How to Make a Roll Wrapped Carbon Fibre Tube
Переглядів 1,079,455
День томуFull project details: www.easycomposites.co.uk/lear...
Further information and links ▼
► Easy Composites on Instagram @easycomposites
► easycomposites/
Products used in this tutorial:
► Easy-Lease Chemical Release Agent www.easycomposites.co.uk/easy...
► XC110 210g Woven Prepreg Carbon www.easycomposites.co.uk/xc11...
► XC130 Unidirectional Prepreg Carbon www.easycomposites.co.uk/xc13...
► Composites Shrink Tape www.easycomposites.co.uk/comp...
► OV301 Curing Oven www.easycomposites.co.uk/ov30...
For further details on this project, visit the project page on the Easy Composites website: www.easycomposites.co.uk/lear...
@cvspvr Рік тому
man, this company makes some really REALLY high quality tutorials
@raptordad6653 Місяць тому
I had the pleasure of speaking to Paul this afternoon about my project and the use of carbon tubes / wrapping carbon tubes around foam core to make a strong space-frame and the shear amount of knowledge and information he gave me was astounding!! Several really good ideas and new takes and new techniques I hadn’t even considered. I’ve ordered materials from Easy composites in the past for glider and boat repair work and I’m really looking forward to working with Easy Composites on this project too! Thanks Paul!
@easycompositestv Місяць тому
Glad we were able to help.
@dimosk7389 4 роки тому
"i am gonna be doing a very primitive test"...moves on and using an industrial press with a pc program that measures the force in detail...epic nice video btw
@easycompositestv 4 роки тому
Thanks Dimos. OK, so maybe 'primitive' was understating it a bit but what we meant was that we were not going to get right down into test standards and things, at least not in this video.
@mortenbakke2810 3 роки тому
a primitive test is also, often a stress it till it breaks kind of test, or destructive test just to measure maximum capacity:>
@Kr-oy2bo 3 роки тому
@@easycompositestv I really appreciate the tests at the end. I've worked with and used carbon fiber in the automotive race industry (Renault spec racers) and years ago we used to make some components out of carbon fiber, but i never really got to see it tested like this! We all know it's strong but hard to visualize sometimes. We only used it for Naca ducts and some basic non-structural things.
@snowleopard4689 3 роки тому
@@easycompositestv Before failure mode is achieved is the material in the elastic domain like steel would be before it reaches plastic deformation? Otherwise said, if the part is released from the machine after reaching 600kg at 10mm deflection would it still have the same dimensions as before being subjected to the test?
@mattlang5194 3 роки тому
Haha yeah it's primitive in terms of test design, but the equipment is $10-20k and up. I've done the same type of test with static weights to the same effect, though. You don't need the fancy tensile tester, but you would need to build up a fixture for the test.
@excessY 4 роки тому
Always amazed by the quality of your tutorials and products! You deserve a lot more subs !
@easycompositestv 4 роки тому
Thanks Youssef, haha, well, it's pretty niche stuff that we cover. If we were talking about Minecraft, Tik Tocking or giving away $100,000 to strangers then we might have a few more subs but when it comes to technical manufacturing there's only so many viewers out there!
@markrainford1219 3 роки тому
@@easycompositestv 0ver a third of a million views though. Almost viral.
@Depl0rable10 2 роки тому
@@markrainford1219 it's pretty impressive tbh but the number of people who need to learn to make carbon fiber AND don't work at a manufacturing firm who already makes carbon fiber is pretty slim unfortunately. Awesome videos, views aren't everything though
@joncraw29 4 роки тому
Thanks for another great video, I really wish they were produced more often!!
@easycompositestv 4 роки тому
Thanks Jon. Yup, so do we. We do have a more frequent release schedule coming up, hopefully we can maintain it.
@calebverdught 4 роки тому
Thank you for adding more videos. It’s great of you all to keep sharing your knowledge! It’s very much appreciated.
@easycompositestv 4 роки тому
Our pleasure Caleb, we have more coming and lots more ideas to share one they're done too. We really enjoy helping to explain these processes and share the information.
@northstar7694 3 роки тому
Thank you so much for actually showing some tests and discussing numbers even a little bit. Wonderful!
@easycompositestv 3 роки тому
Yes, agreed, more numbers would be good sometimes. They're not everyone's cup of tea so we don't tend to go too heavy into figures and calcs but we have at least a couple of videos in mind that will dive a lot deeper into material testing and comparisons. Stay tuned.
@tacg6799 3 роки тому
I was really fascinated by the tube and when he put it in the machine I nearly cried thanks for the video!
@TareqHamadallah 2 роки тому
omg I cried too😢🥺😂☺😘🤭😐🤤😪😐😏☺🤭🤪🥲😐😶🤤
@monono954 4 роки тому
Thank you for this, guys. I really appreciate this great material.
@easycompositestv 4 роки тому
You're very welcome!
@maker13matheson43 3 роки тому
This great info, and easy for beginners. A beginner's playlist would be a great addition
@benjaminrhodes9611 4 роки тому
Great video! Thanks for sharing all these different methods with us over the years!
@easycompositestv 4 роки тому
You're welcome Benjamin, thanks for watching over the years!
@papacapra1908 4 роки тому
It’s so pretty! I can’t wait to try and make body panels for my truck.
@AdamNZ 4 роки тому
same here
@Paul_MacK 3 роки тому
Good luck buddy
@bobsnabby2298 3 роки тому
Your truck weigh like 3 tons and you make light weight body panels for it !?!?!
@ovalwingnut 2 дні тому
I work for "Extremely Difficult Composites™" and 'we now realize' what we've been doing wrong all these years. Thank you!! You guys really R the "Carbon Fibre Whisperers" Cheers!
@easycompositestv 13 годин тому
Ah it's all in the name. 😅 Glad we could help.
@1Himiko7Toga 3 роки тому
Damn carbon is hella strong 💪🏽 that’s amazing
@agg42 3 роки тому
Thanks for adding those little tid-bits about how large manufactures might do things. I'm involved in manufacturing but not yet into carbon fibers.
@lucendi. 9 місяців тому
I used this video as inspiration to make my own aero bicycle seatpost and it works great. Thanks for these awesome videos!
@easycompositestv 9 місяців тому
Great to hear!
@dandeetorregosa4185 3 роки тому
I use that carbon tube for spacer for my bike stem.strong and very light.
@omegaelixir 4 роки тому
Love your content, it's amazingly information dense
@easycompositestv 4 роки тому
Thanks Srini, *information dense*; yes, I guess that's what we aim for!
@omegaelixir 4 роки тому
@@easycompositestv Yeah! Nailed it carbon bois!
@Sometimes_Always 3 роки тому
You guys make the best product videos..
@a330turbinex7 2 роки тому
Best composites channel! Congrats.
@easycompositestv 2 роки тому
Thank you for the really kind feedback!
@adr20sv 4 роки тому
Since the beginning of this channel, these are the best carbón fiber manufacturing videos around UKposts, no doubt. Keep the good work!
@easycompositestv 4 роки тому
Thank you very much Adrian, it's great to have had you on board since the start.
@andyvan5692 3 роки тому
great video, PS: for the novices among us a mandrel ( not a mandrill- monkey family) is a rod of metal you mount between centres in a metal or wood lathe to hold a round part securely ie a pulley or donuts shaped object, the rod holds the part by the inner bore so machining can occur on the outer surface ( otherwise gripped by a chuck, held at a centre, etc.) as this is the only way to hold it and machine successfully.
@dragerx001 3 роки тому
i like that you took time to show how to do it right :).
@irinavd0 4 роки тому
Nice to see you back guys!
@easycompositestv 4 роки тому
Thanks Alexey, we'll try to keep right up with our tutorial releases.
@titanracing7740 4 роки тому
Great stuff, are you guys also planning on a how to on making proper strong inserts in carbon structures? I'm quite worried about using aluminium threaded inserts inside carbon on structural parts. Would love to get to know a bit more about that and how to do it proper.
@easycompositestv 4 роки тому
Great suggestion! Certainly something we will look at for the future.
@jeff58353 3 роки тому
Thank you so much for the videos! I’ve learned a great deal watching your videos and really enjoy them. Is there a way you would suggest to add a raised “bead” to either end of a tube made in this fashion? Similar to the raised bead sections in the “complex carbon fiber tube” video. If I try and build an intake tube in this fashion I’d like to help insure that the boots would not blow off the tube.
@easycompositestv 3 роки тому
Hi Jeff, yes, you could do this very simply. Just cut a long thin strip of prepreg and then wrap that round and round as each end of the tube, making the tube considerably thicker in a 'bulge' at either end. This way the tube would still be parallel on the inside (so would release from the mandrel) but you'd get the bead detail you want.
@EnesMAkyol 4 роки тому
Amazing vid ! Thx for sharing information and ur knowledge
@easycompositestv 4 роки тому
Happy to help!
@andrew19682008 4 роки тому
Best carbon fibre video's out there! 👍
@easycompositestv 4 роки тому
Wow, thanks Andrew, we try out best :)
@andrew19682008 4 роки тому
@@easycompositestv you succeed! I will be after the kit to make the carbon fibre wings for my a5! Is that the same kit you used for the bonnet?
@easycompositestv 4 роки тому
@@andrew19682008 Yes, the process would be much the same albeit you may not need the inner moulding as we did with the bonnet.
@randallwatson391 4 роки тому
Great vid. Do you account for the thermal expansion of the aluminium mandrel when you consider what ID of the tube you want? I assume that the expansion of the mandrel "overrides" the contraction of the composite shrink tape. When calculating expected wall thickness do you assume that the consolidation will be more-or-less equal to that achievable using vacuum processes?
@easycompositestv 4 роки тому
For size critical applications you would have to take into account expansion at the cure temperature of the pre-preg. The compression provided by the tape ends up being similar or slightly greater than a typical vacuum bag. However, the fabrics can only be compressed by so much.
@MonoPedB 4 роки тому
This would be a great metarial to make a pair of crutches - light and strong.
@easycompositestv 4 роки тому
Yes, for sure. In fact I would be surprised if there weren't carbon fibre crutches on the market, somewhere.
@seannz100 4 роки тому
price probably isn't worth it, also considering aluminium ones are pretty light
@rootbeer666 4 роки тому
There ought to be a sport out there that involves crutches.
@markrainford1219 3 роки тому
@@rootbeer666 ain't that skiing?
@cycliststrainingpartner8877 6 місяців тому
And they always get stolen by the patients... lol @@seannz100
@javier7high 2 роки тому
Very inspiring video! Sparked so many ideas
@veoteveo1 3 роки тому
Hi Great Video! thanks for sharing... 1. f you had used the same weave of the one used on the ends for the destructive test would it have been stronger? 2 If you doubled the layer would the strength double? (is it proportional?) 3.If you would have machined rolled more tightly would it be stronger? 4. Would vacuum molding make the tube stronger during the curing than shrink wrap?
@Alfaduk 4 роки тому
Nice! Would love to see a video of how to attach metal to the CF tubes to help build frames or frame reinforcements, like a strut tower brace. An ultimate video would be how to create a CF antiroll bar, like the Porsche 911 GT2 RS uses............ :-D
@easycompositestv 4 роки тому
OK, thanks for the comments. We do plan to do a video on fittings and fasteners for making carbon fibre assemblies, we could cover some of the things you're talking about in that.
@justinwilliams1333 4 роки тому
Easy Composites Ltd showing us how to make a 90 deg bent tube would be nice also. How well does this pre prefer hold upto heat?
@junkandcrapamen 4 роки тому
@@easycompositestv I would love to know as well. I'm thinking of a homemade carbon bike with metal lugs.
@MyLonewolf25 4 роки тому
I’m gonna use this make a full carbon cold side for turbo setups😁
@GermanTopGameTV 4 роки тому
For the intake part that's a great idea, but I would not recommend to proceed past the compressor. Dimensions for the compressor housing need to be very precisely milled for it to work, and that takes a whole different level of manufacturing experience to achive. Like including thermal expansion rates, the mechanical deflection of the compressor blades at full speed versus low speeds, the whole 9 yards.
@joshgreaves9934 4 роки тому
What an awesome video! I’d wrap myself in carbon fibre if I could! Great stuff! 👍🏿👍🏿👍🏿
@easycompositestv 4 роки тому
Good plan. Maybe go for a lower temperature cure though?
@sinanparlak5446 Рік тому
beatifull video , congrats !!
@bradmaas6875 4 роки тому
Slight overlap, would that be 5mm or 10mm? For additional strength could more layers help? Rotational strength? You make it look easy. Thanx
@easycompositestv 4 роки тому
The overlap is only necessary to hold the fabrics together during the rolling process, so in this case the overlap was actually very small at around 3mm.
@sandman70131 2 роки тому
@@easycompositestv with the 5 total wraps around the mandrel, what wall thickness does this equate to after baking?
@easycompositestv 2 роки тому
@@sandman70131 The finished tube had a wall thickness of 1.7mm.
@GoldenSlothRacing 4 роки тому
What video covers making that tube with the kink in it? Can't recall seeing it. I'd imagine a similar process to the intake manifold you made though.
@easycompositestv 4 роки тому
Ahh, well, what we've done there is mention the 'other' tube video that goes with this one. We've already filmed it (which is how we had the video we needed for that shot!) but we haven't edited it down yet. We plan on publishing it next week. Once they're both up it will make a bit more sense.
@GoldenSlothRacing 4 роки тому
@@easycompositestv fantastic thanks for getting back to me! I can't wait as I feel it's very relevant for the projects I've got going on :D
@vinnbrock 4 роки тому
@@GoldenSlothRacing I'm glad you asked this. I've watched every one of their videos, and was wondering the same thing. Looking forward to the next video.
@millerchassis6119 4 роки тому
Can’t wait for that one I’ve always wanted to try making different tubes from carbon I tried different one off methods but turned out crap.
@hilmanikhlasulamal2826 Рік тому
I love your tutorial please make more🙏
@MadsonCCarvalho 4 роки тому
Very nice project! Thanks for share this precious information
@easycompositestv 4 роки тому
Our pleasure, you're very welcome.
@thegreekgeek176 4 роки тому
Could you make a carbon tube with a wet lay or infused process instead of prepreg?
@easycompositestv 4 роки тому
You could certainly wet lay in a very similar way to the repair done here and also similarly to a tube repair as seen in our Fishing Pole Repair Video. Infusion would be much harder in a practical sense for smaller tube sizes, although for bigger sizes it may work using a tubular bagging film and extra care to ensure the resin is evenly distributed all around the tube.
@jjackson3240 4 роки тому
You can also make your own prepreg by doing a wet layup on flat carbon and then freezing it. Then when you are ready to make your tubing, just let the home made prepreg thaw just a bit and roll it on just like factory prepreg. It's much less messy that way and the carbon tends not to slip as much during application.
@MusikCassette 3 роки тому
I would like to know, how much the carbon fiber weights per squaremeter.
@easycompositestv 3 роки тому
Well, I think you’d also want to know the thickness too then! 1280g per m2 at 1mm thickness (or 1280kg/m3)
@dontaskme9047 3 роки тому
That depends on the specific gravity of where it is being measured. It will weigh more on earth than on mars. Hope that helps.
@ywen2174 3 роки тому
That changes depends on the amount of epoxy
@adammtroutman 2 роки тому
Depends on the fiber, fabric construction, resin content percentage
@ajhartmanaero 4 роки тому
Nice video as always. When I did some tubes for my car I wrapped some extra tows around the ends to make beads, kinda like your step to pull it off if necessary. This way theres much less chance of a coupler popping off. My application was for car intake tubes that see boost pressure.
@easycompositestv 4 роки тому
Yep, nice tip and nice way to get a small, neat step on the end of your tubes. Totally makes sense.
@swealer 4 роки тому
Hey Man, I was exactly thinking about to make Boostpipes for my Hillclimb Porsche 944. It runs in Racemod nearly 4 Bar (something around 58psi). Son now my maybe dumb questions: Can they handle that? I mean it is mechanically strong of course, but air pressure? would really appreciate your answer. Stay safe out there!
@kayboku7281 Рік тому
ahhhh so thats how those tubes are made! cheers!
@lowe1988 4 роки тому
Seeing that fresh carbon fiber break just hurt my feelings
@one10RC 4 роки тому
It got me excited about how strong this material can be. haha
@lowe1988 4 роки тому
@@one10RC That too lol
@cluelessbeekeeping1322 3 роки тому
Totally!
@danieln1813 4 роки тому
How does this “homemade” tube compare to its off-the-shelf counterpart in terms of tolerances and resistance? (I'm talking about a tube with the same layup configuration and diameters)
@easycompositestv 4 роки тому
Pretty similar Daniel because - although this is 'home made' as you say, the materials and manufacturing process are actually so similar. Maybe if we get chance we'll compare a tube made in this exact way with a matching tube from our stock range and put them both on the test machine. I'll wager that they'll be within a few percent.
@danieln1813 4 роки тому
@@easycompositestv Thank you for your answer! That would definitely make an interesting video
@MM-24 4 роки тому
@@easycompositestv And what about price performance. Equipment non-considered, should we expect a price benefit for building tubes vs purchase? Or is it added flexibility in design? ... or both? Where are these tubes strongest? In the video we tested the tube horizontally, is the tube inappropriate for a vertical application?
@sinegra30 4 роки тому
That is clearly not homemade
@deckmonkey1459 3 роки тому
@@MM-24 China is always cheaper but the tolerances are usually terrible. You can get a free oven from Craigslist that works just as well as the fancy one he has. All you need to do is get it to temperature and have room to get in the oven. Anyone ,including kids, can make this by watching the video. The tube is the strongest the same way as any tube. Obviously, long thin things are always stronger vertically. There's no reason to not buy it other than pride in making it yourself. You are either a builder or you're not.
@mguarin912 4 роки тому
Incredible videos as always!!
@easycompositestv 4 роки тому
Glad you like them!
@In.experto.simracing 4 роки тому
I am addict to this videos! AHAH , respects from Uruguay
@easycompositestv 4 роки тому
Thank you Pablo, great to know we're reaching far and wide.
@alaskanalain 3 роки тому
His hair stands up at the back exactly like mine
@aleksanderscernjavic9009 2 роки тому
For the stress tests I would recommend converting it also into Momentum, since it is quite some difference putting 700kg on a 0.30m long tube or a 1m tube or check if it sustains the same if converted to momentum, which will be more accurate :)
@easycompositestv 2 роки тому
The test was purely for demonstration purposes rather than a precise test.
@user-xy6jh3md2p 4 роки тому
These are the best educational videos! 🔥🔥🔥👍
@easycompositestv 4 роки тому
Thank you, it's great that you think so!
@PablOFW Рік тому
Thanks for this helpful video.
@easycompositestv Рік тому
Glad you enjoyed Pablo!
@rodolfobarros7628 3 роки тому
Except the oven step, the rest is the same process of making a joint!
@alaskanalain 3 роки тому
You made me fall off my chair. Bravo
@Smokeyr67 3 роки тому
Well, one gets baked, the other does the baking...
@MatanuskaHIGH 3 роки тому
Happy 420!
@genkidama7385 3 роки тому
me watching the skinny tube : why the hell would someone want carbon fiber tubes, looks ridiculously feeble, 10seconds later the guy steps on, no deformation, not even one millimeter, put on the press, 600kg required to break it, not even a directional reinforcement was used. wow jaws dropped. now i believe in carbon fiber.
@VinothKumar-qo7ry 3 роки тому
Thanks a lot for sharing knowledge. Huge respect for you..
@easycompositestv 3 роки тому
That's what we love to do.
@Stellarffxi Рік тому
These vids are always incredible. You make it look so darn easy... lol. Though some of the processes I have been able to reproduce!
@easycompositestv Рік тому
Hi Cory! Glad you enjoy the video, with practice you'll certainly be able to reproduce most of the processes :)
@jonjonsson6323 3 роки тому
The interesting thing is not so much carbon fiber wich is strong, but the alternatives. Glass fiber, sandwich with carbon and glass fiber etc. For hobbyists this mean you can make things strong, if you have poor economy by mixing materials
@jj4791 2 роки тому
There is a benefit of using glass instead of carbon in certain tension applications where a little flex or shock absorbsion is desirable. Even carbon fiber aircraft such as sailplanes often use special high strength fiberglass in the wing spars instead of carbon.
@bobdobalina1419 Рік тому
I would like to explore laminating carbon with more abrasion resistant fibers such as aramid and uhdpe
@fabioferraz2835 Рік тому
how many layers of carbon fabric were in this tube?
@ahmedaiman4687 3 роки тому
I have no idea what's going on nor how I could find this useful. But hmmm... Interesting video yes
@chriscarter2101 4 роки тому
Great tutorial. Thank you.
@easycompositestv 4 роки тому
Thanks Chris, glad you enjoyed it!
@MegaCountach 4 роки тому
Excellent video, thanks!
@easycompositestv 4 роки тому
Thank you, glad you liked it.
@nisterror 4 роки тому
@9:14 it has officially been "Defromed" lol
@AndyFromm 3 роки тому
I need some carbon shovel & broom handles...
@tomcoryell 3 роки тому
Expensive Handles!
@Alrukitaf 7 місяців тому
Excellent vid. Just wondering how the test load rig would work out for an aluminium tube though.
@easycompositestv 7 місяців тому
In some ways aluminium and carbon can be compared in some properties so it may well be possible to conduct a similar test with aluminium tubing within the limits of the machines capability.
@jeanfrancoispoivre4438 4 роки тому
Merci à vous pour cette magnifique vidéo
@easycompositestv 4 роки тому
C'est notre plaisir, merci d'avoir regardé Jean
@grendelum 3 роки тому
made a world of difference when i switched to a carbon fiber cane...
@conniestevenson226 3 роки тому
Im thinking about making a walking/hiking stick. What diameter is yours and what length
@grendelum 3 роки тому
@@conniestevenson226 - i didn’t make mine, got it from a company called carbon canes... it’s 3/4” diameter and cane length? like 3’ or so... has flames coming up from the bottom ;¬)
@conniestevenson226 3 роки тому
@@grendelum sounds awesome looking. I would think 5 feet would be perfect for what i need. Im looking to use a 28mm kevlar carbon hybrid shaft
@emirdkl 4 роки тому
I wish i can handle that amount of stress too :/
@genelomas332 3 роки тому
Don't underestimate yourself, you're a carbon based lifeform.. you'll get through it.. 👍😁
@olehoiii 4 роки тому
Great video as usual!
@easycompositestv 4 роки тому
Thank you, we appreciate it.
@richardlab8858 4 роки тому
Always great videos thank you :) I wish also a video for how to make a bladder!!
@easycompositestv 4 роки тому
That's certainly a video we'll be making in the future Richard.
@GoEvenHarder 3 роки тому
I legit dunno why this is on my recommendation
@0x80O0oOverfl0w 6 місяців тому
If only people who were interested in submarines saw this video.
@joshuabailey1825 2 роки тому
I will probably never make anything from carbon fiber yet I watch video after video from you guys. Love from Texas.
@easycompositestv 2 роки тому
Hi Joshua, thank you for your comment! Glad you enjoy our content, we've got plenty of new videos in the pipeline that will be uploaded soon
@ispalin4667 3 роки тому
Top work👍👍
@rs4race 4 роки тому
When I saw stress in kg.... 🙈 damn cant un see
@nisterror 4 роки тому
Lol
@chrisk1258 4 роки тому
Actually the machine outputs the force it applies versus the displacement of the head (deflection in this case). So kg is fine. The internal stresses can be estimated by considering the dimensions of the tube and the external load applied.
@ayhamibrahim6622 4 роки тому
Super professional human ❤️
@easycompositestv 4 роки тому
Haha, thank you very much!
@emanuelgoncalvessantos4499 2 роки тому
Subscribed, you guys have some serious tubing there!
@easycompositestv 2 роки тому
Thanks for subscribing!
@crispy-k 4 роки тому
Interesting vid !
@alwayslookonthelightsideof2268 9 місяців тому
Great video thanks learnt alot. Excellent to be learning. made me think of golf clubs - - just needs to be tapered. guess that wouldn't be wrapped in such case.
@easycompositestv 9 місяців тому
You could make a tapered tube by a similar method.
@alwayslookonthelightsideof2268 9 місяців тому
@@easycompositestv thanks :)
@remkojerphanion4686 4 роки тому
Love these video's!
@easycompositestv 4 роки тому
Thanks Remko, we love making them.
@khalidrao4716 4 роки тому
Its really a useful and informative video. Thanks
@easycompositestv 4 роки тому
Thank you Khalid
@mgomes32 4 роки тому
Great video! Thanks for sharing it
@easycompositestv 4 роки тому
You're welcome Marco, thanks for watching!
@markmark5269 2 роки тому
Nice video, well explained without big egos for a change. If worst comes to worst, remember that common swimming pool acid will dissolve the aluminium tube away in a minute without affecting the CF at all. A professional fiberglass friend who makes fiberglass tubes, uses cardboard tubes, then just throws them in water overnight.
@easycompositestv 2 роки тому
Interesting comment Mark; it wouldn’t be possible to use cardboard as a mandrel for a prepreg tube like this of course (the process relies on thermal expansion of the mandrel) but it’s a novel way of making a mastic fibreglass tube.
@the-senior-tech 3 роки тому
Great video.
@michalisrx7 4 роки тому
perfect!!! material
@inventgroupPL 2 роки тому
Great Video!
@easycompositestv 2 роки тому
Glad you enjoyed!
@Joelmelanie 3 роки тому
Great videos
@CameronCarter1 4 роки тому
Excellent stuff, Thanks.
@easycompositestv 4 роки тому
Thanks Cameron, glad you enjoyed it
@mattiasandersson3444 4 роки тому
Wow, that is Amazing !
@easycompositestv 4 роки тому
Thank you Mattias, Cheers!
@amirfathirad2965 4 роки тому
please make more videos I really love to see your videos and learned so much from it please if it is possible for you to explain more about homemade composite planes and technics got get used in it also please if it is possible thank you so so much for all the information you shared so far you are the best
@easycompositestv 4 роки тому
Thanks Amir, yes, we plan to do some tutorials on advanced constructions for aero-modelling/fixed wing UAV etc. Hopefully these will include some of what you're looking for.
@amirfathirad2965 4 роки тому
@@easycompositestv thank you so much you are the best
@Frey_64 4 роки тому
this is so CooL , keep making videos !
@easycompositestv 4 роки тому
Thanks Freddy, we will.
@chuckeynewkirk199 4 роки тому
Great video amazing technology and what it can do for you thanks thanks a lot
@easycompositestv 4 роки тому
Our pleasure, glad you like it!
@paulinadeluca9117 4 роки тому
The best teacher
@easycompositestv 4 роки тому
Thanks Paulina, that's very kind.
@Happy_2_Wheels 4 роки тому
Nice video!
@easycompositestv 4 роки тому
Thanks Doni, glad you enjoyed it
@NewLiftWalker 4 роки тому
Fantastic!!!
@easycompositestv 4 роки тому
Thank you, glad you enjoyed it.
@carlosalbertovelascoquirog9957 2 роки тому
Excelente explicación amigos 🐱
@easycompositestv 2 роки тому
Thanks Carlos!
@maxsam201 4 роки тому
Really awesome 👍
@easycompositestv 4 роки тому
Thanks a lot 😊
@liammiller9296 4 роки тому
awesome video. Subscribed !
@easycompositestv 4 роки тому
Thanks for the sub Liam!
@enso3140 3 роки тому
can this process be used to create straight trumpets (with some draft angle)? and is it only usable for fully round parts?
@mustafacakir534 2 роки тому
wow great a metarial. Thank you
@easycompositestv 2 роки тому
Thanks for your kind comment!
@c2rautomotive 4 роки тому
amaizing videos!
@easycompositestv 4 роки тому
Thank you, glad you like them.
@standardannonymousguy 4 роки тому
How would you make a curved tube for cruiser style bicycle handbars? I've been riding on a carbon fiber road bicycle for a few years now and have been very impressed with it's lightweight quality and durability. Thank you for sharing!
@easycompositestv 4 роки тому
Hi Lucas, that's the very next video we're doing. For curved tubes, like handlebars, you need a split-mould process. New video in around 1 week; subscribe and hit that bell.
Easy Composites Ltd
Переглядів 1,8 млн
Matthieu Libeert
Переглядів 504 тис.
Бомбардир
Переглядів 430 тис.
Tips Workshop
Переглядів 54 млн
ECO-LAP Studio
Переглядів 2,1 млн
Easy Composites Ltd
Переглядів 296 тис.
Hawthorn Composites
Переглядів 144 тис.
ECO-LAP Studio
Переглядів 730 тис.
Всячина Games
Переглядів 2,5 млн