3D Software For iCubeSmart 3D8S, 3D8P. We regularly publish videos about 3D software operations and videos from 3D animation productions.
КОМЕНТАРІ: 57
@softwaresolidarity19014 роки тому
Is there any way to get technical info about the device/interface? I'm a programmer and would like to write a linux driver / program that interfaces with this cube.
@ranbymonkeys23843 роки тому
Did they ever get back to you on that or come up with a way to use Linux?
@petermead75102 роки тому
Ditto RanByMonkeys question?
@zoltankomar39502 роки тому
The completed program that I can upload to the led cube. The files have the gpro8 extension.
@faustoserone6353 роки тому
Hi, I tried to send the program with stc-isp, but if show the message: " USB-to-RS232 line. It is still in connection state, please supply target MCU power... Please, help me! Thanks
@brandonescobar49552 роки тому
I recently purchased and build it up using the instructions and everything works to end of video! However I an trying to use install the program manual provided on the amazon page and when I plug in the usb adapter with the connections RXD, TXD, and GND made with the ylw compartment to vcc and 3v3 made, the usb device is not showing up on computer management device manager. Any advice?
@bruceholland32Рік тому
It showed up under ports (COM/LPT) in device management screen
@edgarustian39484 роки тому
Is it possible to delete some animations from the cube? I also would like to know how much memory does the cube have so I can know how many animations I can put on it.
@iCubeSmart4 роки тому
Dear friends, there are twenty-five kinds of animations, which account for about 50% of the memory. The complexity of the animation determines the memory it takes up, not a fixed value.
@wolfgangboettcher31262 роки тому
Ich denke nach so jung waren wir Mal
@TYKE-NO3 роки тому
still cant find software. downloaded directx9?
@petermead75102 роки тому
Is there a linux version?
@bigtst362 роки тому
I purchased the kit and assembled in May of this year. Worked fine till last week. Now only bottom LEDs work when powered up. None of the cube LEDs work. Any help would be greatly appreciated.
@joshuanafziger81002 роки тому
Check ALL of your connections...... IDK man, sorry to hear that.
@zanderi2 роки тому
You can follow a similar process of testing the led's like you did when you built it if they light up then it's a matter of tracing the connections and seeing if you have a bad solder connection. We had a couple we had to go in and fix after the fact because the solder wasn't done well.
@bigtst362 роки тому
Already checked led connections and all are soldered and working properly
@djmcroby2 роки тому
Hi, I created my own program but how do I load it into the cube ??
@Windows-pt4nnМісяць тому
Hello, I didn't understand it at first, but you have to go to "Compile" in the editor when you've finished your animation and then just load the "output.hex" in the uploader.
@brightsky24272 роки тому
it works but need a looooot of patience
@berndfron57713 роки тому
how do i get this file into an hex file ? So that i can upload it on my cube
@iCubeSmart3 роки тому
Click on File - Compile
@Marco-td6ii3 роки тому
Will the software work with Windows 10 or 7?
@iCubeSmart3 роки тому
The latest computer has DirectX12 software installed by default. This 3D software is based on DirectX9, so the reason why the 3D software cannot be opened may be that DirectX9 is not installed. The following link is the download address of DirectX9: DirectX9: drive.google.com/open?id=1y1AGc2f6znitlyIzTc-edCSFEoTuwm4_ After you download, unzip and find dxsetup.exe, double-click to install. Then try to open the 3D software.
@PVTuyenРік тому
Can I buy this software?
@wolfgangboettcher3126Рік тому
Das ist der kleine Anfang der DiY
@wolfgangboettcher3126Рік тому
Freunde Super
@smaronboruah3 роки тому
hello, can you make a similar software for 32x32x32 led cube?
@iCubeSmart3 роки тому
Yes,i can
@smaronboruah3 роки тому
@@iCubeSmart please do so if u can, it would be a really big help Not necessarily 32x32x32, any large size would do too 😓😓
@iCubeSmart3 роки тому
@@smaronboruah Software simulation can be done, but led cube welding can't be so big.
@smaronboruah3 роки тому
@@iCubeSmart I was thinking of making something like this as a project 👇 ukposts.info/have/v-deo/nmGKgq-IqJiap2Q.html I can somehow manage the welding, but I'm unable to get a hold of the programming, so if u can make something, it'd be a REALLY big help
@benjamindyson2264 роки тому
im having an issue with uploading a program from my computer to the cube using STC-ISP.exe, keeps coming saying that it cant connect We are trying to connect to target MCU ... Connection is failed. Please try: 1. Click ISP-Programmig button in Power-Down mode, then Power-Up 2. Stop programming, choose another RS-232 port, check the connection line 3. Connect P1.0/P1.1 to ground, then supply target MCU power. 4. Check external clock connection. 5. Update STC-ISP.exe software 6. MCU might not have ISP code inside, or the MCU has been damaged. 7. If using USB-to-RS232 line, it might not be compatible. We can help you buy a compatible USB-to-RS232 line. It is still in connection state, please supply target MCU power... this is the error it shows, what can i do to resolve this?
@iCubeSmart4 роки тому
Dear friends, the steps to download the program are as follows: 1. Connect the three wires of TXD, RXD and GND. The TXD of the downloader is connected to the TXD of the motherboard, the RXD of the downloader is connected to the RXD of the motherboard, and the GND of the downloader is connected to the GND of the motherboard. 5V does not need to be connected. The white DC power cord is also not connected. 2. Select the chip model as STC12C5A60S2. 3. Open the program file you want to download. 4. Click Download / Program. Then use the white DC power cord to connect the 5V power adapter. If it does not start downloading the program, please unplug the DC power cord and plug it in again. The download software is to detect and download the program at the moment when the motherboard is powered on. So you need to power on the motherboard after clicking download / programming. If you still do n’t understand anything after you try, please email me (icubesmart@gmail.com), I will try my best to help you solve any problems you encountered in the DIY.
@daandw49313 місяці тому
how do i run the program i made on the cube?
@iCubeSmart3 місяці тому
You can use 3D software to output the HEX file, and then download the HEX file to the motherboard.
@kand016Рік тому
@Rayan72827Рік тому
Hi, Where can I download premade animations?
@Windows-pt4nnМісяць тому
Hello, I didn't understand it at first, but you have to go to "Compile" in the editor when you've finished your animation and then just load the "output.hex" in the uploader.
@wolfgangboettcher31262 роки тому
Wir machen das locker
@wolfgangboettcher3126Рік тому
Das kommt
@TYKE-NO3 роки тому
need help with software. been trying for 6 months to download and use software. help
@iCubeSmart3 роки тому
Please download the latest zip file package from the following link of Google Drive. drive.google.com/file/d/1a62NuU_QtyUHD0oo4XSAAWj_dZoWQHCB This zip file package contains photos of the high-definition production process, 3D software and software manuals, download software, downloader drivers, and detailed download process documents.
@sanjeevluxman41243 роки тому
Hi can I get the link to download the software its self? Thanks
I bought you rcube on Amazon, where do I download this software?
@iCubeSmart4 роки тому
Dear friend, You can download a zip file package from the following link of Google Drive. drive.google.com/open?id=1YYw6fDU2zbKVlcF7XnJDQR83HCsZ6HyP This file package contains detailed DIY installation instructions, software and download procedures. The following link is a video of the DIY installation instructions. ukposts.info/have/v-deo/bJFkg4OnoZqFz2w.html
@JacklynB4 роки тому
@@iCubeSmart having a hard time getting the software to install, please help
@iCubeSmart4 роки тому
Dear friend, You can download a zip file package from the following link of Google Drive. drive.google.com/open?id=1YYw6fDU2zbKVlcF7XnJDQR83HCsZ6HyP This file package contains detailed DIY installation instructions, software and download procedures. Thank you!
@iCubeSmart4 роки тому
@@JacklynB Dear friend, if you can't open the animation software, please install a DX9.0, the following is the download link of DX9.0. drive.google.com/open?id=1y1AGc2f6znitlyIzTc-edCSFEoTuwm4_ Many computers come with it, but some computers do not have this, you need to install it yourself. Download the linked ZIP file, find dxsetup.exe in the folder after decompression, and double-click to install.
@pavellytkin6938Рік тому
@@iCubeSmart please, help me. Link is broken
@iCubeSmart4 роки тому
Dear friend, You can download a zip file package from the following link of Google Drive. drive.google.com/open?id=1YYw6fDU2zbKVlcF7XnJDQR83HCsZ6HyP This file package contains detailed DIY installation instructions, software and download procedures. The following link is a video of the DIY installation instructions. ukposts.info/have/v-deo/bJFkg4OnoZqFz2w.html Thank you!
@iCubeSmart2 роки тому
Dear friend, Please download the latest electronic information from the Google web disk address. drive.google.com/file/d/1a62NuU_QtyUHD0oo4XSAAWj_dZoWQHCB
@hotrodmatt073 роки тому
WHERE THE FUCK DO YOU DOWNLOAD THE SOFTWARE!!! HOLY FUCK!
@marshalleschete8549Рік тому
I agree. Where the hell is the software. The Google link provided does not work.