I Turn One Cylinder Engine Into Radial Engine (part 2): ukposts.info/have/v-deo/hIOGl61-i4KZpaM.html

Interesting project. Will be really cool to see it run. I’d recommend getting some collets or end mill holders instead of using a drill chuck for milling since drill chucks aren’t designed for the sideways forces of milling. You can easily damage the chuck, or even have the chuck fall off the arbor. You’ll also likely see a better cut quality with this change from increased rigidity. Good luck finishing the engine!

Three-cylinder radial engine? Buddy, you are a real engineer! Thank you for another awesome video! I wish you success in your work and lots of new ideas!

We call this people. A person with golden hands .

One of those Honda motors had a high compression big bore piston for sure And I’m sitting here say what is he making now then I see it done and I’m like this dude is a mad scientist

Yay I'm glad you are attempting this project. Maybe for lubrication you could use a oil fogging nozzle for the cylinders. The biggest problem with radials is the oil leaking into the bottom cylinders and hydro locking, it usually destroys the rods.

Excellent work, I made a radial engine a bit larger with 5 cylinders, similar designed *bobbin* style master rod. To balance the engine, I used the total of the rotating weights and just over half (0.508) of the reciprocating weights and worked well. Because of the geometer during rotation, you may find the top dead center positions are not equally spaced,, mine are several degrees different and I set ignition timing individually for each cylinder and also cam timing. Because of this anomaly, balancing is a compromise. To speed up the build I used a car exterior 12 volt fuel pump running on 24 volts to pump the engine oil and works very well. I used a cheap fuel pressure regulator to maintain 30 psi oil pressure to crankshaft and the cams and the spill off sprays into the crankcase to lube the pistons and rods. I pull a lever and lift the inlet valves (not the exhaust valves)to drain the 2 lower pots through a ball valve at lowest point of inlet manifolds (i have 5 carbs) . I turn the engine over by hand twice before starting to prevent hydraulic lock. Radials are an amazing, slightly different engine, feel free to message me, glad to help if I can.

I love watching smart people work. Looking forward to seeing this thing run.

You're an absolute genius when it comes to this work and I love it! We can all learn some things from you.

You're a BadMoFo! My hat is off to You Sir! I could watch You all day!

To say you're a genius is an understatement.

I was so engrossed in the video that I didn't realize it was about to end. I was SO bummed! Can't wait to see part 2!

A radial engine, that's a new one for ya. Very good work my friend

you're a real mechanic bro

Thanks for coming out with a new engine building video! I love these.

I love the design of 3 cylinder radials. They're very rare.

Holy crap, the man even made friggin oil channels. I’m working on designing a 2L 120 degree v8, and from that, I know that making those by hand is is an incredible feat of skill and engineering. Nice work!

This guy does a great job. It’s all real design problems with real solutions. None of this “life hack” shit

My god, what a build! Don't keep us hanging man, lets see it run!!

I'm from Indonesia, I like content about making machines. Success is always 🥰

We're excited to see this run! Great work!

This is really amazing.... Can't wait to see the completed engine.. ❤️❤️❤️❤️

This is exactly the kind of thing I want to start doing

I'm always waiting videos about engine in this channel,thankyou sir you make this for us

You make it look so easy mate, good job 👍👍👍

Always AMAZED by your skills. 👍🙂👍

You Sir are a true Craftsman with an Amazing talent. I’m a subscriber now and really looking forward to the other videos and the future ones too. Makes my day Hoss 🏆

Maybe one day you will make a Boxer engine with pistons directed towards each other, that is a real boxer engine . Great work, comrade!

Absolutely outstanding engineering and video recording. Welding looks like some sci-fi footage. Side of grinding wheel to flaten crankcase great. Simple construction is best. Live long and prosper!. Dave

I was not able to finish this nice video and listening to that background music.

Kangen banget vidio dari lets learn someting, salam dari indonesia🇲🇨🇲🇨

Nice work 👍. I'm curious to see how you are going to run the cam chain. Keep the videos coming

Koleś jesteś mistrzem,podziwiam

Хорошая работа друг, люблю такого рода инженерию с кабовскими моторами, фантазия с ними при наличии рук, и инструментов бесконечна))

I'm waiting for part 2

Irmaozinho você e muito talentoso , magnífico , vamos esperar o resultado final , mas até agora está legal , muito bom , parabéns

👍С нетерпением буду ждать продолжения, успехов в дальнейшей работе.👍👍

ganda nyan bro, nakakabitin!

Almost there. You still have to devise a cam mechanism for the valves and distributor. So far, excelent job. 👍

👍 much respect for your ingenuity!

Скоро так дойдёт до авиационных 7-9 цилиндровых 🤔🤔🤔. Он 100% их создаст

AMAZING SO FAR....THANKS 🇺🇸

Świetna jest ta zrobiona robota pozdrawiam twórcę tego filmiku 👍👍👍👍

Radial engine its so hard! Good work

Amazing Project!

Millyard would be proud of you, then he narrates and explain while machining.

Please part 2!!! Amazing work

I can’t wait to see this in a bike great job

The skill and ability of some people really knocks me out. I'd have loved to do things like this, but I'm not technically minded. Thankfully, my son is, and we're creating a little go-cart for my granddaughters. My boy said I could pump up the tyres....so that's something to look forward too! 🤣🤔🥺😫😡 Extraordinary vid. Can't wait to see part 2 and see that badboy in action👍🏻👍🏻

Thank you for sharing 💕❤️💗🥰🥰🥰

Гениальная идея. Потрясающие изобретения.

Just started watching it but I already know I'm gonna enjoy this video just as much as all your other videos. Thanks for the great content man!

Is it safe to say. That this guy is a mechanical genius.

Another awesome video mate! Can't wait to see the finished result. It's been great to see your skills and techniques develop, as you've taken on harder and harder projects over time. You are truely inspiring and you produce videos that always entertain and keep me wanting more. 😊

Huge project.thanks

Nice tools and workshop awesome

Can't Wait to See Part 2 😁👍

Nice bearing tools!. 🤤😁

It's amazing engineering .,,

dang dude you killed that

I wonder if the master rod could take more than 2 horses😲. Never ever weld any rotating engine parts. Good work though. Keep'em coming

You sir are a madman

holy hell im half way through this video and i think i need eye protection to continue

Its really impressive 👍

So, it’s time to make an aircraft with this engine!😂

Огонь. Чекаємо продовження

круть! вот бы ещё картер из алюминиевого сплава сделать вместо стали. 👍✌

Ngeri wong iki🔥

zarpado perro !!! saludos de Argentina!

Wow this is so cool 😲🤘🏽🔥

😯 wow, this guy is amazing 👍😯

i like these custom projects

Start your taps by hand in the drill press so your threads come out more straight but nice job so cool

Ang galing.🇵🇭

Awesome work!👍😁⚒️🛠️

beautiful engine

BRAVO!!!

For the amount of eye balling that's going on here, it's truly amazing what he can accomplish. Will it work, idk.

Dude! You're freakin' amazing.

Лайк за сварку и экономию металла.

Id really like to see you do this with small diesel engines

Very interesting 👍

Where do you get the metal sheets from?

What a great video, but please please, find some less repetitive music.. Thanks 👍👌🍺

Keep up the good work that is so cool and a good idea 😁😁😁😁

Great video! Great work!🛠️🔧😁😀

Interesting project

make a 2 stroke engine with camshaft and valves

lupit ...part 2

I wish I had 1/3 of this guys smarts

good job bro👏

Awesome beautiful.

Thank you sir 🙏

Show de bola amigo parabéns

Просто шикарное видео.Лайк однозначно.

I’m not sure it is fair to say you turned one thing into another. I think you pretty much built something from damn bear scratch. Wonderful UKposts.

Muito interessante seus vídeos 👏👏

Ожидаю продолжения !!!! Кулл ! )))

10:22 do you look at the machine line and sometimes think your settings are off? That's what always got me, I doubt myself too much as a teenager.

Ansioso para ver funcionando.