Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia

I think it’s a great built even if it’s not 100% it will work only thing I would add is interchangeable wheels for bigger sizes

Apesar de ser tão jovem, porém muito sábio e incrível a tua sabedoria além de ser super organizado. Está de parabéns você é um excelente profissional.

I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.

You've got every tools every piece wow 👍

Exelente maestro, no le doy un aplauso sino un millon, felicidades

Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.

Awesome! Im new to metal work... and would love a pipe bender... Gonna have to wait a whil longer before I can do anything like that!

Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!

I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste. I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan. People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues. This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.

Straight onto business. That's what I call a workshop

Great little project, nice finish. Great video, thanks. 😊

a very useful video, as long as people watch it, the more God's reward flows for you.

Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.

No pues... tienes un buen de herramienta. ¡ Tienes una ferreteria! Yo a luchas tengo unas pinzas ☹ . Pero exelente trabajo 😀. Me gustó lo que hiciste.

The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU

Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍 Pozdrav iz Srbije

Good videos tutorial next time boss 👍👍👍

The first construction of the new workshop, it is so much more rewarding to make your own tools 🛠

Genial, excelente tutorial

Keep up the good work 👍

Very nice work!

Boa tarde! Gostaria de ter muitas ferramentas assim... parabéns pra você!

beautiful, thank you for sharing

Excellent presentation. The Lord God bless you in Jesus mighty name

hello where did u get those bender dies/wheels please?

the tools are complete.. thank for sharing

Thank you so much for this bender making technical education

welding on a wooden table is a bad idea bro!!! great bender

Where can I get the pulleys?

Ottima costruzione, molto robusta, 👍👍

i follow Leandro Torneiro, an brazilian maker doing this project and must tell, this tool is awesome!

Where did you get the roller dies frome i cant find those any where! Help!!!

GOOD IDEA SO MUCH

Good idea! Thanks for sharing. Keep safe. Watching here in Canada

Good workshop..good work

Intelligent. Boss. Realy

Well done 👍🏻

Boa tarde amigo Pena que não é aqui no Brasil Gostei muito do seu trabalho se fosse aqui eu ia mandar fazer uma dessa pra mim Susesso no seu trabalho merece mil likes

Extremely good. Very beneficient. .

Step 1 - have all the key expensive components of a retail bender tool...

Nice job.....would like to have one ...with variable clutches...

Perfekt tool. Good job.👍

good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.

Well done, in my opinion, you just needed to make a 90-degree fold and another 180 to see how the curves will be.

Where did you get the wheels?

Good fabricator nice job.

Hey man great job but I see a problem it’s flexing needs more reinforced and needs to be mounted to concrete not a wooden workbench

Thanks 👍 Alhamdulillah

Dobra ideja,pravio sam sebi nesto slicno,ide to mnogo lakse uz grejanje

Excellent!!! 😁👍Although, you might have to heat it with a torch to make it easier.

Muy bien es un trabajo extraordunario

Very nice

What happen to measure twice cut once?

Nice bender... Good job sir.

Красава , просто быстро и эффективно !!👍👍👍👍

Nice work idol

Fantastic 👍🏾

Excelente labor

Idées et conceptions très utiles, mains en l'air, salutations du Maroc

LOOKS AND WORKS GREAT, THANKS FOR SHARING. CAN YOU MAKE A METAL ROLLER TO ROLL FLAT METAL PIECES? 🇺🇲🌞👍✌️

Smart and effective!

Отличная работа! Спасибо за видео!

🙏Sir Excellent your job keep your blessing us 🙏 i from mumbai india

👍👍👍👍💯

Where can someone by the round dye pieces at!!!???

Excelente...mis sinceras felicitaviones...desde Nicaragua.

you need thicker plate and a more solid handle. a few more bends and its going to bend or break

Greetings, you can add a little bit of oil to make it easier to slide

ALI JE LIDL PRAKSIDE PLAZMA DOBAR PRODUKT ALI GA VI PRIPOROČATE PROSIM odgovor i stvarno lepo delavnico imaš pozdrave iz Slovenie

Excellent.. bright idea..

good job but i believe heating it with heating torch helps a lot also

love it your tools sir

Fantastic!. But where to get those wheels?

Muito bem explicado. Parabéns

Excelente ideia , grato.

where did the round discs / pullys come from?

How do you make the dies?

Svaka cas odlicna masina i dobar tutorial kako da napravimo 💪💪💪

Exelente maestro muy bueno

😍😍😍😍

Nice uploaded frends

Un verdadero maestro ordenado y muy didactico

You should install this in a separate solid metal stand.

How're Parkside plants?

Is this guy working inside a hardware store? 🤔

Bro I think you crazy and love with tools

Looks like it would kink some thinner walled stuff though.. maybe if you took another pulley any cut it in half to use as the support part..

dads gonna be pissed ha ha bending his pipes up lol jp

Not convinced

It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes. Otherwise I like how it has degree markings capabilities.

nice but does it work properly on hollow pipe??. I mean clean bend??

where do you get the pulleys from?

What is the name of that pulley sir..how can i buy that....thank you

Q gusto de ver q tienes tantas herramientas me gusta.👍 pero mis respeto para el, q lo ase sin tener muchas herramientas.

Excelente video felicitaciones👍👌👍🙏🙏🙏🇦🇲🇦🇲🇦🇲

Yet another DIY'er who uses a vernier gauge as a scriber... puts me off straight away.

Nice, where do I get the wheels ?

Good job. Did the steel need any hardening? Is it ordinary steel?

Excellent brother.. like it