I have done it, here are two important tips : drill holes before you cut the casing. Make sure to put alot of silicone and that the holes are outside of the silicone. Really put alot, even if you get access silicone dripping out.

I think the plastics used in drum tubs are typically polyolefins like polypropylene and PET, which are plastics that most stuff including silicone doesn't adhere well to, although you can buy adhesives designed to bond polyolefins, or a polyolefin primer which modifies the surface to allow other stuff to stick. Don't use a primer + superglue combination as cyanoacrylate is not water resistant. The type of plastic should be marked on the tub to aid recycling.

You can use the old bearing to drive in the new one and clean the shaft a little with emery cloth before inserting 👍🏻

Thank you for your video , i have the same whirlpool outer tub and they seal together, they try to make it so no one to fix it... MAY i ask how is it after couple months using it??? Did you take out cover or look underneath see if it leak??? I would like to cut off and fix my too.. thanks

Thank you for the video

clean the inside drum halves while its apart?

Anyone completed this repair on a beko tub?... Tried to order bearings first but a good supplier said they are not listed with 4 of there suppliers. Thanks

Were both bearings 6204? Also seal size please. Thanks and good video.

Clean the drum and casing first, spindle too, spotless they need to be, to drive the bearing in use a 12mm bolt and big penny washers to clamp them and squeeze into the hole no hammer needed, and to pull the spindle through again washers and a socket plus bolt don't risk cracking the casing, the seal is better if you use a PU seal like tiger seal.

Not sure that I would like to attempt this and I do like to fix stuff.The sound / vocals at around 15:20 make the whole thing worth watching

Thanks G

I think you can fit bearings with hard wood block instead of using hammer directly.

really helpful video - going to try this myself - any hints on which bearings will work please? All the suppliers just keep saying they can't be replaced. thanks, Julian

After watching this saga.. After the first screw the whole lot would have gone straight to the dump .. Clothes in it included 😀

You're hoping the thin silicone seal will tolerate the spin and heat cycles without leaking, never mind potential air leaks to interfere with the pressure switch and drum filling. I would not feel comfortable leaving this repaired washing machine alone while I'm out. Would it not be possible to plastic-weld the drum closed again, at least the seal would be durable?

I have the same tub, can you tell me what size bearings you used to replace, cheers

🎉

How many holes did you drill? I am opening my sealed drum only to clean the shit out of it. Thanks for the video

Where do you get the bearings when only the total drum kit is available?

Hola cómo pasaron unos años hoy sigue funcionando la lavadora gracias

silicone leaked :( time to buy a new one

Why do they make it so hard?

Diciamo che il lavoro potrebbe essere fatto meglio di così. esempio la guarnizione oblò non era necessario rimuoverla dalla vasca. Il taglio della vasca e impossibile farlo con la sega vista nel video ma con un frullino con disco in metallo per mattoni. Gli ammortizzatori potevano essere rimossi da sotto la lavatrice togliendo il dado. Le viti erano troppo distanti le une dalle altre.

What glue are you useing ?

Hi! Firstly, very good!!!..👍🏻 But I would like to ask you... For a job of this kind, which to me seems anything but simple and fast, therefore including labor and part/spare parts, done by a specialized Multi-brand technician, (and therefore by a professional, and not by an impromptu under the stairs of his house... ) how much would it cost today 2023??...... Because in my opinion it is better to get a new bath group.... Or am I wrong???... Also because, in any case, opening it and redoing everything would nevertheless be something "botched," with possible errors (because it can happen...) in the work of the technician himself, which the customer would never find out about, and therefore not actually comparable with a completely brand new bath group, and therefore from the factory, made with computerized numerically controlled machines. Also because, moreover, we must take into consideration the fact that if, for example, the bearing needs to be changed, it must in any case be said that the cruise (which is perhaps still "healthy"... ) has in any case made its working life, and therefore it could break (as happens many times) shortly thereafter, and therefore what to do?....Reassemble the whole washing machine again, extract the whole tub group, and reopen the latter again, to weld the cross, or replace the drum (basket) with a new one, and insert it on an old, messy tub?..... Which by the way, being this in any case in porous plastic, although previously cleaned, is in any case aged, and ruined!.... Personally it seems to me something truly anomalous, if not silly, and therefore incomprehensible, but above all I believe that it is not convenient under any aspect, (cheap in the first place..) form, and place. On the other hand, perhaps a different thing could be for a tub that is still in plastic, but one that can be opened from the factory, even if it must be said that even for these that can be opened, the problem of aged plastic, and ruined by time and prolonged use, would not be solved . Completely different situation, possibly for steel tanks, which are "eternal" and easy to clean and therefore "eternally new." what do you say...... I wait for you.... Bye thank you!

Use tiger seal

97 b

Never use only liquid detergent and low temperatures!