In this lesson of our Guitar Soldering Course, Besty shows you how to master soldering to guitar pots. See our handwound guitar pickups: www.radioshoppickups.com/
КОМЕНТАРІ: 55
@thebreakfastmenu3 місяці тому
Man, folks like you that have free tutorials like this are MVPs, big time.
@quintijn3444Рік тому
Just a little headsup for the people who aren't working with CTS pots but cheaper alternatives. They're often a bit more tricky to work with and need cleaning before you use them. Otherwise you run into situations where the tin won't stick to the back of the pot. You can read about people sanding the backs with sandpaper, but I find just cleaning them with an alcohol or naptha works great and makes them just as easy to work with as CTS pots!
@notanotherguitarchannelРік тому
Thanks! Yeah I was having a hell of a time with some cheap pots that had been sitting in my shed for a couple years.
@ibanezsr505latin11 місяців тому
Im gonna be working with a smaller version of a Volume pot i picked up from a local guitar shop... potentiometer is smaller but states that it will work we will see
@Phillip_higginsМісяць тому
Thanks
@downtownbillyandthenewjivefive19 днів тому
@@notanotherguitarchannel If they were sitting in your shed, they oxidized.
@freelance_commieРік тому
Wow, can’t wait to be able to rewire my couple of guitars. Such smooth and clear instruction, thanks!
@AdADglgmutShevanel8 місяців тому
Very cool! This close up really helped me understand what is going on when you solder!
@Ozzy3333333Рік тому
Back in 1992 to 1997 I had a roommate that played bass and repaired guitars, mostly re-frett'ed the necks, he started complaining about the shitty pots/switches/jacks that even expensive guitars use. At this point I have had decade plus repairing computers to component level, and everything else I owned. I easily knew how to solve his shitty component problem (like the rubbish pot your soldering too). Bourns or spectrol pots are some of the best out there, the cermet have 1 to 5 million rotation life, yes, I said million. Cutler/Hammer are some of the top toggle switches. He ended up replacing all his and liked them so much, he sold kits of these parts, about 230 kits per year until I moved out and bought a house. The cable jack was special, ball bearings and was a work of art. He started making high end bass guitars for a while, not sure what he does now.
@giulioluzzardi763211 місяців тому
Thank you guys, needed to see how you solder, lots of light and magnifier(some-times) help too...and the obligatory calm disposition! Thanks again.
@moose66764 місяці тому
Thanks for a really great video, this has given me confidence to start doing my own work instead of paying. 🙏🏻👍🏻👍🏻
@JamesTodinoРік тому
Thank you mate! Always struggled with getting a neat ground blob on the bottom of a pot, so I've been in need of advice like this!
@ruzcelbeltran5 місяців тому
Amazing tutorial clean job
@anthonybraun2665Місяць тому
Thanks bro, you're a WINNER!! 😄
@simonmcc3608Рік тому
A fantastic video! I like the look of that wee vice for holding the components. Stops you from chasing it around the table!! Where would I get one of those?
@elchivojotaРік тому
Interesting approach to the terminal soldering! I was always taught to do the 'curl"' method for the wire through the lug, to ensure the two entities have adequate contact prior to closing the joint. Thoughts on that?
@ibanezsr505latin11 місяців тому
Your are an expert best video by far
@mikemanne811211 місяців тому
very nice
@megadawg342Рік тому
Great technique. Thanks for the lesson.
@brunom34787 місяців тому
What's the wattage on your soldering iron?
@FF-so3suРік тому
Thanks
@dfanman17 місяців тому
You make this look so ridiculously easy. Me and soldering do not get along at all. I'm the type of person who can't get that solder to stick to anything no matter what I do. It's maddening!
@user-sj3sx3rq7h6 місяців тому
im in the same boat, it has to have something to do with the tinning and cleaning, maybe im not using enough tin or the wrong solder
@das.ruderboot5 місяців тому
I highly recommend solder that still got lead in it! also it needs a flux core! Flux is extremely important, makes the solder flow and not stick. You can also get flux in a tube, put some where you want to solder and it'll flow easily. I started off with lead free solder and no flux core, and it was horrible. Getting some good lead solder with a flux core allowed me to create shiny and perfect solder joints. The solder just flows like no tomorrow
@JacobR.8810 місяців тому
What temperature do you use while soldering the back of the pots?
@sergioalejandrosaenzperez516310 місяців тому
a query, what type of soldering iron and tin do I need to do this electronics job?
@mknewlan678 місяців тому
My 1st time soldering and using cts pots I can’t get the solder on the pot. It either sticks to the iron or the solder itself. Any suggestions? Please?
@pablopicasso73438 місяців тому
Make shure your soldering iron is hot enough. You need bigger soldering tip and more heat than for electronics.
@mknewlan677 місяців тому
@@pablopicasso7343 found out I was using the wrong solder. Works like a charm when using proper gear lol.
@Ozzy3333333Рік тому
Another trick my roomate did to the guitar necks, instead of varnish, he used thin CA, many coats with light sanding/cleaning in-between, this made the finish bulletproof from sweat/etc.
@saintbodhisatvaРік тому
what is thin CA... sorry Im not from the USA
@Ozzy3333333Рік тому
@@saintbodhisatva super glue, in this case the ultra thin stuff
@LeonRHarvey3 місяці тому
these are better than the Seymour Duncan lessons ;D
@frcktest9995 місяців тому
Hi What kind of wire you use please? I bought a silver but cant connect to pots 😅
@buttholesniffersРік тому
What kind of wire do I solder to the pots? Not talking about the solder itself but the wire that will be soldered
@christophercolumbus894411 місяців тому
leg or lug ?
@fleetwooddave10 місяців тому
Help me wrap my head around why the 3rd lug is bent in to ground and if there is a circumstance where you wouldn't go to ground with it but use it for a different objective...thanks
@danielbermudez15529 місяців тому
The 3rd lug is the end of the resistance in a pot, if you put it to ground you're looping the circuit and making it go silent, that's why it's main use is in the volume pot
@ytmndan4 місяці тому
Why not solder the ground wire through the grounded lug?
@user-gu9pk9kb9e10 місяців тому
What temp is best to set the solder gun at for jobs like this. 800-900 lol just kidding but this knucklehead has no idea. Appreciate any answer or help
@6strings1pickup124 місяці тому
Is there a reason you didn't just solder the black wire to the pool you already created when you soldered the lug to the housing? I'm a soldering noob lol, just started.
@jnicholls213 місяці тому
The soldering of the wire already soldered is likely to be compromised if you re-flow the pool to add an additional wire.
@SionynJonesРік тому
Da iawn. Thought I detected a bit of Welsh accent. So cool to have pickups made in Wales.
@RadioshopPickupsРік тому
Diolch Sionyn! Inni yng Ngorllewin Cymru (Gogledd Sir Benfro) dyddie hyn :) Besty
@christophercolumbus894411 місяців тому
@@RadioshopPickups why do they always solder the last leg to the potentiometer ?
@97warlock4 дні тому
Wih My solder would melt that fast. I have to hold it to it like8 seconds till it begins to melt it then it melts it fast, then start again & wait & wait & wait, till finally it will start t o melt. i have a 35w but its Old now
@donkink3114Рік тому
Strip wires 3/4 inch(19mm) tin them Tin the lugs on the pot. Wrap wire thru the lug while heating it Twist tight then solder a bit more.for a fairly durable physical connection as well as electrical. Use heat shrink tubing to weatherize the connection
@fearnpol4938Рік тому
That’s a ridiculously unnecessarily long joint, the insulation should only be cut back circa 1/4” 5mm at max for this joint. Re twisting of the wire should never be redone as you end up deforming the wire. A correctly made hook joint will have more than enough mechanical strength for anything this joint would be likely to have to face.
@jewblin53055 місяців тому
Soldering is the pain in the ass of my guitar life. I hate doing it and always get clumsy results…
@flukyreview91287 місяців тому
Tinning the lug is not necessary. Just tin the wire then insert it through the lug hole and solder using small amount of solder as you heat and make contact with both wire and lug. Hmmm your soldering will not pass Mil Specs mate. 🤣🤣🤣
@fearnpol4938Рік тому
The tinned wire looks to have too much solder on it as it looks stiff beyond the insulation, this is bad as it doesn’t allow and easy bend to create a joint, the wire should have no solder inside the insulation and should stop circa the dia’ of the wire before the insulation starts. Also the tag has too much solder on it as the hole should never be filled in.
@curtrod7 місяців тому
nah
@sidneyolson8795Рік тому
ᎮᏒᎧᎷᎧᏕᎷ 😱
@marshallohio5512Рік тому
OMG, stop scratching/sanding guitar control pots before soldering !!! Unnecessary !!