A little tip so that you don’t need a reference for the dots on a die. The opposite sides all add up to seven. 1 is opposite 6. 2 is opposite 5, and 3 is opposite 4.

ok, but what is to the left of 1. or right. underneath.

قمة الدقة و الإتقان ، تحية كبيرة لك من المملكة المغربية.

@@Dirk_Mcgurk Well underneath 1 is 6. The other four sides are 3&4, 2&5. It doesn’t really matter which sides you put them on because the die’s weight will be balanced, and it can face any direction. So if you turn it 90 degrees a different face will be on the left.

Надеюсь сталь нержавеющая. I hope the steel is stainless.

Haha, they’d throw sparks while playing 😅

Thank you so much, I really appreciate! 🙂

RIGHT?!!!

@@andrewhooper5645woah 4 seconds ago

He might sCrAtCh it

It's 4 ounces, @worldscoolestusernam! It's more like a paperweight at this point!

It won’t roll even, it’s not balanced like normal dice. Just a beautiful,desk piece :)

Thank you so much! I started with 0 experience, learning by doing :-)

Challenge accepted 🙂

Thanks!

Thanks a lot! Iam glad you enjoyed 🙂

Ultra-fair would be a good idea. But it doesn't HAVE to be transparent. Black or red would look good, too!

I will, when I make the d20 dice 😅

Another suggestion would be to pre-drill 4mm thick brass disk blanks with your hole patterns for 1-6. The pre-drilled side of these disks will then be the side that gets pressed into the steel block so the dimples are hidden (it will be an idea to mark them on the blank side so you know which is which). Once you have them all pressed into place drill the 6 side with 1 dimple, the 5 side with 2 dimples, 4 side with 3 dimples and so on. That way each brass disk will have the same 7 dimple's worth of mass removed. A 3mm drill, sharpened at 118° has a tip depth of around 0.9mm, if the dimples are drilled to 1mm that gives 0.1mm for polishing the sides to a high sheen without leaving a step. Hope that makes as much sense to everyone as it does in my head 😂

@@Galerak1 Thats a great idea, even better than filling the dimples with brass-weighting transparent material.

Or not transparent... Filling them with solder would make them silver...?

Thank you so much! I really appreciate the feedback of an expert 🙂

i dont think ive ever heard exquisite and bro in the same sentence before lmfao

You’re welcome!

Thanks!

Thanks!

Thanks!

Thank you so much!

Thank you so much!

Thank you so much!

Thanks for watching! 🙂

Thanks!

Thanks!

Merci! Je suis content que tu l'aimes :-)

Thanks! Iam glad you like it! 👍

Thanks! Iam glad you enjoyed!

What a nice idea! 🫢

I was going to suggust inserting copper or steel into the divits before drilling. But this is also cool!

Thanks!

Thanks! 🙂

Thanks!

Thank you so much!

Thanks Vince! :-)

Thanks!

Spasibo!

Thanks!

Funny, right in the moment iam searching for inspiration/images of a d20 😅

Spasibo!

Thanks!

Или сталь

Respect is the thing 👌

Thanks Kate!

Thanks a lot!

Thanks!

Thanks!

Thanks! 😅

Thanks!

Thanks a lot my bronaldo ❤️

spasibo!

Thanks!

Thanks!

Thank you so much, glad you enjoyed!

Thanks!

Thanks!

Hey Jerry, thank you so much!

You're so welcome!

You're so welcome

Grazie :-)

Thank you so much!

Спасибо брат! Я желаю тебе всего хорошего!

Обнял@@misterpatina

Thanks!