How to Fix Rust Holes on a Budget Using Fiberglass - NO WELDING

  Переглядів 1,994,375

4DIYers

4DIYers

5 років тому

How to repair rust holes on your vehicle’s body panels using fiberglass. Now before I get into it, as a disclaimer, this is a budget repair and when done correctly can last for a very long time. However with that being said, if you are wanting to restore a vehicle properly, than this isn’t the repair for you. This is a repair where it can be done at home, doesn’t cost a load of money or require any specialty tools, and can easily clean up your vehicle. Fibreglass is strong, so it won’t fall out like a body filler even when using the reinforcement mesh. The two main concerns with fibreglass is that it doesn’t expand or contract like metal, so a repair maybe visible. And it may have bonding issues with steel, so both these areas will be covered in this video. I have used this method in the past for low budget daily drivers without any issues and it held up great despite living in an area where vehicles are exposed to harsh winters. #oemtools #rustrepair #fordranger
Surface Prep Sander Kit: mobiledistributorsupply.com/2...
Air Die Grinder: mobiledistributorsupply.com/2...
Amazon links for some of the products used in the video:
USA:
Chemical rust treatment: amzn.to/3onBdoE
Wax and grease remover: amzn.to/2M6xvCV
Fibreglass matting cloth: amzn.to/3ouzNsR
Resin: amzn.to/3iRTnxC
Short strand filler: amzn.to/3pm0lxD
Glazing putty: amzn.to/3iQiAbS
Etch primer: amzn.to/3qXvxUm
Filler Primer: amzn.to/3iQSOnT
Backing pad: amzn.to/3qUc5rl
80 grit sandpaper: amzn.to/36gsUF5
180 grit sandpaper: amzn.to/2Mwjr5i
220 grit sandpaper: amzn.to/3sZf5V7
320 grit sandpaper: amzn.to/2YfzAPt
400 grit sandpaper: amzn.to/3qOEO0G
600 grit sandpaper: amzn.to/3t020uP
1000 grit sandpaper: amzn.to/2YkJzmq
1500 grit sandpaper: amzn.to/3qTem61
2000 grit sandpaper: amzn.to/3iWGzWX
Polishing Compound: amzn.to/3omIghF
Wax and applicator kit: amzn.to/36xqYs7
Canada:
Chemical rust treatment: amzn.to/3osNlVK
Wax and grease remover: amzn.to/39nLn4F
Fibreglass matting cloth: amzn.to/3a1NhHa
Resin: amzn.to/3cdRfix
Short strand filler: amzn.to/3iSXDgG
Glazing putty: amzn.to/3pmn1Ob
Etch primer: amzn.to/3aaS5tE
Filler Primer: amzn.to/2NucGl5
Backing pad: amzn.to/2M71Hhg
80 grit sandpaper: amzn.to/2MtEjdu
180 grit sandpaper: amzn.to/2Yf6rUs
220 grit sandpaper: amzn.to/2YjmoJe
320 grit sandpaper: amzn.to/36cqjfi
400 grit sandpaper: amzn.to/3qVYXlK
600 grit sandpaper: amzn.to/2YhR9OJ
1000 grit sandpaper: amzn.to/36e2fZs
1500 grit sandpaper: amzn.to/3cfSJZx
2000 grit sandpaper: amzn.to/3pot4BF
Polishing Compound: amzn.to/36g3PKq
Wax and applicator kit: amzn.to/3sZXoF6
Website: 4diyers.com
Patreon: / 4diyers
Facebook: / 4diyers
Google Plus: plus.google.com/+4DIYers
Twitter: / 4diyers
Instagram: / 4diyers
Tumblr: / 4diyers
Pintrest: / 4diyers
Tools/Supplies Needed:
-grinder with cutting disc
-surface sander with 80 grit discs
-80 grit sandpaper
-180 grit sandpaper
-220 grit sandpaper
-320 grit sandpaper
-400 grit sandpaper
-600 grit sandpaper
-1000 grit wet/dry sandpaper
-1500 grit wet/dry sandpaper
-2000 grit wet/dry sandpaper
-sandpaper backing pad/sanding block
-chemical rust treatment
-wax and grease remover
-denatured alcohol
-clean lint free clothes
-plastic container
-paint brush
-stir stick
-fibreglass matting cloth
-2 part spot/glazing/finishing putty
-short strand fibreglass filler with hardener
-polyester laminating resin with hardener
-acrylic enamel single stage color matched paint
-black undercoating
-etching primer
-filler primer
-safety glasses
-latex/nitrile gloves
-respirator
-water
-bucket
-carwash soap
-polishing compound
-microfiber clothes
-painter’s tape
-paper
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

КОМЕНТАРІ: 1 100
@4DIYers
@4DIYers 3 роки тому
Due to many requests, here is the Amazon links for some of the products used in the video: USA: Chemical rust treatment: amzn.to/3onBdoE Wax and grease remover: amzn.to/2M6xvCV Fibreglass matting cloth: amzn.to/3ouzNsR Resin: amzn.to/3iRTnxC Short strand filler: amzn.to/3pm0lxD Glazing putty: amzn.to/3iQiAbS Etch primer: amzn.to/3qXvxUm Filler Primer: amzn.to/3iQSOnT Backing pad: amzn.to/3qUc5rl 80 grit sandpaper: amzn.to/36gsUF5 180 grit sandpaper: amzn.to/2Mwjr5i 220 grit sandpaper: amzn.to/3sZf5V7 320 grit sandpaper: amzn.to/2YfzAPt 400 grit sandpaper: amzn.to/3qOEO0G 600 grit sandpaper: amzn.to/3t020uP 1000 grit sandpaper: amzn.to/2YkJzmq 1500 grit sandpaper: amzn.to/3qTem61 2000 grit sandpaper: amzn.to/3iWGzWX Polishing Compound: amzn.to/3omIghF Wax and applicator kit: amzn.to/36xqYs7 Canada: Chemical rust treatment: amzn.to/3osNlVK Wax and grease remover: amzn.to/39nLn4F Fibreglass matting cloth: amzn.to/3a1NhHa Resin: amzn.to/3cdRfix Short strand filler: amzn.to/3iSXDgG Glazing putty: amzn.to/3pmn1Ob Etch primer: amzn.to/3aaS5tE Filler Primer: amzn.to/2NucGl5 Backing pad: amzn.to/2M71Hhg 80 grit sandpaper: amzn.to/2MtEjdu 180 grit sandpaper: amzn.to/2Yf6rUs 220 grit sandpaper: amzn.to/2YjmoJe 320 grit sandpaper: amzn.to/36cqjfi 400 grit sandpaper: amzn.to/3qVYXlK 600 grit sandpaper: amzn.to/2YhR9OJ 1000 grit sandpaper: amzn.to/36e2fZs 1500 grit sandpaper: amzn.to/3cfSJZx 2000 grit sandpaper: amzn.to/3pot4BF Polishing Compound: amzn.to/36g3PKq Wax and applicator kit: amzn.to/3sZXoF6
@mrobinson8190
@mrobinson8190 10 місяців тому
I am a professional fiberglass repair technician... and I just want to say that your video is the best example of a proper repair I've seen. Great job man!
@4DIYers
@4DIYers 10 місяців тому
Thank you so much, I really appreciate the feedback and kind words!
@markaraujo06
@markaraujo06 5 місяців тому
I would like to follow you so i can learn few fiberglass repair
@mrobinson8190
@mrobinson8190 5 місяців тому
@markaraujo8087 That would be great, you can anytime. I live in Eastern Maryland though, and I haven't made any videos yet.
@srs_lol
@srs_lol 5 років тому
Considering this was budget job as its intended purpose... this was a top quality job.. bravo 👏 👌🏼
@4DIYers
@4DIYers 5 років тому
Thank you :)
@blackhorse7553
@blackhorse7553 5 років тому
Agree!
@nidstang373
@nidstang373 4 роки тому
That's what I was thinking. In High School I worked for a well respected body shop and I can tell you that none of our body men put this much attention into their rust hole repairs.
@SK-pn1pe
@SK-pn1pe 5 років тому
I left my truck parked in front of your house.....so you can have something to fix for your next video. Its a win/win.
@4DIYers
@4DIYers 5 років тому
LOL, sounds like a plan!
@blackhorse7553
@blackhorse7553 5 років тому
Hahaha
@OfficerThumbs
@OfficerThumbs 5 років тому
Lmao
@theefranchise1299
@theefranchise1299 4 роки тому
🤣🤣.. cool, I’ll be next😂
@timosness3667
@timosness3667 4 роки тому
I will leave my truck to! I have a 98 f150 with rusted cab corners. Have at it buddy! Lol
@johnnyloizides7887
@johnnyloizides7887 2 місяці тому
Why can't all videos be like this. Perfect. Lots of clear explanations and details.
@4DIYers
@4DIYers 2 місяці тому
Thank you so much, really appreciate the kind words!
@kirkhall2099
@kirkhall2099 2 роки тому
Having been in the collision industry for almost 40 years. This was a very good video. There is just a couple of little things that could have been brought to light but overall amazing! The best I have seen on utube. You obvious have had some training in the field. I doubt the average back yard worrier well get the body work to look this good with black lol. You give a hick of a lot of important information and would recommend that people watch the video several times to pick up everything that you talk about. Thumps Up!
@4DIYers
@4DIYers 2 роки тому
Thank you so much for the kind words and feedback! No official training, my dad had a body shop briefly before I was born and I have some friends who work in the body body industry too. I just managed to pick it up here and there.
@LubaLuba1
@LubaLuba1 10 місяців тому
If something was lacking please tell us so we all can get it right.
@Evaldas65
@Evaldas65 3 роки тому
Just fixed a rust hole in my wheel arch using this method. Here are some tips for beginners from my experience: 1. Make sure to indent the metal around the hole. I forgot to do that step, and ended up with a slight hump in my repair area. 2. Don't use primer before using body filler, or atleast try it on a small area at first. I had a lot of issues with the finishing filler coming off in chunks, even after waiting for 3 hrs before using it after spraying primer. 3. Don't be afraid to use multiple layers of body filler. I thought I screwed up when multiple nicks appeared after sanding the filler, but as it turns out I just needed 2 more thin layers near the low spots. The key is several light applications of filler. 4. Look at the repair area from multiple angles when using the fillers. I thought that the area was level, but as I found out after applying primer the area was quite wavy. The longer you sand, the better your result will be. 5. Make sure your layers of fiberglass actually stick together. My front fiberglass piece, as it turns out, didn't stick to the back one, there was a gap due to the metal being in the middle. 6. When painting, make sure a big area around your repair area is clean. I now have multiple dust spots due to underestimating the paint area. That's about all of my tips. I like this method a lot, and hope to get at least 3 years out of it before the rust comes back, perhaps even more.
@StaticisStranded2
@StaticisStranded2 2 роки тому
Using a primer filler spray after applying/sanding body filler and glazing putty helps to smooth the surface. Then sand it again. Spray your 1st two coats of base and two coats of clear then wet sand and buff.
@kitjasabsgabs1830
@kitjasabsgabs1830 2 роки тому
If using phosphoric acid type product like Ospho, kleen strip etc it will kill the rust for good. No coming back. It's chemically impossible if you get it all. After decades in the restoration field I can say that if you follow the instructions and pit more time into prep and doing good job it will last a lifetime. It's all in the prep. Painting is the easy part. Get it looking great in primer and all else will be nice. Take your time. Weather and humidity can play havoc on times for resin, filler, primer or paint flashing. Another thing, the better products you use the better and longer it will last. Using kylon is ok but using CarRep 2k primer, paint and clear is way better for 24.99 a can. Has NO SHELF LIFE. Not like other 2k coatings no canister to rupture and then 24 hours of pot life. CarRep has really impressed me. You can use on small areas at your own pace. Not hurry up and get it all ready for coating cause you only got a small window of time. You can take your time and do a job right. I don't sell it I use it and it's a great product.
@phamtinkt88
@phamtinkt88 Рік тому
Thanks for sharing your tips. I am about to fix my car rust hole. I am just wondering how long does your fix hold up? I am hoping mine will last for at least 2 years.
@charlesbarr3561
@charlesbarr3561 11 місяців тому
Thanks for sharing your mistakes/learning opportunities. I'm about to start my project, maybe a little nervous about it...
@Evaldas65
@Evaldas65 11 місяців тому
@@phamtinkt88 the area where I used fiberglass seems to be holding up okay. The areas where I just sanded, applied rust converter and painted have come back with vengeance - I should probably redo it now. If you use this method, take my advice: cut as much rust out as you can, and replace it with fiberglass. Rust converter alone simply doesn't work due to rust being on the other side of the panel, sadly. Also, make sure to use quality paint. My clearcoat is cracking aswell at this point.
@stevenladich428
@stevenladich428 4 роки тому
Really enjoyed. Tons of great tid bits of info. No frills and no annoying music. Thank You!
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@hunteroldham7720
@hunteroldham7720 2 роки тому
I’ve got a 1994 Jeep Grand Cherokee we bought it knowing it would need some work, we discovered holes in many different parts of the body and in the floorboard I was originally going to take it to a body shop till I decided to watch some videos to see if I could fix it myself and sure enough this was the first video to pop up and now I’m only 40 dollars in and I’ve gotten all the holes taken care of thank you your video really saved me a few hundred bucks.
@4DIYers
@4DIYers 2 роки тому
Awesome to hear, glad I could help and thank you so much for sharing your experiences.
@gabrielpw
@gabrielpw 4 роки тому
I'm a junior in highschool doing an AutoBody collision repair program. I have an 08 Sierra with fender flares my dad threw on to ignore the rusty fenders. Most of the stuff in this video is pretty accurate to what we do in the shop ( commission based ). Besides using different brands/higher quality tools. This fix works, and it works well. If you can do it at home do it, its similar to what would be done at a shop for a much higher price.
@dreadpenguinlord340
@dreadpenguinlord340 4 роки тому
Thanks for the tip! I always wonder about the longevity of this sort of thing especially since I'll have to do it on an old car that does not have replacement parts available!
@jonathanyates5198
@jonathanyates5198 2 роки тому
@@dreadpenguinlord340 or you can buy a sheet of metal and make your own
@jeffrey4547
@jeffrey4547 5 років тому
ur the first guy i have seen to treat the metal so it will last longer
@smkngreene
@smkngreene Рік тому
This has been the most straight forward, and easiest video to follow on this type of repair. So glad I stumbled on it.
@brianbaker359
@brianbaker359 4 роки тому
Your fast forward portions are beautifully done, we get to see every detail of your repair in a reasonable time frame.
@4DIYers
@4DIYers 4 роки тому
Thank you so much, greatly appreciated :)
@sunshinem.7741
@sunshinem.7741 Рік тому
Clear and informative videos like this are incredibly appreciated! It's 3 years later, but I've got a 2005 Pontiac G6 with some rusting I want to repair before winter and this may be the method I go with. It'll be much harder on the lower trim area since there's more shaping and a plastic strip to account for but the car was only $1k so anything is better than nothing 😆 Love this car already though and want to make it last! Thanks so much for the fantastic walkthrough!
@arshia666
@arshia666 4 роки тому
This is the best tutorial video i have come across in my entire life! Thank you!
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@wadenvern
@wadenvern День тому
Best fibreglass tutorial on yt..Bravo dude!
@philklingensmith3179
@philklingensmith3179 4 роки тому
Wow!! What a wealth of info!! So many questions I didn't even know I had were answered!! Thanks for understanding the need for a budget repair!!! :)
@aeridyne
@aeridyne 5 років тому
I would call this an IMPROVED budget repair since unlike most you actually use a rust converter. Great video. Two thumbs up.
@4DIYers
@4DIYers 5 років тому
Thank you so much :)
@GoodnightMrDoback
@GoodnightMrDoback 4 роки тому
i like watching repairs like this, this is one of the best outcomes ive seen, the paint looks perfect for a rattle can job
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@BenjaminRiel
@BenjaminRiel 5 років тому
Great video, shows every step and I’m especially glad you mention the sandpaper grits every time because I find it sometimes difficult to choose what to use!
@4DIYers
@4DIYers 5 років тому
Thank you for the kind words and feedback, always happy to help :)
@NikosDIY
@NikosDIY 3 роки тому
This is the best video on the subject. With the best end result. Thank you.
@rgonnering
@rgonnering 4 роки тому
I am a complete nube when it comes to bondo. This video was invaluable. Thank you so much. Your result looks like a professional body shop did it. It is way beyond anything I was imagining. Awesome.
@4DIYers
@4DIYers 4 роки тому
Always happy to help and thank you for the feedback :)
@alvingordon233
@alvingordon233 3 роки тому
@@4DIYers . H vh do u x cry by fcc x DC, CB xx CB. CB
@okami3186
@okami3186 4 роки тому
Really enjoyed your entire video & commentary. :) Very thorough & detailed work on your truck. Looks flawless and fantastic.
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@daxinventor3542
@daxinventor3542 5 років тому
I watched this video twice. I will watch it one more time as this is what I need to do to my truck rear fender. I like the resin repair because if it is done right, it will last a very long time. Thanks 4DIYers great job.
@4DIYers
@4DIYers 5 років тому
Thank you for the feedback and happy to help out :)
@nursekelly2834
@nursekelly2834 4 роки тому
Feels like i'm watching a Chris fix it vid! Great job!
@gstjwright
@gstjwright 4 роки тому
What a perfectly explained step by step procedure, thank you. Keep up your good work.
@4DIYers
@4DIYers 4 роки тому
Thank you for the kind words and feedback :)
@GrozOutTV
@GrozOutTV 4 роки тому
This is one of the best underground DIY video and satisfying at the same time that the job will surely last a long time. I also did mine waiting on the resin to dry out, I hope mine turns out well.
@4DIYers
@4DIYers 4 роки тому
Thank you, I really appreciate the feedback :)
@ricknorth2365
@ricknorth2365 5 років тому
Budget repair explained and done professionally, well done thank you
@4DIYers
@4DIYers 5 років тому
Thank you :)
@AceDublB
@AceDublB 5 років тому
Exactly what I was looking for, thank you, very well produced. Lots of great tips and basic techniques for the average DIYer. Great attention to detail giving an excellent final product. You didn’t choose to do a spray clear coat. My 2009 Ford Escape right rear wheel well has a hole as almost every other Escape of that year.
@4DIYers
@4DIYers 5 років тому
Thank you so much for the kind words and feedback. Greatly appreciated :)
@morrisroberts5061
@morrisroberts5061 4 роки тому
Very detailed, very easy to follow. Thank you for taking the time to share this!....
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@shokojimhollingsworth3940
@shokojimhollingsworth3940 3 роки тому
Pro level "budget repair"!!! My budget repairs usually involve duct tape.
@4DIYers
@4DIYers 3 роки тому
Thank you so much!
@YULABEBE
@YULABEBE Рік тому
well done man, a wealth of information. And a budget title for what amounted to premium-like work!
@zanepolowek
@zanepolowek 4 роки тому
This looks better than most of the videos of people"professionally" repairing them with metal.
@j-psalmi8039
@j-psalmi8039 4 роки тому
Yes, it LOOKS better at first. When dealing with metal that is rusted through, the only way to beat it is to weld in new metal. Fiberglass is easier and most likely cheaper, but the repaired area will rot again, no matter how well done the repair is.
@zanepolowek
@zanepolowek 4 роки тому
@@j-psalmi8039 yeah but for $500 cars this is ideal
@4DIYers
@4DIYers 4 роки тому
@J-P Salmi, as mentioned in the video, when done correctly this will last for many years. A weld in patch can also rot out if not done correctly either. The key is removing the rust and then sealing the surface so moisture don't come in contact with the metal. I wouldn't post a video that was lying to my viewers.
@4DIYers
@4DIYers 4 роки тому
Thank you Bob :)
@TheMrMinePlaysHD
@TheMrMinePlaysHD 4 роки тому
@@4DIYers did the same to my car, it only lasted about a month. Guess sometimes it workes, sometimes it doesnt. Still great Video.
@80Matthias80
@80Matthias80 4 роки тому
Wow, you are extremely thorough in your explanation, well done and thanks.
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@kato64
@kato64 3 роки тому
That was a really great video. Well shot, and clearly explained. End result looked fantastic!
@4DIYers
@4DIYers 3 роки тому
Thank you so much for the kind words and feedback!
@friguy4444
@friguy4444 3 роки тому
What an excellent job you did making this `How to`video. Thank you for doing such a thorough job. I`ll be using this for my third attempt at DIY rust repair.
@4DIYers
@4DIYers 3 роки тому
Thank you so much!
@86angrybees
@86angrybees 4 роки тому
Being from California makes me so glad. I just got a 77 ford Quadra van that sat for 15 years, only some rust on the “gutters” and a hole in the a pillar.
@4DIYers
@4DIYers 4 роки тому
Not going to lie, I'm definitely jealous lol. I just picked up an 06 Ram from southern US and apparently it's only been in Canada for a couple years. Clear than trucks 10yrs newer, I'll have to make sure it's well coated for the winter.
@mtwseneca
@mtwseneca 3 роки тому
@@4DIYers Shoot that baby with oil inside every panel (punch holes if needed) and around the wheel housings in and out, do the underside body, then coat the brake and fuel lines. The design of the rear wheel housing on trucks allow dirt to be thrown up and lay against the fender lips to rot out as in the vid. Get oil in there and that will no longer be an issue. Psst. I live in the Buffalo area- probably the worst area in the world for salt roads and this system works. Mike
@fakiirification
@fakiirification 5 років тому
i did this on a ford ranger to patch a hole in the corner of the roof that had completely rotted away. job lasted 6 years and was still unnoticable when i gave the truck to my cousin and he wrapped it around a tree one night. fiberglass works, but you do need to be rather aggressive with your grinding, get ALL the rust out, or the cancer will just spread under the repair.
@extremewhitetail837
@extremewhitetail837 5 років тому
Wow! Great job man. You definitely have talent.
@4DIYers
@4DIYers 5 років тому
Thank you :)
@lawrencem83
@lawrencem83 3 роки тому
Your video is the best one I have seen yet.
@4DIYers
@4DIYers 3 роки тому
Thank you so much :)
@charlesbarr3561
@charlesbarr3561 11 місяців тому
Great video on a budget repair....done correctly. Thanks for explaining it so well. And yes, you did get that to come out looking great. Better than mine is going to look I promise.
@bobgreen3116
@bobgreen3116 2 роки тому
Fantastic video best video on repairing a rust hole out there. You explained everything that you did and the grit sand paper. I will be repairing my truck the exact same way. I only hope my truck will turn out half as good as yours. I watched this video at least 3 times. Awesome job and thank you for taking the time to help us out. God bless you sir. 🇺🇸🇺🇸
@4DIYers
@4DIYers 2 роки тому
Happy I could help and thank you so much for the feedback!
@TaintedMojo
@TaintedMojo 4 роки тому
Effective but very labor intensive. That explains why bodywork is so damn expensive.
@4DIYers
@4DIYers 4 роки тому
Yep it can add up pretty fast, even more so when top quality materials are used like on a restoration. You can easily spend $1000 just in paint supplies.
@alanballard7466
@alanballard7466 2 роки тому
I usually don't go out my way to make a comment but I have to give you your props you did an outstanding job I am so impressed with your work. BIG AL.👍
@4DIYers
@4DIYers 2 роки тому
Thank you so much, I really appreciate the kind words and feedback!
@dickweber9311
@dickweber9311 Рік тому
Thank you so much for an excellent video. I just finished a repair on the fender of my daughters 2009 Honda Accord similar to what you did in this video. I viewed the video over and over and step by step during the repair. It was invaluable to me along with the detailed list of materials. I really learned a lot.
@4DIYers
@4DIYers Рік тому
Awesome to hear! Thank you so much for the kind words and feedback.
@natemoss7437
@natemoss7437 3 роки тому
That was absolutely amazing from start to finish great work... I am now a new subscriber to your channel... keep up the great work and the videos
@4DIYers
@4DIYers 3 роки тому
Thank you so much for the feedback and support, greatly appreciated :)
@bensanger5409
@bensanger5409 3 роки тому
I think you covered everything here👍
@SladesVWBeetle
@SladesVWBeetle 4 роки тому
Wow you did a really nice job!! Thanks for the step by step process!
@JacobSteeg
@JacobSteeg 4 роки тому
I have a mustang with a salvage title, so I dont want to spend much money on it, but I want to get rid of some rust in the rear quarters. This video gave me hope that I could do it without a welder. Thanks! I am going to give this a shot this summer. Thanks for the comprehensive video!
@waygone6657
@waygone6657 5 років тому
Good job on the repair process and presentation. Keep up the good work. :-)
@4DIYers
@4DIYers 5 років тому
Thank you!
@chucklucas8747
@chucklucas8747 4 роки тому
Was about to repair my 07 ford rear fender glad I watched this now I am sure I can do it
@KollynJ
@KollynJ 4 роки тому
Chuck Lucas how’d it come out? Have same spot on 06 about to operate
@chucklucas8747
@chucklucas8747 4 роки тому
Have not painted the repair yet to much rain but so far so good
@jamesanthonyclemons8031
@jamesanthonyclemons8031 13 днів тому
I really like your videos. You do a great job with explaining your every step. Very in-depth ! I look forward to seeing more of your videos. I’m in the process of getting my 1979 K10 back in good shape. It’s a farm truck that is in good condition. But dose need some work. Your videos have been a great help. Thank you very much.
@4DIYers
@4DIYers 12 днів тому
Thank you so much for the kind words, greatly appreciated! Always loved the K10. Friend of mine still has his from high school, even survived a shop fire.
@emirlutvi3924
@emirlutvi3924 9 місяців тому
Determine to do it by himself. He yust don't want to weld and replace.. Respect to that.
@4DIYers
@4DIYers 8 місяців тому
Thank you so much!
@Tomsfoolery.
@Tomsfoolery. 5 років тому
Good job! That looks great for a budget repair!
@4DIYers
@4DIYers 5 років тому
Thank you!
@neanderthalgames9397
@neanderthalgames9397 2 роки тому
Wonderful video, I came in expecting a super sketchy fix, but this looks very good and hopefully will last a long time as long as the fiberglass doesn't separate from the steel fender.
@4DIYers
@4DIYers 2 роки тому
Thank you so much, I really appreciate it!
@fisenknan3981
@fisenknan3981 4 роки тому
This is the best comprehensive but easy tutorial for rust repair.
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@19frito
@19frito 3 роки тому
This is a great video tons of info and step by step instructions thanks for the details
@Despecialedd
@Despecialedd 5 років тому
This is the best bodywork video I’ve watched, amazing explanations
@4DIYers
@4DIYers 5 років тому
Thank you so much for the kind words :)
@juanpalos3657
@juanpalos3657 5 років тому
New subscriber to your channel ..... exellent work my friend you make it look easy. Very well done should last for a while. Shout out to you from Mexico
@4DIYers
@4DIYers 5 років тому
Thank you so much, I appreciate the kind words and support :)
@clivetheasshole2053
@clivetheasshole2053 4 роки тому
Excellent Video and it explains in detail what needs to be done to get your car looking new again
@4DIYers
@4DIYers 4 роки тому
Thank you so much for your feedback :)
@MH-rv3tf
@MH-rv3tf 2 роки тому
Nice job buddy I love a man that can fix things
@ptlpszt1
@ptlpszt1 5 років тому
Well done. Thanks for sharing
@4DIYers
@4DIYers 5 років тому
Thank you :)
@klogjo
@klogjo 5 років тому
Good job, I have been repairing rust with this method for years, never had a problem. I have customized many a metal car with carvable foam covered with fiberglass and filler, won first place full custom at Autorama with a 1967 Camaro. Had car for eight years without any problems.
@4DIYers
@4DIYers 5 років тому
Thank you so much for the kind words and feedback! Congrats on first place too. Any photos of your build?
@corruptedbrain6
@corruptedbrain6 5 років тому
pic or lie
@klogjo
@klogjo 5 років тому
@@4DIYers Where would I send them??
@klogjo
@klogjo 5 років тому
@@corruptedbrain6 I've been dealing with people like you my whole life, you look for flaws then drive away in a rusted out VW.
@klogjo
@klogjo 5 років тому
@@4DIYers I always cut out as much rust as I could, sand blasted area and finished up with Metal Prep, painted back side if I could. I always took lots of pictures as I worked.
@fischerrestoration
@fischerrestoration 3 роки тому
I did this on a 72 El Camino back in 82' The whole driver side rear lower quarter panel was totally rusted away. Same process as seen here just a larger area. It definitely works! Mine came out perfect and the final paint job was very impressive for one of my first paint jobs! Good memories! Great video!
@4DIYers
@4DIYers 3 роки тому
Awesome to hear and thank you! Any chance you still have that El Camino?
@fischerrestoration
@fischerrestoration 3 роки тому
@@4DIYers No I didn't keep it but I surly wish I had! I went on to buy and flip many many more vehicles after that one. They're like children I guess.. you raise them up well and let them go.. Thank you for your response.
@merlingaming4126
@merlingaming4126 3 роки тому
Dude that was super helpful and amazing work 🔥🔥
@jasontavares9617
@jasontavares9617 5 років тому
Amazing paint work
@4DIYers
@4DIYers 5 років тому
Thank you!
@Alex420DT
@Alex420DT 3 роки тому
im about to try this, thanks for the video
@4DIYers
@4DIYers 3 роки тому
No problem!
@rolandmetayer7210
@rolandmetayer7210 2 роки тому
Very GOOD video ! ! ! Thank you. Cheers from Canada, snow country. We KNOW RUST ! ! !
@4DIYers
@4DIYers 2 роки тому
Thank you to a fellow Canadian!
@extremereclusefallows5779
@extremereclusefallows5779 5 років тому
I like this technique. Fiberglass sticks to about any roughed up material. For big holes I use wire mesh, then fiber glass only as a base to lay Bondo. I use cloth as opposed to fiberglass matting. I allow the cloth to partially harden before placing it. Right now, I am using it to patch up the rubber out rear bumper of my Dodge caravan which was rear ended. Cracked the entire length. Only a patch job to avoid it falling apart.
@davepelfrey3958
@davepelfrey3958 5 років тому
Looks Great and good explanation.
@4DIYers
@4DIYers 5 років тому
Thank you :)
@alexwaweru2457
@alexwaweru2457 4 роки тому
Are you chris fix brother or what
@AhileyGusani
@AhileyGusani 4 роки тому
Cousin*
@jamieround2072
@jamieround2072 4 роки тому
aww that would explain where u got the itch to fix on rides... how old were u on the 1 st video fix u did... & what was the ride then.... & where do u see your self by the time u r chris fix's ( your cousin's ) age ......??? & what other future or now rides u have there now...... & what u r looking 4 ward to owning or fixing in the future there.............
@tongl274
@tongl274 4 роки тому
lol
@joselouru
@joselouru 4 дні тому
I’m at it right now and your video gives me the confidence and tips to finish my project thanks men nice job n video
@CCROSS5882
@CCROSS5882 2 роки тому
you could make a living out of this rust repair, especially on the east coast, nice work
@4DIYers
@4DIYers 2 роки тому
Thank you! I try to avoid rust as much as possible, it's what nightmares are made from lol.
@4DIYers
@4DIYers 4 роки тому
Tools/Supplies Needed: -grinder with cutting disc -surface sander with 80 grit discs -80 grit sandpaper -180 grit sandpaper -220 grit sandpaper -320 grit sandpaper -400 grit sandpaper -600 grit sandpaper -1000 grit wet/dry sandpaper -1500 grit wet/dry sandpaper -2000 grit wet/dry sandpaper -sandpaper backing pad/sanding block -chemical rust treatment -wax and grease remover -denatured alcohol -clean lint free clothes -plastic container -paint brush -stir stick -fibreglass matting cloth -2 part spot/glazing/finishing putty -short strand fibreglass filler with hardener -polyester laminating resin with hardener -acrylic enamel single stage color matched paint -black undercoating -etching primer -filler primer -safety glasses -latex/nitrile gloves -respirator -water -bucket -carwash soap -polishing compound -microfiber clothes -painter’s tape -paper
@johnf.hebert1409
@johnf.hebert1409 4 роки тому
yeah but which rust converter? twhats the brand?
@brizzell2101
@brizzell2101 4 роки тому
How much was this project. Budget ok but is it in my budget
@EricHines
@EricHines 3 роки тому
@@johnf.hebert1409 I believe it was Krud Kutter Rust Remover and Inhibitor.
@JT-un7dc
@JT-un7dc 3 роки тому
Would that surface sander work with a smaller pancake compressor?
@liberty5565
@liberty5565 3 роки тому
I was writing everything down then seen this comment. Thanks. Killer video my truck is worse than this because it's a 7 year old GMC.
@AB-C1
@AB-C1 2 роки тому
Excellent video tutorial! I need to do this on my E46 3series here in London England, rear arch and sill surface bubbles, so thanks for a great tutorial as I don't weld(as yet!)!! Lol 😅👍💪😎🏴󠁧󠁢󠁥󠁮󠁧󠁿 Ps. Definitely Chris Fix level video and I consider him the best tutorial guy on all things cars usually on UKposts and this was definitely up there on a par with his which is no mean feat! Hope you get loads of subscribers mate! 👍
@4DIYers
@4DIYers 2 роки тому
Thank you so much for the kind words and support, I really appreciate it! Actually I've been doing videos longer than him lol. Just recently upgraded my camera too so my new stuff is now a better quality.
@joefowler9600
@joefowler9600 Рік тому
I'm also here because my e46 (in.the uk) is bubbling on the rear arch. Did you ever do anything with yours?
@BigWhite002
@BigWhite002 Рік тому
That's a damn good budget repair. I plan to do the same but right after doing minor sanding on the fiberglass I'm going to hit it with bed liner because it is only a bush truck. Great video
@endlesstwisties
@endlesstwisties 4 роки тому
I don't think i saw a cheap repair looking close to this. I watched hundreds of videos with rust repairs these past months. I hope i will have enough patience and my paint prepared close to original to make mine just as good.
@4DIYers
@4DIYers 4 роки тому
Thank you so much for the kind words and feedback :)
@cathysmith3124
@cathysmith3124 4 роки тому
Wow It looks great, However for my 15 year old civic I don't think I will do quite as much as you did for this vehicle. But I did learn quite a few things, Thanks
@4DIYers
@4DIYers 4 роки тому
Always happy to help and thank you for the kind words :)
@don7777s
@don7777s 5 років тому
This we could get a list on everything we need so I can order it, and then watch the vid step by step as I go?
@13milespergallon63
@13milespergallon63 4 роки тому
Wow I am so impressed on how this repair turned out.
@4DIYers
@4DIYers 4 роки тому
Thank you!
@oldcars5547720
@oldcars5547720 4 роки тому
Very interesting video. Going to plug some holes in my rear door skins.
@harrybosch8972
@harrybosch8972 3 роки тому
Good Job, This must have taken him a long time to do. He started off in a t-shirt and ended up wearing winter clothing. This tells you that this project will take time and patience.
@4DIYers
@4DIYers 3 роки тому
Thank you! Lol, can be done in a weekend. I was doing this in my spare time over weeks and being in Canada, the weather can change pretty fast.
@lotuslotus718
@lotuslotus718 4 роки тому
The best most satisfying video ever. Perfect job.
@4DIYers
@4DIYers 4 роки тому
Thank you so much :)
@eduardogil8338
@eduardogil8338 5 років тому
Was expecting a cheap and easy way to fix it, I'm impressed definitely using this a guide
@4DIYers
@4DIYers 4 роки тому
Thank you :)
@BruceLyeg
@BruceLyeg 5 років тому
I bought all the materials to do this and had planned to do it over the Christmas holiday... didn't happen so I figured maybe on the long weekend... maybe next long weekend! Nice job, that turned out really well.
@4DIYers
@4DIYers 5 років тому
Thank you, I really appreciate the feedback!
@Squarebody1987
@Squarebody1987 5 років тому
Nice work and helpful thanks for sharing new subscriber here
@4DIYers
@4DIYers 5 років тому
Thank you for the kind words and support :)
@matthewkile8
@matthewkile8 2 роки тому
This is an absolutely amazingly well made video. Thank you and congratulations. Superb.
@4DIYers
@4DIYers 2 роки тому
Thank you so much for the kind words!
@curtisjackson7742
@curtisjackson7742 3 роки тому
That looked great when finished. I'll be following this video step by step when I go to do the fenders on my 98 k 1500! Thanks for the video
@4DIYers
@4DIYers 3 роки тому
Thank you and happy to help!
@ronaldlehmann6935
@ronaldlehmann6935 5 років тому
Good teacher-u-made it very easy to understand and learn-thank-you
@4DIYers
@4DIYers 5 років тому
Excellent to hear and thank you for the feedback :)
@noseyloft
@noseyloft 5 років тому
very detailed. thanks sir
@4DIYers
@4DIYers 5 років тому
Thank you!
@daltonschannel8405
@daltonschannel8405 4 роки тому
Thanks for this video. My sons truck needs this done. I've done some auto painting, clear coat & clear cutting & buffing but never any body work so this is going to be tricky for me but this video really gives me direction. Thanks.
@4DIYers
@4DIYers 4 роки тому
No problem, happy to help :)
@anthonygalic4707
@anthonygalic4707 4 роки тому
I never seen better. Great fkn job to spend the time and blend that so well is something special. Excellent work
@4DIYers
@4DIYers 4 роки тому
Thank you, I really appreciate the feedback :)
@tassap9355
@tassap9355 5 років тому
Awesome job!! Now I understand what mistakes I did haha
@4DIYers
@4DIYers 5 років тому
Thank you for the feedback :)
@kevinl1505
@kevinl1505 5 років тому
Great job. You have convinced me to never do this. So much work
@4DIYers
@4DIYers 5 років тому
Thank you! Haha, but hard work paid off and you get the satisfaction of doing it yourself ;)
@mikeneeley7960
@mikeneeley7960 2 роки тому
Beautiful Repair, paint match was spot on.
@JustinPSG
@JustinPSG 2 роки тому
That's the best "budget repair" I've seen. Unfortunately, I have 4 kids at home so the most valuable part of my budget is my time. I still repair the rust, but it looks nothing like this! I don't make it perfect, but it is perfectly acceptable
@4DIYers
@4DIYers 2 роки тому
Thank you so much for the feedback!
@XXX-qk2cq
@XXX-qk2cq 5 років тому
Very nice job. I really don’t think you had to make so many excuses. That fiberglass will last forever. If you went to a shop you wouldn’t get anything different unless you asked for welded in new metal, which would double the price. It looks like that fender lip had already been filled. I think you did a real nice job but one tip : be a little more generous with the smoothing filler. I always use a long stroke from front to back following the contour of the body with the spreader. When you use the short top to bottom strokes after time you will see these lines even though you sanded it smooth. I’m not a pro but have been doing body work for years. Nice paint!!!!!!!
@4DIYers
@4DIYers 5 років тому
Excellent tips and thank you for the feedback! I've been trying to figure out if the truck was painted at one point. I can't find any tape edges, orange peal and paint fading was very consistent, color matches perfectly, no dirt or surface imperfections, no overspray, etc. The only thing I found was a small run towards the top of the door jamb. Factory flaw?
@Calendyr
@Calendyr 5 років тому
Great presentation. How long would you estimate this all took in terms of work time? I am guessing it is a 2 day process overall?
@4DIYers
@4DIYers 5 років тому
Thank you! I would guess about 20hrs. My biggest issue is that I don't have a proper place to work so I waste a load of time taking out and packing up tools. Then I had to cover up the fender to protect it from the weather.
@Duaneschannel
@Duaneschannel Рік тому
Awesome video man, thanks for the amazing details of description throughout👌🏼
@4DIYers
@4DIYers Рік тому
Glad you liked it and thank you for the kind words.
@theefranchise1299
@theefranchise1299 4 роки тому
Great work, price wise, budget, final results, can’t even say budget.. looks very professional.. great work man looks awesome!
@4DIYers
@4DIYers 4 роки тому
Thank you, I really appreciate the feedback :)
Fix your rust at home with no welding. #bodywork #autobody
12:56
Garage Noise
Переглядів 66 тис.
How to Repair a Rust Hole with Fiberglass - No Welding!
16:55
Lakeside Autobody
Переглядів 639 тис.
Glue On Wheel Arch Rust Repair Panels w/ SEM Impact Resistant Panel Adhesive
18:59
Lower Fender Rust Hole Repair | No Welding | Fiberglass Cloth
14:32
Lakeside Autobody
Переглядів 513 тис.
How to Repair Rust Holes on Your Car Without Welding
7:00
Dylan Kowalski
Переглядів 680 тис.
Cab Repair Without A Welder? It Can Be Done! - Trucks! S8, E9
17:33
POWERNATION 2
Переглядів 318 тис.
Extreme Rust Hole Repair w/ Homemade Patch Panel - Part 1
19:52
Lakeside Autobody
Переглядів 166 тис.
The  Bondo trick you don't know...  Faster, Easier, Improved Quality !     DIY Auto Restoration
8:31
Guzzi Fabrication - D.I.Y Auto Restoration
Переглядів 731 тис.
How to Fix: Rust Bubble Under Paint from a Rock Chip Around WIndshield
12:11
How to repair rusted wheel wells on a Chevy Silverado part 1
23:41
HackNpackShop
Переглядів 1,5 млн
nissan 350z modified version #explore #relaxcrhb
0:10
relaxcrhb
Переглядів 39 млн
Рено ЛОГАН 20го века обзор🔥
0:22
IGORIAN TODAY
Переглядів 686 тис.
Dongfeng - лучшие китайозы на рынке ,😂
0:59
Cadrol&Fatich
Переглядів 2,8 млн