How to Build a Wireless Corne Keyboard

День тому

This video will go through all the steps to build a wireless Corne keyboard, from ordering the parts, building the physical board, and of course flashing the firmware with ZMK. The steps shown here apply to both the low profile Choc and MX variants for the Corne. The board uses Choc White switches which feel pretty good although I still prefer Choc Robins for clicky switches. This board also uses Nice View displays which use very low power draw making them perfect for a wireless build.
The board shown in this video was provided by Typeractive, run by Nick, the creator of the Nice Nano wireless controller. I highly recommend if you decide to build a wireless Corne, get it from Typeractive. They have a really nice 3D configurator that gives you a real-time preview of what parts you'll be getting and makes ordering everything a breeze. You can find the board over on their website: typeractive.xyz/scottokeebs
~ Links ~
My Keyboards: keyboards.scottokeebs.com
My Shop: scottokeebs.com
Merch: merch.scottokeebs.com
~ Handwiring Tools ~
TS100 Soldering Iron: amzn.to/3LCsrkb
D24 Chisel Tip: amzn.to/3VFxiES
63/37 Solder: amzn.to/3uBlMPu
~ Handwiring Parts ~
1N4148 Diodes: amzn.to/3Ccljbb
16g Copper Wire: amzn.to/3xLDVvJ
Raspberry Pi Pico: amzn.to/3HglCVb
Arduino Pro Micro: amzn.to/3HkR9Fn
Ethernet Cable: amzn.to/3uyaOKr
M2x6mm Screws: amzn.to/3UI1bDH
M2x8mm Spacer: amzn.to/3Y4KzJ3
M2 Heat Set Insert: amzn.to/3WjklB9
Durock Stabilizers: amzn.to/3FgcLQR
~ 3D Printing ~
Ender-3 Pro: amzn.to/3VIWryL
PEI Magnetic Bed: amzn.to/3Hi7URx
Dual Z Upgrade: amzn.to/3h7DTJy
BLTouch Auto-Leveling: amzn.to/3UGEBv8
~ Favorite Cheap Switches ~
Gateron Milky Yellow: amzn.to/3Bk0Cci
Akko Lavender Purple: amzn.to/3VJy440
~ Social ~
/ joe_scotto
/ joe_scotto
ko-fi.com/joe_scotto
~ Community ~
ScottoKeebs Discord: / discord
Handwired Keyboards Reddit: / handwiredkeyboards
~ Timestamps ~
0:00 - Intro
0:32 - Typeractive
2:38 - Parts
4:18 - Controller
6:30 - Display
7:19 - Unsocketing
8:20 - Battery
8:53 - Switches
9:35 - Assembly
10:35 - Firmware
12:57 - Flashing
13:41 - Pairing
14:19 - Typing
14:36 - Outro
~ Disclaimer ~
Some links may be affiliate links where I will make a small commission.
#corne #mechanicalkeyboard #zmk

КОМЕНТАРІ: 174

@yisus_christ 6 місяців тому

By far the best tutorial out there for Wireless Corne build! I'm building mine in a few weeks and I will definitely follow this guide.

@lunchboxtml Рік тому

Back in my day a wireless Corne meant we had to add bodge wires, used OLED holes for battery connectors, and hot glued our power switches on xD. This PCB you used here is really great.

@andyshow1817 11 місяців тому

Awesome video dude. Super informative and very high quality. Really appreciate your guides.

@TheNicell Рік тому

Perfect breakdown and step-by-step tutoral! Thanks for all your effort, Joe 🙌 Oh and production quality on point as always 👌

@joe_scotto Рік тому

Thanks Nick! I love the board and still super impressed by the case print quality :)

@tihroflan Рік тому

Man, do I love your tutorials. Everything's crystal clear and you are very calm. Puts me in confidence for when I'm gonna solder my next keyboard :)

@joe_scotto Рік тому

Makes me happy hearing my videos help :)

@RickWeberEcon Рік тому

Now I wonder what a panicky tutorial would be like…

@tihroflan Рік тому

@@RickWeberEcon I did not meant by opposition to a panicky one, but rather a frantic one, where everything is crammed in 5 minutes or so, as if everyone was an expert (as if experts needed tutorials).

@kraxen72 11 місяців тому

typeractive and zmk look awesome! i've built a wired kyria 1.4 but this is just on another level with how easy it is

@jackshafer9161 10 місяців тому

Joe, your video guided my Typeractive build. Thanks so much.

@winter-nu5wf Рік тому

I saw that site before but have never soldered anything for keyboard builds so I was having a hard time visualizing how everything would be done. Other tutorials would just straight up skip to the end portion or not include what you had in this video. Thank you for the detailed guide, now I know what I'll be doing one of these weekends :))

@joe_scotto Рік тому

Glad it was helpful :)

@piyiotisc Рік тому

This is the best tutorial I’ve seen! Amazing content. Subscribed

@kevinchang0527 Рік тому

Been watching some of your videos. You totally deserve a lot more subs. You basically taught me how to hand wire kbs from scratch, though I still haven't had a chance to get my hands on one. Just want you to know you're doing great and people like me appreciate your hard work.

@joe_scotto Рік тому

Means a lot to me when I hear back that what I’m doing helped someone, it’s the reason I do it :)

@shahnurislam5100 Рік тому

Thanks Joe, I was a bit overwhelmed by what was needed and this perfect!

@joe_scotto Рік тому

It really is a lot simpler than it seems, glad I could help :)

@somedudewithakeyboard 6 місяців тому

Great tutorial. I already have Cornish Zen. Now I can build this one for the office.

@michaeltaylor4817 Рік тому

3d printed keyboard with an intergrated track ball next please. i wanna get a 3d printer just for that

@NathanHedglin Рік тому

Same!

@bezwong 10 місяців тому

The trackball from keyball series from yowkees or corne keyboard from eiji onchi would be awesome. Also possible to add a similar joystick module from gmk on the motherboard?

@german_class_videos 9 місяців тому

You know what in effort and money- it's actually that mouse which will take more time and keyboard will be flipping fast to make compared to that

@somebody_on_the_internetz 6 місяців тому

You mean like the Charybdis?

@michaeltaylor4817 6 місяців тому

@@somebody_on_the_internetzdidn't know about that... cheers

@mariofeared Рік тому

Great tutorial as always. I just got the prints for the ScottoFly and Scotto36 ready. Waiting for the diodes to arrive in the mail so I'll probably be building them through the weekend.

@joe_scotto Рік тому

Hell yeah! If you’re not in the discord already, join up and ask any questions you might have :) discord.gg/vN6X3z8eyv

@mariofeared Рік тому

@@joe_scotto Awesome! I'll join right away. Will probably have to do some changes to the layout to fit the current one I'm using (Swolemak-dh , a Swedish variant). Plus I want to add a layer or two with my most used macros for Blender, Maya and Zbrush. See you then!

@disarmyouwitha Рік тому

I love these new Typeractive PCBs =] I bought 5col and 6col choc spaced~ Though, once I get my printer up again, I’d like to print a case that is basically the switch plate, instead of “tray mount” like it is now~

@EricMuranoAU 11 місяців тому

Wonderful and informative. Thank you so much!

@Cedutus Рік тому

Personally the way how i remove socketed controller is putting a long object from the front, into the back so that it goes the whole length of the controller, and lift it straight up. I usually use a metal spudger from my iFixit kit, but semi hard tweezers for me too doing this.

@sehunhan1195 8 днів тому

no one mentioned this, but in the video Joe said he was going to order ez solder hotswap sockets/headers. However, in the actual build, he used mill-max hotswaps. EZ solder has the black plastic case on the headers, and the mill-max hotswaps are just pins that you solder, just like Joe did in this video. Just a FYI

@Sgroh87 4 місяці тому

I haven't used a choc style board yet, but when I'm putting together a regular board, I like to put all the switches into the plate first, and then try to attach it to the board. That way, they are all snapped into the plate before I get it plugged into the board.

@3dkeycap Рік тому

Great video! thanks for sharing. Maybe I could send you over some of our keycaps for you to try them and showcase them in a video?

@esoel 4 місяці тому

Thank you very much, this was extremely helpful to build my lily58, it's better than typeractive's own instruction videos. Really appreciate it.

@mikewinanz428 Рік тому

Great video Joe!

@bart9522 10 місяців тому

Mind blown how comfortable they made this.

@grinder_. Рік тому

What are the odds that I searched for this video literally 30 seconds after you uploaded it, good shit

@joe_scotto Рік тому

Damn! Glad you found it :)

@Diamond-rs1jz Рік тому

same

@davidwoods1337 11 місяців тому

Great tutorial! What do I search for to find those nice pin headers and loose pins? I've never seen loose pins like that before.

@TheD3adlysin 8 місяців тому

Tell Nick that I found his website from here and ordered the wireless today. Fast shipping.

@legolator Рік тому

Great build, neat site. Too bad as a European I can't get the battery with the kit, which is a bit silly because I can certainly google the product and have it shipped from like China but not in a kit from the US. Been thinking about building a smaller keyboard after using a Moonlander for about a year and a half now, and the Corne or Lily58 are both on the short list.

@TanningCat Рік тому

Thank you! I was just about to buy one! This will be very helpful when it comes.

@reygalendez4497 9 місяців тому

Idk if you already have it on your newer vids but a 3d printed switch fork will really help with installing tHE SWITCHES

@joe_scotto 9 місяців тому

A what now?

@nidusa1 Рік тому

I think it would be better to put the silicone rubber protector back on the Tweezers Before using it to pry your IC chip. all tweezers come with free silicone slide on protector. don't throw those away.

@alexmelillo1247 Рік тому

Pretty cool

@Iamsylar567 7 місяців тому

Hi, how does it feel to reach inner thumb keys . Any recommended keyboard that have thumbs a bit outward ?

@jamlab13 10 місяців тому

any recommendations on how to configure layers + underglow in ZMK? Useful when I'm home and plugged in.

@gabdev Рік тому

Hi @joe_scotto! Thank you very much for the tutorial. Quick question, how did you make your MacOS terminal look like that? ( 11:03 ) and can I have your .bashrc file please? :3

@mdnlss 8 місяців тому

Does anyone know where I can find 3d print file for case? And are fr4 plates needed for this build?

@jakub2631 9 місяців тому

can you have RGB LEDs with a switch plate? or will it block all the light?

@matyhattam2458 7 місяців тому

Hey very Nice video ! But wanted to ask how long do the battery last without recharging ? Batteries seems so tiny

@joe_scotto 7 місяців тому

It depends on how much you use the board but I typically get 1-3 weeks on a single charge. You can use the ZMK power profiler to get an idea: zmk.dev/power-profiler

@mahfujahmad2097 Рік тому

can you make an explanation video on keyboard knobs?

@madvillany420 Рік тому

Great video, anyway you can show how you did the power switch? I am waiting for parts to do this and I’ve never done it before. Even an image of the board would work for me.

@joe_scotto Рік тому

The boards from Typeractive come with it pre-installed so you don’t have to do anything. If you go with a traditional Corne PCB, you basically mount the switch in the TRRS spot and then run your battery to that before going to the controller.

@Pawlo_83 Рік тому

Hey man, great vid as always. I finaly have time and will to build my first custom. I plan to make your scottoFly but I have a quite important question. Do you think puting foam into a handwired board is safe or potetnial fire hazard?

@joe_scotto Рік тому

Probably but you should definitely make your own judgement on that. I do know though that rubber would be a lot better of an option and personally have done it.

@aperturelytical6499 4 місяці тому

Since the Nice views are out of stock, can i assemble with all the other parts and update the framework with nice views when they are back in stock? Or is it a one time, thing ? Thanks for this great video. I'm definitely coming back when assembling.

@joe_scotto 4 місяці тому

Yeah, you can reflash the firmware whenever you want. You don’t have to have them from the beginning and can just add it later.

@GenellerNaranjo Рік тому

Thanks for the video! Quick question, in MacOS you have 4 at the bottom-left of your keyboard, on Linux/Windows you have 3, how do you manage that with these custom keyboards, also, does it support profiles and multiple connections so I can switch between environments? Or once you connect it to a laptop/device you can't pair another one?

@joe_scotto Рік тому

It supports multiple devices and profiles. Everything is configured in code.

@stiljohny 6 місяців тому

Nice Video, Would you recommend low profile keys vs normal MX? could you find keycaps for low profile with imprints ?

@joe_scotto 6 місяців тому

Depends on if you want something low profile or not, I can’t answer that for you. As for the keycaps though, you can find low profile ones with legends.

@GayMrMan 8 місяців тому

Where can I purchase a PCB with pre-soldered LEDs?

@fearthesmurfs 10 місяців тому

Have you thought about building an associated numberpad (also wireless)?

@carshoesch 8 місяців тому

I got a corne keyboard today. Is there a way I can change the layout to german? I only have the US shortcuts..

@maddyleaf 8 місяців тому

If I make the firmware the exact same way you do, it says "fatal error, repo already exists and is not an empty directory"

@blediankryeziu4429 Рік тому

Joe, this is so cool! I don't see any custom builds on your website for sale. The tutorial is over my head but I still would like this setup. Would you consider selling this keyboard?

@joe_scotto Рік тому

Shoot me a message over on Etsy, I do commissions and could build one for you.

@blediankryeziu4429 Рік тому

@@joe_scotto I will, thank you!

@gil2546 Рік тому

I have a similar build of a crkbd, but for no reason my screens are always off, I already tried reflashing, reset to initial configs, etc, but nothing works. Do you know how can I test my screens to check if they are ok?

@ChrisDeger 9 місяців тому

This keyboard looks amazing, I have a very sick curiosity with it, but I don’t think I want to drop that big of a price for it. Me being a cheap ass or not this is bloody amazing, looks sexy and I bet is way better for your wrists and fingers then a standard qwerty.

@RennanMendesSerenzaRennan 3 місяці тому

Is it possible to do a DIY keyboard with rgb? What is the problems to do that? and a hot swap how do I do that? U can recomend some content about it?

@peanutadventures Рік тому

I've been considering one of these keyboards, but I'm a little concerned about the layer mode and typing scenarios where you need to quickly mix up lowercase/uppercase letters, numbers, symbols. Think along the lines of passwords, css color codes, markup tags, etc. What's typing on one of these like in those situations?

@joe_scotto Рік тому

It’s very easy once you get used to it, I’ve done everything from coding to large write ups on tiny boards like this. I have a video that will give you an idea of the keymap I use: Tiny Keyboards Explained ukposts.info/have/v-deo/fZl5eG-LaZpnuok.html

@MAGAIVER Рік тому

I have a Corne-ish Zen, a fancier version of the keyboard on the video and I can type above 100wpm with numbers, symbols and punctuations it feels very seamless to me. Nut I've been using various tiny keyboards for 2 years and there is a period where it feels weird at first, but once you get the hang of it, it just feels right, highly recommended.

@pashley_941 7 місяців тому

Can it connect to multiple devices at once and switch between them?

@joe_scotto 7 місяців тому

Yup, I have 5 profiles setup on mine. You just have to change the profile and it will auto connect to the device.

@pashley_941 7 місяців тому

sick, is there any videos on doing that? also do you know if there's any tenting mounts for it instead of just having it lay flat@@joe_scotto

@cefarix 8 місяців тому

Hey I just got recommended this by the algorithm, and I know this isn't related to keyboards, but I think you should do a collab with Joe Scott just for the heck of it :D

@joe_scotto 7 місяців тому

I might actually shoot him a message and try, it would be funny lol

@kimjongoof5000 3 місяці тому

And what is the difference between using the nice!nano and a nRFMicro? Sorry, I am new to all this.

@ferbarret 6 місяців тому

What would be difference on price between a wired and wireless corne keyboard? Thanks, great video.

@joe_scotto 6 місяців тому

For the typeractive PCBs it would be about $50 less for a wired one. I’m not sure the QMK firmware would work without modifications since their PCBs are designed for their controllers. You can also just get a wired Corne kit from somewhere else, there are lots on the market.

@ferbarret 6 місяців тому

@@joe_scottoI'm looking for a corne keyboard, wireless and macro support, thanks for your quick answer.

@kimjongoof5000 3 місяці тому

Is the nice!nano open source?

@joe_scotto Рік тому

If you have any questions feel free to ask and I’ll do my best to help!

@content_appreciator Рік тому

I'm interested in building a corne cherry v2 because it seems like the v3 doesn't have the snap-offs to convert to 5 column. I can find the documentation for v2, but not the pcb files in the crkbd github. Do you have a go-to PCB file for the cherry v2, or another way to build a corne with 5 columns and mx keys?

@joe_scotto Рік тому

You’re correct, the V3 doesn’t have the snap off column… I made that mistake once and was stuck with a 6 column PCB. Everything below V3 should have the snap off column but you can also find them on other shops such as little keyboards.

@ambarcanonicco Рік тому

Thank you for the video! Is it possible to still use it wired on some computers?

@joe_scotto Рік тому

Yup. The way it works is that the left half is the master and the right will always be paired wirelessly to it. You plug the left half in to the computer over USB-C and it will work with minimal latency. If you happen to game with it, the latency will be the same as a normal keyboard since the wired half is the left.

@TheKzimmerman Рік тому

Do you know where I can find a Choc compatible TKL PCB?

@RamirodeSouza 10 місяців тому

Quick question: I don't like to worry about battery life, is it possible to use them wired? Since they both have 1 USB port I'm guessing I can't connect them to each other and then to my PC, I'd have to connect both to the PC independently.

@joe_scotto 10 місяців тому

The nice!nano controllers will wirelessly connect to one another on a split build and you can just power each one over USB, so yeah 2 cables. However you can also build the Corne with Arduino Pro Micros and a TRRS interconnect cable which you would only need one cable to the computer. That said, battery life is really good on the wireless builds. I get about a month on a single charge.

@jhpk Рік тому

All and all, thanks a lot, great tutorial, except the colors you choose. 😂😂

@PonderingJosh Рік тому

I noticed the links for Arduino and Raspberry Pi controllers, would the DIY change at all? I thought they all had varying pinouts. Would I be able to use Pis and get the same result?

@joe_scotto Рік тому

You would need either a Pro Micro or a Nice Nano, they share the same pin out but just matters if you want wireless or not. This is if you’re building a Corne, any other board you’ll have to figure out which controller to use and where to match the pins.

@ZenuelPvE 9 місяців тому

just wondering if its possible to add a joystick onto this bored ? to make it useable as a game pad like the razer tartarus v2 as well as a keyboard

@joe_scotto 8 місяців тому

I'm not sure if you can with ZMK but I know QMK supports pointing devices: github.com/qmk/qmk_firmware/blob/master/docs/feature_ps2_mouse.md

@ZenuelPvE 8 місяців тому

@@joe_scotto ty for letting me know, i'll have a look into it

@ipfaffy Рік тому

If only nice!views were in stock anywhere, including typeractive

@joe_scotto Рік тому

Yeah they’re hard to find. Makes me super happy that I got a set haha

@chrisrod6501 Рік тому

Do you have to seat the nice nano faced down? Or can i face it upwards to be displayed through he acrylic. I am not using the nice view.

@joe_scotto Рік тому

You need to confirm with the PCB you’ll be using that the pins match, that will determine the face orientation.

@flowerrin6835 6 місяців тому

hey joe,I'm quited interested to get one wireless corne for lay down coding, under which situation my legs will be between two splits.Wanna ask if you encounter any connection issue when something in between two halves.

@joe_scotto 6 місяців тому

You wouldn’t have any issues with your body being in the way of the halves.

@flowerrin6835 6 місяців тому

thanks!@@joe_scotto

@ianliu88 Рік тому

Was hoping for a 3d printed hand wired

@Spinachomelette Рік тому

Hey Joe, Do these boards come hotswap or do we solder the switches on?

@joe_scotto Рік тому

Depends on the Corne variant you get but the one from Typeractive comes pre-soldered with Choc hotswap sockets.

@mikewinanz428 Рік тому

You can purchase the Corne from Typeractive with MX or Choc pre-soldered hotswap sockets.

@max_game_ua 2 місяці тому

I'm to build this KBRD but my oled not working. In config uncommet CONFIG_ZMK_DISPLAY=y. On internet not found unswer. You can HELP PLS.

@ClayTheFoxx Рік тому

OH SHIT THIS LOOKS SO SLEEK

@duaneward925 10 місяців тому

I like it I. Really really like it. You work is beautiful. I love it. Please bro please do some pushups every once in a while. Really though I like and subscribe.

@Goooogle Рік тому

That website looks sweet! I have a question for you: When it comes to tiny keyboards, which do you find more comfortable, low profile keys or high profile keys?

@joe_scotto Рік тому

I like both but I would say that low profile switches are a tiny bit more comfortable. Feels like gliding over the keys if that makes sense

@GayMrMan 8 місяців тому

Will the code be the same on windows?

@joe_scotto 8 місяців тому

Setup will be slightly different but the ZMK code itself will be the same regardless of OS.

@wadeduvall7026 7 місяців тому

You didn't link the video with your keymap 😢

@nathanp3366 Рік тому

Will a battery fit under the nice nano without the sockets? As in, just with the ones it came with?

@joe_scotto Рік тому

It’s going to be Pi Pico.

@nathanp3366 Рік тому

What? It said in the video nice nano. I just double checked.

@joe_scotto Рік тому

@@nathanp3366 Oh wtf… my UKposts studio app showed this as a comment on my latest community post lol… A small 110mah battery should fit under the standard sockets if you solder it in place. The heigh difference is minimal.

@nathanp3366 Рік тому

Lol oh no worries I was just confused. Thanks so much for the info I really appreciate it. Getting ready to build my Lilly58 and was hoping I didn’t have to buy sockets too.

@joe_scotto Рік тому

You shouldn’t have to but I would really recommend socketing the controller. If you accidentally brick it or it somehow goes bad, desoldering them is a massive pain. With sockets you just pop it out and put a new one in.

@paologonzales4361 11 місяців тому

My country does not ship the battery and I am also not planning to build it with nice view does this works wired? I am new to this so help is very appreciated

@joe_scotto 11 місяців тому

Yes, you could use an Arduino Pro Micro in place of the Nice Nano on most Corne PCBs. I would check that it works with the one from Typeractive but I know it does on all the other versions out there.

@paologonzales4361 11 місяців тому

@@joe_scotto I look at the part of the video when you select the MCU of the board and there is no arduino micro option there. I will also just rely on this video if I would build it but buying different parts can make the process different I think it will be very hard for me I dont want to waste it, do you have any suggestions other than typeractive to buy parts of a corne keyboard?

@roaba3581 10 місяців тому

can you still use it wired? my workplace does not allow bluetooth devices to be connected to our workstations, but I'd like it to be wireless for when I'm at home.

@joe_scotto 10 місяців тому

@roaba3581 Yup, if you plug in the master side then it will work wired. The halves communicate to each other over Bluetooth low energy regardless but the connection to the computer can be wired.

@qm3ster Рік тому

How long does the battery charge last in your eggsperience?

@joe_scotto Рік тому

About a month or two with daily use. Deep sleep does wonders.

@zskater1234 5 місяців тому

Isn’t there a pre built?

@L1Q 5 місяців тому

How long does such a tiny battery last?

@woomdawg 3 місяці тому

Could you use this board as a macro board?

@joe_scotto 3 місяці тому

If you wanted to, sure. There are better options for that though.

@woomdawg 3 місяці тому

@@joe_scotto First WOW that was a fast reply! Take my sub! I really like the form factor of this. I would be open to suggestions. I would like to assemble it my self.

@GayMrMan 10 місяців тому

I can just use QMK for the firmware right?

@joe_scotto 10 місяців тому

Not if you plan on building it wireless, you will need to use ZMK. If you do a wired build with Pro Micros you can use QMK.

@GayMrMan 10 місяців тому

@@joe_scotto Awesome! Thank you.

@GayMrMan 10 місяців тому

@@joe_scotto Where can I buy switches made for the Corne? I am looking for white keycaps with letters and japanese sub-script

@woofkaf7724 11 місяців тому

А антенны на плате разведены?

@googleyoutubechannel8554 7 місяців тому

Why does it show 96 wpm on the test when you were typing at less than 50 wpm?

@joe_scotto 7 місяців тому

It’s an estimate based on the speed I was typing, I sustained 96wpm for 15 seconds basically.

@mentalflow Рік тому

can you use vial for it?

@joe_scotto Рік тому

No. This is a wireless board intended for use with ZMK firmware.

@mentalflow Рік тому

@@joe_scotto thanks

@Algardraug 11 місяців тому

280 is kinda low for lead free solder :/ I rarely can go under 320

@joe_scotto 11 місяців тому

Yeah, that’s one issue with lead-free. If you can use it, I recommend leaded solder… it just works better.

@OmarLivesUnderSpace Рік тому

After seeing all these horrors I'm just curious what your mouse is 🤔

@ishaankapoor933 7 місяців тому

How expensive is this?

@joe_scotto 7 місяців тому

The parts cost about $200 USD but if you build it with Pro Micros and no displays, it will be more around $150.

@carson.captures159 Рік тому

Yayayyyyy

@joe_scotto Рік тому

🎉

@alexanderzdobinkov4577 Рік тому

Holy shit, your place is a dexter's hideout!

@TCSu 10 місяців тому

Take my money 🤤

@wadeduvall7026 6 місяців тому

Two things: you didn't actually link your layout video, and it looks like you set it to 60 minutes and not 30 minutes (If you even care).

@drfleka 7 місяців тому

And what is the practical use of displays on the keyboard? I only see them as power draining useless piece of junk. I might understand if the keyboard have RGB and display to give more to it, but this is just BS.

@joe_scotto 7 місяців тому

First of all, these aren't standard displays... they're nice!views that have very low battery drawn and were designed for wireless boards. In my opinion, displays are mostly useless but on a wireless board they're more useful as they display battery and connection status along with the current profile you're using. They also have another use in terms of design as they allow you to hide the microcontroller placement instead of it just being a blank spot.