@albertoortega41903 роки тому
Excelente .muy buena la idea
@user-xy4iq3kx8f3 роки тому
Не полировальник, а умывальник.
@user-bg4kv5xs9h3 роки тому
ВЕК полировальная машинка. Сокращение-полировальник( в простонародье).💁♂️
@user-xl2sg1qo7r3 роки тому
Старина,видимо люди об этом еще не знают! До них надо это донести и обьяснить! Я с тобой согласен на 300 проуцентов.
@eduardosurname20293 роки тому
Vale pela ideia em si, mas quem for fazer precisa ficar atento ao seguinte: 1 Usar pinus ou compensado para construir ferramentas é um contrassenso. A durabilidade é mínima. 2 A rosca do parafuso que ajusta a altura da broca, por ser pinus, vai espanar rapidamente. 3 A precisão do corte, fica totalmente na dependência da habilidade do marceneiro, pois não há uma guia.
@joabe2212Рік тому
Show
@sandrab.nelson4893Рік тому
Excellent, excellent!!! Thank you so much!!
@franciscopino727Рік тому
Buen trabajo, no se puede desconocer... Independiente de el resultado... Buen armado de la maquina..
@user-bg5vy1we2w3 роки тому
16-я позиция Камасутры по применению дрели.
@user-xl2sg1qo7r3 роки тому
Таких позиций еще наберется блин!согласен с тобой.
@annarose48323 роки тому
Coat both mating surfaces and let sit for maybe 5 minutes. Then apply another coat of glue especially on the end grain. Let stand a fee minutes to allow glue viscosity to increase. Then join. Doing so allows the glue to be absorbed into the wood grain creating a stronger joint
@harryhalfmoon2 роки тому
Next, coat your hands and arms in glue and apply liberal sheets of carbon fiber, for when, not if, this contraption decides to buckle and tear a hole in your wrist.
@levinonunes52549 місяців тому
Oi amigo muito boa esse trabalho, quero fazer um , poderia colocaar as medidas que vc usou? Obrigado
@user-js8eu5oj9zРік тому
Есть маленький нюанс, дрель не рассчитана на длительную и боковую нагрузку
@RionDark3 роки тому
Как говорил Доктор Дью: Хуже всего, это когда самодельщик п***дит идею у другого самодельщика!"))) Регулировка высоты вылета фрезы за счет двух саморезов и шайб - это отдельное исхуйство! Срочно зовите Доктора! @ДокторДью
@user-dz2ni5xs8h3 роки тому
Что вы курите.рейсмусом не всегда угадаешь а этой приблудой?....
@user-xr6wj6de7g3 роки тому
Господа но это же шляпа! Нас обманули!🤣🤣🤣. Зачем изобретать велосипед,тем более очень плохой велосипед.?😳
@srgpopow2 роки тому
Если дядя работает на дрельной фабрике, шлёт дрели всем ящиками, идея годная.
@scratchluka61572 роки тому
A drill for screws. And drilling small holes. A router is for removing larger portions of material ( mainly wood) at higher rpm’s and much sturdier. The right tool for the right job. You can use a screwdriver to drive a nail but it doesn’t mean you should. But you got an a for effort I guess
@svkscorpio3 роки тому
Router involves higher speeds and hence it will result in a fine cut. Drills do not provide that much of speed and hence the cutting/grooving will not be smooth enough.
@chriswhitley32832 роки тому
That’s true, but in situations where you might want better control of the situation the lower speed might come in handy. Also, if you do not have a router. This would help you greatly to have a conversion kit for your drill. I have a conversion kit for my dremil and use it quite frequently. Of course as you say, the dremil does have the higher speeds.
@GitXxxd2 роки тому
I agree. I think drills would perform better as lathes ??
@indtvsol51923 роки тому
Какая скорость вращения на дрели? И какой патрон должен быть? Удивляюсь как ещё в перфоратор не поставили
@vadimshink92572 роки тому
Только в УШМ пойдёт по нагрузкам и оборотам, но и соответственно нужны способы как закрепить и станину под неё сделать.
@indtvsol51922 роки тому
@@vadimshink9257 а не проще купить хотя бы дешёвый фиалент и остаться здоровым с целыми яйцами, чем мудрить непонятно что.
@vadimshink92572 роки тому
@@indtvsol5192 Можно. как раз сгоревший Фиолент валяется без надобности 2-ой год. Причем сгорел когда не дал фрезе раскрутиться, а в ДСП рано воткнул.
@0imax2 роки тому
@@indtvsol5192 а как же естественный отбор? Не, пусть это и жестоко, но эволюция должна отсеивать неприспособленных))
@heretoserve5023Рік тому
WING NUTS... Thanks for the video I think I am going to try it I was just going to say, have you thought about using wing nuts for the depth adjustment? (...just thinking it might be easier than using a screwdriver...) (but I think a hand-held router would work just as well?) ? Again thanks for the video- it looks like it works well!
@Ghosthawk332nd2 роки тому
Congratulations, you turned a drill into a router. Not as much speed, or horsepower. Nice work on building the wood piece.
@user-xc7yk6vz6i3 роки тому
Одноразовое применение, за неимением лапши и чай жакшы! 😁
@UUTechRU3 роки тому
230 Полуляхов из 250 =) Матвееву - Привет!
@metalllist13372 роки тому
почему 230 то а не 250? А от вида ржавой насмерть фрезы ПХМ дымиться должен начать
@temanyi4e242 роки тому
Тут не Матвеев а доктор дью должен посмотреть
@slightyawesome4859Рік тому
идея огонь, осталось найти дрель хотя бы тысяч на 20 оборотов...
@nuwache2 роки тому
Великолепно: просверлил открутил, фрезернул прикрутил. И так весь день крути - верти. Суходрочка.
@sergeythomasoff90293 роки тому
Фрезер одноразовый...
@vivendoaprendendo-xandao46703 роки тому
Muito bom preciso de uma e estou sem dinheiro, agora está resolvido vou usar minha furadeira.....parabéns Deus abençoe
@Valery_1954Рік тому
Если руки и пальцы лишние - флаг в руки и барабан на шею ))
@JonyRottenРік тому
Well at least you guys keep the ER busy😂
@Dimitry.9112 роки тому
Дрель не предназначена для боковых нагрузок. Если только не жалко ее. Оборотов мало. В общем, если сделать минимальную разовую работу, может и пойдет.
@user-ns8ex8jy4m3 роки тому
Купи дешманский " Фиолент" и не страдай ху*нёй ! Кстати фрезы замачивай в солярке , от смолы очистиш и подшипник подольше побегает ! Но лайк за старание ставлю ! Удачи !
@user-yf4fv8op7c3 роки тому
Нашёл дешёвку.Фиолент дороговато будит.
@user-bg5vy1we2w3 роки тому
@@user-yf4fv8op7c Фиолент 3500.Эта сумма 2 раза нормально в магазин сходить за продуктами.
@tworesponses41303 роки тому
Вместо дрели ещё можно использовать кофемолку. А если прикрутить фен с вырванной спиралью синей изолентой, ещё и удаление опилок получится. Туда же приматываем телефон для подсветки и видеофиксации работы. Аффтар, жги исчо!
@c.rutherford2 роки тому
Clever but the side adjustment screws will stop working eventually the wood will become mush with repeated screwing/unscrewing
@PenolibeРік тому
No hay taladro de BRICOLAGE que tenga la velocida adecuada para fresar correctamente.
@brucedunning10053 роки тому
Just buy a router and use your drill for drilling lol
@RobertSeviour13 роки тому
Alternatively, use your router as a drill.
@gusdogbrownlab4353 роки тому
@@RobertSeviour1 or use your router to connect to the internet so you can see how to turn your drill into a router!
@RobertSeviour13 роки тому
@@gusdogbrownlab435 Or make a video on how use your router to connect to the internet and use the YT payments to buy a drill.
@robertoarriola-bustamante91693 роки тому
Not everyone can buy a router
@shaunmcdougle3 роки тому
And yet, He achieved the result he needed. These videos are about resourcefulness, ingenuity, and sharing ideas (things that build nations by the way), not about reaching the best result or even about achieving the same result as a purpose made tool.
@user-km3rt8jr2f3 роки тому
За исполнение пять, за идею КОЛ! Сравниваем количество оборотов дрели и фрезера и сразу становится ясно за что КОЛ.
@user-dh9td7tr1w3 роки тому
Фрезер и сам по себе мощьней
@__-uk8cf2 роки тому
Я думаю - наоборот, идея то хорошая, но исполнено топорно, опасный станок получился, берегите руки, как говорится
@Vikenty-A2 роки тому
Фёдор-молодец! Как фрезеровщик-фрезеровщику!
@palarts12392 роки тому
Очень маленькая подача нужна
@nimbus8902 роки тому
Подшибники дрели не рассчитаны на боковые нагрузки
@joee7626Рік тому
Holy shit! You made a nine minute video showing how you put a router bit on a drill motor!? How incredibly revolutionary, this is going to change the future of mankind!! So amazing!
@muthuraj.pandiyanmuthurajp7129Рік тому
Thanks very much sir .God bless you always happy.
@Riuslan743 роки тому
А что, есть и свои плюсы, пока существуют ДиАйВайщики, у доктора ДЬЮ всегда будут пациенты и работа. В общем так держать!
@tollmuch3134Рік тому
Тут, однозначно 250 Полуляхов из 250. А может уже и на шкалу в Мехаляхах пора переходить.
@user-ux2le1gq5r3 роки тому
Как временная мера на крайний случай - имеет право на жизнь, потому как из подручных материалов, бесплатно, и дрель у всех есть👍. А так конечно как в той поговорке получается: за неимением горничной @бут дворника🙃
@user-pj6mu4rv8b2 роки тому
Фрезы стоят в полфрезера. Попробуйте ещё на болгарка замастырить через быстро съёмный патрон от Шурика. Вот пальцы разлетаются по мастерской. Велосипед.
@cuasimodus111 місяців тому
Es fácil hacerlo, lo malo es que los taladros no pasan de 3000 revoluciones y para rutear se necesita por lo menos 10,000 revoluciones. buen video!
@snakeyengel3 роки тому
what is the music? great synth work on it!
@toretotrujillo94663 роки тому
Excelente y muy util... Solo que podrias decir medidas de las piezas de madera por favor...
@artemb39772 роки тому
Это просто хардкор! Такого не ожидал... особенно впечатлила фреза из помойки
@dangelo43792 роки тому
Que ideia genial! Sugestão: ensina a fazer um macaco hidráulico com parafusadeira, cantoneiras e parafuso. Vai ser bem legal
@brucebr10373 роки тому
Google says "Drills lack the power and speed for effective and safe routing. Routers and drills both work by rotating a bit secured in a chuck, or collet, but that's where most of their similarities end. ... This mechanical difference, among others, makes a drill unsuitable for use with a router bit."
@BeasleyStreet2 роки тому
I'm with you on this....just because you can doesn't make it ok.....
@Djuuker2 роки тому
Those poor bearings .... Drill bearings are not designed for sideways pressure, and will wear out/break very fast when used in this manner...
@amandamartin97702 роки тому
I was thinking this would be a great option if you have a small job to do and cannot justify the cost of buying a new tool that you won't likely need to use again. Not as a permanent replacement that would get lots of use.
@buster80152 роки тому
What a truly hideous idea to adapt a drill for a router, why?? Not enough rpm, timber and screws as an adjustment clamp 😳😳totally dangerous in every respect!! . I'm a carpenter of 25 years and it goes to prove the safety standards and thought process difference between the UK and certain European countries.
@buster80152 роки тому
@@amandamartin9770 and spend a day making it?? Get a grip, a router can be purchased from screwfix cheap enough
@garywinterbottom60733 роки тому
I worked with industrial woodworking routers wadkin bursgreen machinery the speed needs to be at least 15 to 20 thousand rpm at the bit to be safe and accurate.
@januszR3 роки тому
Also for long time use drills are not made for pressure coming from the sides... still clever idea.
@deusdetemoraesrocha9092 роки тому
Muito bom, parabéns!...
@dand3975Рік тому
Using that holder as a portable drill press could come in very handy.
@user-vorazan283 роки тому
Почему отверстие в центре неровно просверлили😀😀😀
@ODX1713 роки тому
A $100 Laminate router works even better and less hassle running at 20-30 K RPM for a cleaner cut.
@antonpetrusin16672 роки тому
боковые зажимы заморезами на пару раз, время+матерьял, легче купить не дорогой фрезер
@PavelWoodРік тому
12 тысяч столяров скорей всего оценили по достоинству это "гениальное" изобретение 🤣🤣🤣
@user-ox5wj7hd4c3 роки тому
Еще никто не знает как дрель с помощью скотча или изоленты может смотать удлинитель ))
@bobsradio60253 роки тому
That router bit has a beautiful coat of rust on it.
@iareid82552 роки тому
The issue of side loading the drill bearing has been mentioned. Wood screws into end grain do not give a strong connection as the screw severs the wood fibres meaning little strength. Ok for a one off job but really get the right tool for the job, even if you have to hire it.
@user-ti4jy5bp1e2 роки тому
Вот так из ничего можно сделать приспособу для разовой работы. Профессионалы посмеются,а кому-то может помочь. Надо только понимать,что дрель не рассчитана на такое направление нагрузки и долго не выдержит.
@Godisknockingx3 роки тому
Yes, it's easier to just buy a router. But it's cool to see that this idea actually works. Well done.
@elizondocr3 роки тому
But also pretty dangerous, its a fact that you can take any motor and adapt those cutting tools and do the same, you hit the nail, buy a router that is built to not destroy your fingers
@conway5732 роки тому
@@elizondocr Agree…
@buster80152 роки тому
Totally agree, a spinning motorised tool can be used and adapted for a range of purposes but why?? this is hideous and clearly not safe, anybody who thinks these wooden deathtraps adaptions are a good idea needs to seriously get a grip. I'm a carpenter of 25 years.
@josephwalsh34012 роки тому
@@buster8015 I wish I had seen this a year ago before I spent a lot of money (I could ill afford) on a router that I use periodically. I don't see how using this device is more dangerous than using the drill to drill holes in a wall! It's probably safer.
@buster80152 роки тому
@@josephwalsh3401I could not disagree more, hideous makeshift tools are not a substitute for approved and tested equipment. Not to mention the time and effort involved to produce these devices. To endorse such ideas is as idiotic as the concept itself
@user-bs5sz1wf6w2 роки тому
Показать суть этого "гениального" изобретения можно секунд за 15-20)))
@therickpound2 роки тому
I always ah e time for good ideas, you could use a spring to make it more controlled, and make bottom from Perspex then u can see..cheers
@user-yi6lt7rd2qМісяць тому
Инженер Конструктор Изобретател-Браво
@user-lc1um8xu7d3 роки тому
Музыкальный ряд зачётный!!!
@222wotblitz73 роки тому
С одной стороны ну да молодец прикольно, с другой стороны после 5-7 раз использования эта дрель выскочит из деревянного хомута И натворит таких делов , пока вы ее поймаете . Вообщем за технику безопасности 2.
@user-bq1jd4vr7s2 роки тому
Мужики, для домашних разовых работ берите себе фиолент 1050 ватт примерно, с боковой ручкой (а-ля фестул) и будет вам счастье. Недорогой и выносливый, для мелких работ по дому самое оно. Мы такие в столярии годами мучали. А вариант с дрелью... ну для очень колхозных работ, типа углы на палке закруглить, которой будешь в ступе воду толочь.
@dennisford20002 роки тому
Unlike our wood , yours is much better. Nice fine growth rings .
@deldridg2 роки тому
Hmmm - novel idea, but I think I'll stick to my router table. Drills don't have the necessary RPM - somewhere above 20K as I recall. Mine's close to 30K RPM from memory. The neighbours love it when I fire up that sucker early on a Sunday morning. :-)
@Splatterpunk_OldNewYork2 роки тому
Mmmmmhhhhhmmm. I also love to remind my neighbors that I have bitchin' power tools.
@user-mn7nn5fc3m3 роки тому
Как угробить дрель.запоминате.
@user-ze8ux7pw7l3 роки тому
Бред. Обороты дрели и фрезера?????
@ovidal1Рік тому
Que buen invento, quería comprarme una fresadora y no tengo dinero, gracias desde Chile.
@gilbertoisaiasvilchezestra74462 роки тому
muy interesante, muchas gracias amigo.
@ChipEstrada3 роки тому
Look a Giligans Island Router. Sorry I've been a carpenter since 1975 and a drill doesn't have the RPM's to be a router. This is a dangerout idea.
@SodiumInteresting3 роки тому
agreed even if thise bigger drills have more rpm than some its not a router
@tsfarken3 роки тому
Plus the bearings aren't designed for sideways pressure.
@ChipEstrada3 роки тому
@@tsfarken But if you were stuck on a deserted island, I guess you could still make ornate furniture....... LOL
@johnfrench87143 роки тому
can't see those adjustor screws on the side biting many more times either.
@tomspring67203 роки тому
chip, thanks for a good laugh, i guess some countries they have to make with what they got, just like on Giligans Island! is that Russian writing?
@user-ow7cg5vu7j3 роки тому
У доктора Дью кровь из глаз хлынет, если он увидит. А он точно увидит.
@user-rr4yq3yy8l3 роки тому
Who is Dr.Dyoo?
@Brachkoff3 роки тому
@@user-rr4yq3yy8l It's Dr. DIY
@ksenia63012 роки тому
Респект за сооброзительность.
@thehatetank90572 роки тому
Wonder if this concept will work for a portable drill press also? Going to have to try this out.
@bodgerdavesumnerРік тому
It will until you put too much lateral pressure on the drill press bearings.
@user-hp4hb3lb3b3 роки тому
Гениально!Дилетанты рукоплещут))
@yzulina91313 роки тому
хороший метод убить фрезы.
@gilbert7360Рік тому
I've learned something about the drill matchine you have open up my mind stay blessed thanks