greetings friends - We are using PVC pipes of the threaded type - heavy class pipe - Blue glue for PVC pipes - How to repair PVC pipe - How to change a PVC elbow - Repair water leak - Repair broken pipe - Repair perforated pipe
КОМЕНТАРІ: 1 400
@DiVO4271Рік тому
Без движения не получилось, правая труба явно сдвинулась в гильзе в стенке. Нужно было сначала вставить горизонтальные трубы, а затем надеть на вертикальную. Это бы дало большую степень свободы.
@IvanTtofimovРік тому
И я не понял,зачем он так" сделал. Странное мышление у автора
@NikonGT1991Рік тому
@@IvanTtofimov это было бы по-русски, а он иностранец, поэтому не смог
@user-nu1sw2bk6lРік тому
Да ,у них мышление такое.Гляньте как пальчиками ,,вставил,, правую трубу. Что-то напоминает.
@fareast8352Рік тому
Если вставлять обе горизонтальные трубы, то сразу вставить вертикальную будет проще.
@drakon777ufaРік тому
Ого! Наши забежали! Чё так уже делают? Не паяют? Клей? А сколько атмосфер держит? Старею...
@_MuJIbIuРік тому
Проще было сделать сначала соединить противоположные трубы, а потом вставить в верхний отвод
@newclient384Рік тому
Лол, ты разве не видишь что он трубу спокойно подвинул вправо???
@Olg73454Рік тому
Точно ❗хуйней занимается
@user-qv7tw2oy9xРік тому
@@newclient384 он ее согнул фантастическим образом как бумажную...
@truelies77765Рік тому
@@newclient384 Лол, так тебя зовут?
@VladimirKorneev81Рік тому
Не совсем понятно, как он последнюю трубу вставлял? Он ее должен был жестко деформировать, тогда вопрос, не возникнет ли в ней трещина в месте перегиба. В общем на таких коротких участках так сгибать трубу очень плохая идея. Тем более трубы будут замоноличены.
@BetterYetРік тому
There would be less stress on the opposing pipes if you glued all three together at the same time on the upward motion.
@gregharrison7631Рік тому
I agree and if you noticed on the last joint he slipped the pipe back in the concrete which is not what the thumb nail eluded to
@E.L.RipleyAtNostromoРік тому
Exactly what I was going to say; no reason not to put both sides in first and then pull down slightly and put on the downward pipe.
@johnbaldwin2948Рік тому
The white guy always with the better idea... Exactly...heat them all up...then put ALL the ends in at the same time...it's the least amount of bending.
@MrKnutriisРік тому
Yes - and a lot easier.
@davedammitt7691Рік тому
@@johnbaldwin2948 yay. The racist has arrived.
@anatolyshestakov764Рік тому
Нужно было все три трубы одновременно соединять. Сначала нацепить левую и правую, потом верхнюю. Тогда правую не пришлось бы ломать.
@SERGUNCHIK.MoscowРік тому
И я про это ☝️
@albert4052Рік тому
Creo que la solución mas práctica ya la apuntan muchas respuestas y justamente es la que yo también había visto, y es pegar lado izquierdo y derecho y seguido el de arriba antes de secar.
@DS-vq4ceРік тому
Просто мастер тот ещё еблан
@VictorGravitРік тому
скорее всего он это делал для того, чтобы не нарушался слой клея
@user-cu8hm9yg8oРік тому
тогда бы ты комментарий не написал
@patrickcarleton3924Рік тому
The proper way to do this (if doing this method) is to heat both bottom lines, bend them down, connect them, then push up to secure the upper line. This should be called "what not to do". I've noticed others have stated the same thing after I commented.
@Jaybird-oo3ihРік тому
Agree and I did the same lol
@rmiller334Рік тому
Correct
@mikecurliss848Рік тому
When you do it your way you have to pull bottom pipe back first to clear the tee to end of top pipe. This causes the bottom pipes to pull out and if they dont pop out it's still not good to introduce air pockets into the solvent weld as you push pipes back in. With fast setting solvent doesn't go so well. Instead of heating pipe I would, instead, cut the stop out of a short coupling. Use it as a slidable device after connecting one bottom pipe to top pipe.
@patrickcrabtree3162Рік тому
You are absolutely correct sir
@James-bv4nuРік тому
But you have to be fast, and you have to push up before the two sides setup; because you might need to rotate both sides in order to mate with the top. If the two sides have setup, but the top does not mate, then you'll be in trouble. Perhaps there's a slow setting solvent that can be used.
@user-fu1jg3ql1oРік тому
А слабо в нижнем положении тройника вставить сразу слева и справа, а затем и надвинуть на вертикальную трубу. Меньше тело движений.
@user-or7is1tl3pРік тому
Слабо, не умно, российское : авось пронесло
@gonchar1424Рік тому
Мы не ищем лёгких путей)
@jesusch3000Рік тому
Muy buena técnica de limpiar y limar la tubería x adentro y x afuera. Es muy importante k muchos olvidan 👍
@saulhenaocastro1230Рік тому
La idea es real y efectiva el tubo de la derecha dobla pór el calór que lo ablanda, la esponjá contiené águá para controlar ĺa curva y poder trabajar, luego lo calíentas ý lo metes en la te.....la humildad al recibir un contenido es muy util, no te fijes en errores de edicion, gracias amigo.
@user-so6xd4wr7qРік тому
Для дренажа пойдёт, для напорного трубопровода это очень рискованно. Труба очень тонкая, после нагрева разрушается кристаллическая решётка, и в этом месте может появится утечка. Хороший мастер соберёт трубопровод сразу, до того как трубу замуруют в бетон, без всякого нагрева. Греют эту трубу только при демонтаже, чтобы сохранить тройник, отвод, или какую либо другую деталь.
@user-Dima599Рік тому
У заказчиков планы меняются
@DiVO4271Рік тому
Ну, строго говоря, кристаллической решетки у пластиков обычно нету, это аморфные полимеры. В остальном верно, структура их молекул и связей от нагрева может страдать и они могут становиться более хрупкими.
@borisboris7856Рік тому
Походу вы на монтаже не работали когда все трубы замурованы в стяжку а лучшие ,, друзья,, сантехника электрики слаботочники начинают свою паутину тянуть а за ими и бравые отделочники ставят перегородки из гипсокартона выбивая пулемётную дробь своими перфораторами и попутно дырявя системы отопления и водоснабжения.
@borisboris7856Рік тому
@@russkiyaziat1034 Не скажи , если сделано по технологии стоит отлично. По крайней мере у меня , 25 лет полёт нормальный !!! Правда полипропилен и клей американский. Первый который появился в нашем городе а потом паяльники и европейскийРРR пошёл.
@VitalikvrokuРік тому
Частичная мобилизация - это когда тебя призывают целиком, а возвращают по частям
@jorgeurrea9566Рік тому
Buen video, explicas muy bien este método, yo lo he hecho sin calentar los tubos, pero de cualquier manera hay que aprender todo posible método, gracias por compartir tus conocimientos
@bryansonda18976 місяців тому
Y como se logra sin calentar los tubos. Yo tengo una situación donde quiero poner una t en cpvc blue
@alejandrofuentes1966Рік тому
Gracias por tu aporte y tiempo excelente trabajo yo trabajo en plomería de albercas por cerca de veinte años y no tiene truco tu video es real yo lo he hecho varias veces cuando se rompe una tubería y tienes que acoplar solo calentando el pvc es la única opción . gracias por compartir tus conocimientos 👍
@fidelriveros6677Рік тому
Disculpa. pero no es la única manera yo también los arreglo con un cople solo le quitas la separación que se tiene en medio y listo
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@fidelriveros6677Рік тому
No existe otra forma
@luisenriquenorenamarroquin2430Рік тому
Muy buena la técnica para insertar la tele ahora ya la aprendí muchas gracias Dios te bendiga saludo de Perú city .....
@luisenriquenorenamarroquin2430Рік тому
Era la tee de tubería de media pulgada
@user-no2uj7hs8oРік тому
Ловкость рук и ни какого мошейничества...труба справа спокойно подвинулась сколько надо было....тут без накидной гайки и муфты с наружной резьбой не обойтись так будет правильно
@asumptioРік тому
Она не подвинулась, а согнулась.
@user-iu5pl7sr3kРік тому
И рукой прикрыл..
@odinrossi3353Рік тому
@@asumptio с таким перегибом она б уже не разогнулась.
@odinrossi3353Рік тому
А в чем проблема сначала параллельные трубы соединить, а потом перпендикулярно? Тройник подвижен ведь.
@old_falcРік тому
@@asumptio Этого мы не видели: согнулась или продвинулась. Но если бы ТАК согнулась, ... Это больше похоже на "переломилась" Дурят нас.
@lkn6400Рік тому
Вариантов масса! Каждый делает как может. Данный вариант называется,- когда коту делать не хрен,- он яйца лижет😁
@ShkiverРік тому
Да... и главное - правильно выбрать яйца.. чтобы неловко не получилось.
@gruporedencion8790Рік тому
Exelente con el calor se puede manejar la tubería fácilmente buen video. ..
@videoveovideoveoo9487Рік тому
si, pero lo debilita,,, pierde mucho.
@gruporedencion8790Рік тому
Nooo el pvc después vuelve a su estado normal yo lo e usado Muchas veces y me sorprende lo bien que queda muy garantizado
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@carlosraide4823Рік тому
Excelente explicación...Gracias.🙏👍
@user-fm3xl4sc3mРік тому
сначала две горизонтальные соединить а потом уже верхнюю,так было бы проще!
@old_falcРік тому
Для этого есть специальная пара: штуцер и накидная гайка. Специально для таких ситуаций
@Dmitry_StorozhenkoРік тому
@@old_falc вы считаете правильным хоронить в стяжке резьбовое соединение??
@old_falcРік тому
@@Dmitry_Storozhenko Ну да. А склейку, тем более произведённую таким способом, правильнее?. Да и не думаю, что это соединение будет замуровано насмерть: закроют лючком, возможно скрытым. Мне вообще не нравятся всякие попытки натягивания на говне шкурки... конкретно - технология показанная в сюжете.
@Dmitry_StorozhenkoРік тому
@@old_falc ну, лючки в стяжке вряд ли кто-то делает, если это стяжка. Да и вообще, склейка - лично для меня - дело сомнительное. Я отдам предпочтение пайке. Гораздо надёжнее, на мой взгляд. Никакой резьбы и склейки.
@Viktor_PertsovichРік тому
@@Dmitry_Storozhenko в Европе водопроводные трубы склеиваются при чем склейка гораздо лучше пайки... резьбовые соединения и я не стал бы делать в стяжку...
@alexivanov3716Рік тому
из раздела: когда коту заняться нечем, он яйца Лижит 🤪
@bedientvondeutschland1779Рік тому
Genius. Love this technique. You are like Sigfried and Roy but in one person.
@claudioparra4699Рік тому
Hola maestro buen día siempre Gracias Santiago 🇨🇱
@moabfoolРік тому
No. The fittings need 1/4 turn to distribute the cement to the joint properly. Do the following: -Dig the trench longer so the pipe can flex naturally without heating. -Cut the pipes as shown (buy a cutter and a deburing tool if you make a lot of these repairs) -Cut an arbitrary length from the T pipe. Make sure it's longer that 2× the depth of the fitting sockets. 15cm is more than long enough. glue the pipe into the T socket. Following the instructions on the glue can for twisting and hold time. -Take the newly made T assembled and glue it into the straight section of pipe, aligning the T pipes, again following the glue manufacturer's instructions. -Use a coupling to join the T pipe, again following the gluing instructions. If you've dug the trenches long enough the pipe will flex enough to fit the coupling in easily. And that's how you add a tee to a straight run of pipe without seriously weakening the pipe itself. For proper gluing the joint shouldn't contact water for 30 minutes to 24 hours depending on the pressure to be run. If a small trickle of water cannot be controlled by closing a valve some slices of white bread can be uses to block the pipe. Get the cheapest bread possible. Wad the bread into a ball and shove it several inches/cm into the pipe. When water pressure is restored the bread will dissolve in the water. Seriously it just basically disappears.
@SomeRandomdude857Рік тому
You seem knowledgeable with this much verbiage. Blue glue is hot set glue and cures in a few minutes.
@assog5737Рік тому
He doesn't know what he's talking about. Doing what he said is totally unnecessary and a waste of time and money. There is one thing I always do, no matter what clue I use. And that is using a primer. I've done thousands of these type of connections. And almost every time that I used a clue that stated that you don't need to use a primer. The connections failed within a few weeks. Plus with a primer you will get a chemical bond. And a physical bond.
@keithmarlowe5569Рік тому
2 thoughts. 1) The pipe appears to be polybutylene.and that would not work on pvc nor cpvc. 2) I don't think it actually worked here. The last glue up was obscured by his hand, and the pipe either bent into an impossible U shape, or it moved horizontally. Watch again and see if you see it.
@Dunlap413Рік тому
This is the way
@christosmakariou4574Рік тому
@@keithmarlowe5569 - I concur, perhaps the setup is a fake since the camera does not show more than a few square feet. The pipe did slip to the right most likely from the bending pressure and if this was a real long pipe embedded into a real all it would not do that. The hand obscuring the pipe is a red flag too. If someone wanted to teach someone how the difficult part was done right they would hide the pipe behind their hand.
@Alder.Galaz1978Рік тому
Buen video, la conexión correcta se hizo debido al resorteo del tubo derecho previamente suavizado con la pistola caliente.
@MikeTerry1969Рік тому
I would have done the two sides since they were already bent outwards, and then pushed it up on to the top leg.
@evs6328Рік тому
ппц... если трубы довольно быстро прогреваются, то надо было сначала добавить клей, потом прогреть левую и правую, одеть на них, потом на центральную... всё в один заход... чтобы не "ломать" правую.
@martinpaez608Рік тому
Aunque es una solución antitecnica. Admiro como logra hacerlo con tanta habilidad. No es fácil resolver esa configuración. Saludos
@fidelriveros6677Рік тому
Claro que sí es fácil con un cople y quitas la separación que tiene en medio cortas un o de los tubos y el cople lo colocas de forma corrediza y unes el tubo que cortaste y listo
@chesterchin6972Рік тому
Wrong order, should connect both bottom lines then the top would be much easier
@jesvansРік тому
yep
@TelhadebarroРік тому
Genial! Thanks from Brazil 🇧🇷
@user-vo4ij3wh9zРік тому
Здесь нет ни горизонта ни вертикали, это всё в полу (посмотри на капли они капают вниз ) а правая труба действительно хитрая , она двигается.
@vovaibraimoffРік тому
Он её заломал
@KremlynDreamerРік тому
Она не двигается, фен ее сделал гибкой
@NIMED77Рік тому
100%)
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@user-zr4on1ff9pРік тому
Надо сначала горизонт вставлять потом в вертикаль.
@user-zr4on1ff9pРік тому
@@user-uh3sh3uj6z одаренные сначала паралель потом пенпедикуляр.
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@user-oe1xr8lb4dРік тому
Лажа полная в конце видно было что трубка отодвинул ась в право а вот бывают в основном случаи что ничего не отодвинуть тогда нужно сразу все концы отогнать и все соединить сразу
@asumptioРік тому
Он ее согнул, а не отодвинул.
@koreanuncleslifenoteРік тому
좋은 기술을 배웠습니다. 감사합니다. I learned a good technique. thank you
@papawhelpРік тому
This is a great lesson on how to not work with pipe in tight places by someone who doesn't know what they are doing...
@petergravy6893Рік тому
The last pipe must have been very flexible or was pushed back!!
@B-M.BРік тому
The later, that's why he hides that end with that fabric in his hand.
@f1reguy587Рік тому
He fully kinked it, not how i would approach this type of repair here… but pvc water pipes are not used at all now, with mdpe fittings you can do fusion welding, theres also slip couplings for pvc which i have used in the past. Can get quite hard in confined spaces especially with concrete.
@roberttorres6859Рік тому
I think it creased
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@S.N.NovikovРік тому
я бы склеил сначала горизонтальные(по картинке) трубы, потом вертикальную. склеенная горизонтальная труба шевелилась с большим запасом из-за получившейся длины, тогда можно вклеить вертикальную без случайного перегиба.
@VictorGravitРік тому
Думаю, он так делал не просто так. Твоим способом нарушился бы слой клея, то есть его бы больше вышло из швов из-за боковой нагрузки.
@S.N.NovikovРік тому
@@VictorGravit , а перегнуть трубку как? проще? я не буду говорить о том что она была нагрета и стала мягче, но кто знает что в месте перегиба будет после остывания? микротрещины там или еще что... у меня нет таких материалов для эксперимента, но я все равно использовал бы свой метод))
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@carlosgomez2796Рік тому
Excelente video cuando todos Me gustaría saber y ver más videos acerca de trabajos con tubo de cobre
@fivestring4653Рік тому
Neat way to do it if you don't have compression coupling. Thanks for sharing
@voiceofraisin241Рік тому
When he connected the last pipe did you😅 notice the pipe slid to the right then back into place. This idea may work but this demo was bogus.
@JT_70Рік тому
I don’t believe everyone it slid at all. I believe he linked it the had to straighten out the link. Look where the pipe enters the masonry. The masonry is tight against the pipe before and after.
@meangreencarpetcleaners3558Рік тому
It also has to be hot as hell for it to stay so pliable for so long, and yet he calmly held on to it bare handed for forever 😲
@yansuboch4984Рік тому
Мне интересны обстоятельства, при которых трубы без соединения оказались в исходном положении.
@GanKoIvРік тому
Китайцы. Сначала создают трудности, затем их преодолевают.
@user-jm3ph1zt4w5 днів тому
Джамшут трубы прокладывал, а Равшан бетон ложил :)
@user-volk999Місяць тому
Ну где бы вы столько коментов написали -он не слесарь -он блогер😂
@extraterrestreorion578Рік тому
Muy interesante, calentando levemente el plástico es manipulable, practicaré está reparación para más seguridad, comentan que tal vez hay truco, pero hay que hacerlo para estar seguros.
@MarioHernandez-ej4vjРік тому
Interesante ese metodo, pero el calentar y doblar la tuberia ¿no la debilita en caso de que los liquidos que van a pasar esten calientes?
@bernardogiagnacovo9849Рік тому
Lo calienta para que pensemos que es la manera pero en realidad el caño está suelto. Un engaño!
@pedrochevez2090Рік тому
As others pointed out, as i too noticed, it would have been easier to first insert the two on the left and then shifting everything back up to the upper pipe. But since the person clearly moved the one on our right to make it insert they failed to live up to the title of the video by not moving anything.
@keithmarlowe5569Рік тому
I thought I observed the same thing
@jaimesilvaf.401Рік тому
Excelente! 👌👏👏
@boscobaracus1823Рік тому
Here's my take - A slip coupling is your best friend in this situation. No heat gun required and you can take your time with 2 part glue and primer and bevel your pipes properly. But hey what do I know, I'm just a master plumber.
@danielrxsantiavox2420Рік тому
Muy bien maestro Y si fuera tubo de pared delgada como se hace?
@GoldCisneРік тому
Saludos, necesariamente tendria que cortar las tuberias y usar Uniones o talvez ejecutar bocas a las tuberias ....
@jasonlambert5239Рік тому
2:35 that pipe clearly moved
@jesvansРік тому
it did, kinked the pipe = fail. he did it wrong anyway. i could do it without heating the pipes.
@zaxarispetixos8728Рік тому
@@jesvans how?
@jesvansРік тому
@@zaxarispetixos8728 side it on the left pipe, then the right pipe, then the top pipe. it will go.
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@user-hv6ur6us5pМісяць тому
Отличный пример. Про клей ПВХ впервые слышу, спасибо в будущем пригодится. Совсем недавно приходилось искать (пи@дить) трубы, искать сварщика, да и сварочные аппараты работали так что все электроприборы на нашей улице моргали как новогодняя ёлка
@pauloossaniРік тому
Good job! Congratulations! Initially I thought to be very difficult, but on final was simply. Thanks!
@StasEnsoРік тому
Мне аж глазам больно стало, когда он правую трубку заломил. Ведь напрашивалось же решение вставить две боковых, а затем одну верхнюю. Или для этого и задумка, чтобы комментариев больше было? :-)
@alexislimasanchez3110Рік тому
Ahora con uno de cobre porfavor 😃 excelente video
@Esuper1Рік тому
Con los de cobre limas el pare de un lado de la pieza para que se deslize pasa el medio o centro de la pipa y despues la deslizas hacia la otra pipa al mismo tiempo que unes la pipa vertical. Hay un video de alguien que lo ensena por ahi.
@alexislimasanchez3110Рік тому
@@Esuper1 muchas gracias por la información 👍☺️
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@r.kkarigar2473Рік тому
Good job very nice job very nice thing very nice enjoying a very nice tools very nice finishing
@1LongrangerРік тому
A very high standard of plumbing work. Most just couldn't care less.
@STARDRIVEРік тому
If the T had the same diameter as the pipe, one could slide sockets over the joints instead. But even with this thicker T you could glue pieces of pipe in the T first, and then use sockets.
@mikevolante7663Рік тому
That would not help, but, I'm sure he moved the last pipe, watch it again
@user-ts9fs2xs9mРік тому
20mmとなっていますが、1/2インチと書いてあるので、13mmじゃないですか・・・
@holdanarmero39888 місяців тому
Con esa paciencia que coloca el pegamento ya me dio sueño.
@GoldCisne7 місяців тому
Lento pero seguro ..... Exitos a Usted .
@user-wq2ys6zi8oРік тому
Абра-кадабра, сим-саламин, сыла в волшебство однако
@user-yi8cr3lu2xРік тому
Правая труба двигается на ней не видно ни заломов ни згибов туфта.
@MrSolounРік тому
Doesn't heating the pipe to a temp that allows you to bend it like that cause it to loose its strength / pressure rating?
@terryramsingh472Рік тому
you may be right from a technical perspective. but for typical household pump pressure the cooled and hardened pipe still has the reliability we need. plus for years people have been heating and fitting pvc so its also a time proven method if you're in a bind. which I think is the point of the video.
@Ariel1SРік тому
No, it does not harm it. But you do risk kinking the pipe.
@frankbaublitРік тому
Nice job thanks for the video ❤
@tedmossРік тому
I like the way you covered the pipe with your hand so you couldn't see the kink you made in the pipe.
@rossprivate5456Рік тому
heat the 2 conduits that are in a straight line , bend them out slightly , glue the 2 ends of the straight conduits and slip the coupling/ tee joint on both making sure that the tee will align with the other conduit. heat up the conduits until they are flexible ,glue the 3rd conduit and then press the tee onto the glued conduit
@oswaldoarellano8927Рік тому
Al poner el tubo del lado derecho se ve claramente como se desliza para atrás y logra insertarlo a la T, entonces si todo fuera estado de concreto y nada se movería, no podría insertarse, tanto por ser un espacio muy reducido. Es un video mal hecho.
@GoldCisneРік тому
Como Usted diga, le agradezco el comentario. Nosotros estamos seguros del video que mostramos......Éxitos a Usted ...(Este trabajo es tan fácil que no existe la necesidad de hacer trampa)
@marcoguedes1434Рік тому
Ele enganou todos. Nao e assim que se faz.
@miguelangeldelgadillosilva7207Рік тому
Oswaldo Arellano te equivocas. El movimiento brusco que viste es porque por un momento la tubería se chupó pero la mano no permitió que se viera eso. Ya cuando insertó el tubo en la conexión el tubo recuperó su forma. Soy fontanero y a mí me ha pasado cuando hago esa maniobra. Quiero hacer hincapié en que -si defiendo este video- no es que yo tenga algo que ver con este canal y no conozco a la persona que hizo este vídeo pero sí puedo dar fe de que la maniobra es posible y reconozco ese movimiento brusco que percibiste y que malinterpretaste como un deslizamiento del tubo dentro del muro. Entiendo que no has tenido esa experiencia y por eso percibiste mal. Pero no pasa nada. Me es un placer aclarar el tema. Saludos
@kasu7639Рік тому
El tubo está caliente y de vuelve flexible, se tiene que trabajar rápido para que no quede deformación en el tubo.
@chukydroРік тому
@@kasu7639 exacto
@reynierpacheco3974Рік тому
Excelente aporte............
@MrMrMrMrMrРік тому
You are heating up the pipes so you make them flexible. That’s all. Which temperature? What kind of glue?
@MrTeff999Рік тому
You should always apply primer on PVC before applying cement - especially for PVC water pipes.
@chadlais1927Рік тому
Depends on the glue. Some doesn’t require primer
@rickbackous1041Рік тому
Sanding eliminates the need for primer.
@tommydian4722Рік тому
ukposts.info/have/v-deo/gaiLrKCGsaV_lIU.html
@wagnernogueira1033Рік тому
Muito bom! Se encaixasse os dois de baixo primeiro seria perfeito
@MauricioXDigitalArtРік тому
Pensei o mesmo kkkkkkk
@severofilho2911Рік тому
Até porque, dar-se impressão que o cano da direita está falso ( ele o empurra para dentro para ter o espaço...e o que eu vejo)...
@ignaciocorias4348Рік тому
Si es cierto.yo use esa tecnica para un tubo pvc de 100mm...y resultado es mismo..😃
@sebastiaoroquedelimaroque4411Рік тому
Show muito bom 👍🏾👏🏾👏🏾👏🏾👏🏾🇧🇷
@marcelo_rcostaРік тому
Excelente conteúdo! Muito obrigado por compartilhar.
@genomitchalinni8106Рік тому
I, for a time, helped to run eight PVC extruders. They made PVC things. We had a safety protocol to empty the machines of molten PVC during a " Black out". It actually happened once after a 5.0 earthquake. ( So. Cal). PVC, PolyvinylCloride, gives off a gas, that looks like smoke. It's called Tetra- hydrochloride. One "wiff" could collapse your lungs. Just a little FYI.
@anima_buonaРік тому
Это похоже на спектакль.. Мало того второй акт начался первым.))) труба, к ней подходит ещё какая то труба) Это кто так вообще делает?)))
@user-qw8qf1rq1zРік тому
Нужно вставлять все три сразу с нагревом правой и левой труб. Но если честно то такого способа соединения на холодную я не знал. Какие-то специальные трубы и соединения.
@mickobyobrien2650Рік тому
It would of been easier bending horizontal pipework down then connecting tee,heat pipe up again then pushed it up onto branch pipework.
@fernandovasconcelosdesousa6780Рік тому
Infelizmente o tubo não ficar este tempo todo flexível por causa do calor, ele deveria ter colocado os dois tubos da horizontal e depois o da vertical
@354walРік тому
Totalmente de acuerdo
@saulhenaocastro1230Рік тому
En una epoca todos los pegantes eran transparentes, una marca de pvc uso el azul para reconocer sus productos y asi responder por la garantia.....
@josueleon1435Рік тому
Eso depende de q pais seas seas en mi pais el pegamento de cpvc es amarillo y el tubo es color hueso no gris
@doubtingthomas736Рік тому
Ah.... now I know what to do if I ever see 3 pipes trapped in a little hole! 🤣
@gregalexandriaandstephan1797Рік тому
Что за клей?Какое давление выдерживает? Я в хозтоварах не видел.
@Boris_779Рік тому
Это термогидробарический суспензионный универсальный наноклей пролонгированного действия.....я тоже такой нигде не видел,потому.что я его только что придумал)
@johnglenham4099Рік тому
Be easier to use a slip fitting.
@rustynail9793Рік тому
I just want to know who was the genius that poured the concrete before making the connection
@bernardogiagnacovo9849Рік тому
Increíble que suban este video tramposo!! El caño de la última unión lo muestran como fijo en pared pero en realidad está suelto.
@AlexAlex-wf3mtРік тому
Чудным образом труба справа ушла в стену и вернулась обратно...тогда зачем весь гемор с прогдевами и чудной смазкой?
@Viktor_PertsovichРік тому
это не чудосмазка это клей...
@AlexAlex-wf3mtРік тому
@@Viktor_Pertsovich даже не сомневаюсь..и потому как трубы от температуры теряются в размерах,использую резиновые прокладки по старинке(ну кто-то премию получил за изобретение)
@Viktor_PertsovichРік тому
@@AlexAlex-wf3mt резиновые прокладки только в канализации хороши, а на горячей воде резина не долговечна
@user-mg4xb6yx7tРік тому
배관에 기초 지식이 없는 사람이 배관 하네요 이런 댓글 남기는것도 시간 낭비 하는듯 한데 잘못 된 지식을 올바른 방법을로 인식 할까봐 남겨요
@GoldCisneРік тому
우리는 서로 다른 건설 시스템이 있다는 것을 이해해야 하며, 다른 작업 기준과 무엇보다도 다른 자재가 있음을 이해해야 합니다. 인사말 .
@cristian10298 місяців тому
Pegamento glorioso ,,, sin el no hace nada y bueno para empesar el pegamento unos 500 pesos , la pinsa 1000 pesos y el calienta caños 😂 1500 y la hoja de sierra otros 50 , ,,,,, COMPRA CAÑOS NUEVOS😂😂😂😂
@josueramos4096Рік тому
Eu faria diferente, colocaria os dois tubos na horizontal e depois colocaria na vertical.
@isidroherreros6833Рік тому
Yo también, sería más fácil
@mikecurliss848Рік тому
Use primer. Then, wipe off excess solvent "bead" with a rag or primer dobber as the solvent continues to eat into the pipe until it cures.
@nathanhale7444Рік тому
I've never liked that blue "rain or shine" pvc cement. It always fails and I have to redo and redo and redo it. I've never had a joint that I've used the regular old clear stuff with the purple primer on fail
@Tim-FrenchРік тому
Ahh, this reminds me of when I used to lay piping on my property; those were the days!
@VIDEOAMANECERРік тому
Yo lo hice con soplete, quedó un poco deforme y quemado pero si se pudo 😁
@GoldCisneРік тому
Las primeras veces nos sale así, incluso muchas veces fallamos en el primer intento,,, es cuestión de poder practicar...gracias por comentar
@cursovirtualelectricidadРік тому
Parece interesante 🤔.........
@GoldCisneРік тому
Lo será
@samspade8612Рік тому
Brilliant! Excellent video.
@fabianbradaschia27978 місяців тому
Pareció tramposo la última parte, creo que al haber poco espacio se podría resolver con una unión doble
@albertothree5258Рік тому
Muchas gracias por el video , cierta vez me toco hacerlo y creo que lo hice mal , en mi pais solo existe el pegamento transparente y naranja ....que es ese pegamento azul ?
@GoldCisneРік тому
Espero le ayude el video
@user-mg4xb6yx7tРік тому
Hi_vp,hi_3p,pvc 계열은 열을 가하면 하자가 발생삽니다
@sergiogoicochea8272Рік тому
Pegamento para pvc OATEY azul u otras marcas en Peru
@user-hf1sx5ej4wРік тому
Пиздеж! Труба справа спокойно перемещается на этом видео!
@bruce350Рік тому
What a great way to destroy the integrity of the pipes, reducing their pressure capacity and increasing the likelihood of a leak!
@c.k.e.n.T.u.k2 місяці тому
1. Ничего себе, без движения))) 2. Проще было бы сначала нижние концы в тройник ввести и потом плавно завести всё на верхний ввод.
@ron5977Рік тому
Thank you, great video
@DesireeValcharРік тому
Should of did the 2 sides first than push up to the top. Looks like it crimped on the last pipe you put in. Almost like it broke. Thanks for showing!
@user-sb4sd7yb3jРік тому
Всё трубки вставлять одновременно. Так мне кажется лучше.
@user-gx5cu9mh9u2 місяці тому
Структура трубы при нагреве и загибах изменилась.Под давление такой узел нельзя ставить.На самотек пойдет.
@jamjary1195Рік тому
배관에 열을 가해서 꺽으면 내구성이 약해지고 나중에 터짐;; 누수관련 하자유투브 조금만 찾아봐도 배관이 얼마나 약한지 알수 있음