Subscribe to this new channel: / @trythisthing Unboxing and testing the cheapest cordless impact wrench I could afford. It is very good for the money. I bought it in LIDL for 79€.
КОМЕНТАРІ: 434
@downloadedxzx9 місяців тому
Upgraded from an older 18v kit. ukposts.infoUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv I independently chose the drill and impact tool, before I came across the kit.I like the 3 speed impact gun. It seems more powerful than my older one, and it can be set to be really gentle. The drill is more appropriately sized for my use. I used to have a hammer drill, but I did not like that it was so big and it was not a great hammer drill. I rather have a smaller drill like this, and then get a corded hammer drill for the odd case I need that.
@dariuszszewczyk31064 роки тому
400Nm seems to be cheap replacement for BMW M3 engine
@MakeAndTest4 роки тому
Man, you made my day hahahah
@piotrradwanski25073 роки тому
@@MakeAndTest also for me :)
@MrKingbesh4 роки тому
It’s ok if you are using it at home u will need a breaker bar for some bolts for 60 pounds impact drive 4 Amp battery and charger it’s not bad + Lidl sell the battery packs for a good price if u need a new battery after a few years , once u have the battery and charger you can pick up other tools that are sold as body only for a very good price drill grinder compressor and much more but if you want a good impact it’s the Milwaukee 2767-20 , if u have a garage Snapon CT8850,
@donegal2010able3 роки тому
I have a milwaukee 1/2 drive served me well one day something happened I don't know what thought it was the battery bought a new one made no difference it could tighten but not loosen well any who was in lidl one Thursday morning didn't even know they did a 1/2 impact bought it and must say it is better than the milwaukee mind you I bought the milwaukee back in like 2009 I'm sure there much better now. On a side note I used a friend's Hitachi hex impact on site driving 8inch bolt's it was like knife through butter it's really amazing how good all these tools work the air compressor is almost obsolete.
@dushk02 роки тому
Need proper impact rated Cr-Mo forged sockets and it all suddenly works.
@screwsnutsandbolts3 роки тому
Excellent video !
@denardou4 роки тому
pour l'avoir achetée juste pour tester (j'ai du meilleur matos mais du coup elle restera dans le camion avec les outils de bases ) : -Vous prenez les douilles d'origines, vous les mettez à la poubelle -Mettez des douilles à choc de qualité et vous verrez que le couple affiché est proche ... les douilles fournit mangent énormément de puissance (acier souple "mangeant" l’énergie) -le témoin de batterie ne vaut pas grand chose Sinon pour le prix et garantie c'est très bien
@MakeAndTest4 роки тому
Thank you for sharing your experience.
@charlescarabott76923 роки тому
I got the dewalt 1600 nm impact because i already had two 5ah dewalt batteries from another tool but if i fpund this at lidil i might have bought this one and saved some money. Nowhere as powerful as dewalt but probably will do most jobs on a car
@AncorPereiraValencia3 роки тому
Hola, donde la compraste a ese precio?
@Amer76R2 роки тому
Im happy with this tool, it easely removes the 36 mm VW axle nut. Thumbs up from me, and the battery lasts really long.
@maxextz2 роки тому
I got one of these and it's really good. Great price too. Aldi do their version for the same price but it's only 180 nm. Parkside stuff is good for the DIY dude.
@MakeAndTest2 роки тому
exactly
@typhoontim125Рік тому
Surely the Aldi one you mention with 180nm is an Impact Driver and not an Impact Wrench. The collet is 1/4 inch & not half inch.
@nisarzaman3 роки тому
Beautiful silent review
@niteblaster13 роки тому
good review😎 the sockets that come with it reduce it's power output as they are not a good fit and they rattle use shorter quality sockets and you will notice and massive difference 😀
@rotorblade95083 роки тому
Yes, force is given by mass and acceleration so basically a hard material produces higher acceleration (deceleration) so a harer socket, harder stud and disc rotor (the studs are bolted into the discs) and a higher mass of the disc produce a greater torque for the same impact gun
@chucky23162 роки тому
How do the sockets stay on mine just fall off. I didn't see this guy putting a pin in either. Do I need a hog ring replaced. I haven't been able to use mine
@chucky23162 роки тому
How do the sockets stay on mine just fall off. I didn't see this guy putting a pin in either. Do I need a hog ring replaced. I haven't been able to use mine
@dushk02 роки тому
@@rotorblade9508 None of that pseudoscience at all! It's just the contact areas and that the socket doesn't deform during the impact. The mass is standing, so a heavier socket would actually hinder acceleration, if it did anything noticeable, that is.
@georgiojansen77582 роки тому
dušan a test would be nice
@momoabdel56944 роки тому
Bonjour merci pour le tuto,et puis ça vaut le coup de l acheter pour la mécanique auto???
@Crocodeal3544 роки тому
Un peu lourde mais utile pour les roues etc je devisse du 200-250 nm et revisse le même
@dmitrys1393Місяць тому
Got mine a month ago and tested it yesterday on some brakes job and i was disappointed with it because looks like the mechanism starts to slip somehow when it's not perfectly aligned, i dont know how it works but the bolt goes easily for a second and then the next second impacting sound changes and the bolt just stays in place and then if you wiggle the tool a little bit the impacting sound goes back to normal and the bolt goes normally again for 1-2 seconds until it stops again. That was super annoying and i had to undo the bolt with hands. Probably defective device or something
@aasgardthor27 місяців тому
Awesome review
@MakeAndTest7 місяців тому
Glad you enjoyed it
@muhammadakhyar84363 роки тому
Can your dellevery to Brunei Darussalam?
@lummeltje4 роки тому
wou eerst een milwaukee stubby 12v kopen maar dit is al prima voor wat ik er mee wil gaan doen! dank voor de video!
@MakeAndTest4 роки тому
Ja, dit is erg goed voor de hele werkplaats.
@jjmmjj99994 роки тому
I don't understand German but I own a milwaukee stubby 12v and was impressed with this tool for less than half the price
@MakeAndTest4 роки тому
@@jjmmjj9999 it does the job
@grazianolaudisio36444 роки тому
Wat ga je doen dan?
@lummeltje4 роки тому
Graziano Laudisio brommers opknappen, en de jaarlijkse bandenwissel
@olivierberg97713 роки тому
Kan je hiermee de vario van een scooter los halen?
@ufs9103 роки тому
Gutes Video gemacht.
@kmieciu4ever3 роки тому
8:36 metalowa brecha wygrywa :-)
@Soni-sGarage3 роки тому
Meiner ist nach 5 Monaten inkl Akku kaputt gegangen 😡😡😡 aber haben ohne Probleme komplett ein neues bekommen. Lg Soni’s Garage
@jmc99794 роки тому
Que modelo es?
@RobertBosch93973 роки тому
Nice video 👌, i bought 2 in Germany, they work excellent 👍
@UltimateTBone2 роки тому
Hi Robert, nice to see you here :-) I read complains on the Lidl site about loosening wheel bolts. When the are tightened with 120NM, only the 400NM stand on the Parkside will get them loose. And tightning with 100NM would be around 75NM. But you're using it on your work, so I'm curious about your opinion.
@RobertBosch93972 роки тому
@@UltimateTBone I don't use it anymore T this moment, it's a good tool but much to light, I bought a milwaukee M18 fuel, 1700 nm 😂😂
@cardo11114 роки тому
You didn't open the box with a reciprocating saw like AvE does ?
@MakeAndTest4 роки тому
Can you give me more context, cuz I don't know what you're trying to ask me?
@cardo11114 роки тому
Insane Builds I Appreciate the response. I was joking, there is a channel called AvE where the creator opens his brand new tools and other items he tests in potentially damaging ways often using saws.
@MakeAndTest4 роки тому
@@cardo1111 Ahh ok. Nice one hahah
@madcatminis3 роки тому
Good video. Thanks 👍🏼👍🏼 6 adverts for a 10 minute video
@henrykinfri1438Рік тому
Ça vaut le coup de l'équipe et d'une batterie de 8ah ?
@martinatrybusiewicz2405Рік тому
Will this be enough for a stubborn sump plug? Or to remove drop link locking nuts?
@Asad-2166Рік тому
Piece of cake
@SBBUK4 дні тому
Drop links yes. For a sump plug i'd stick to a normal breaker bar as you will have a really bad time if you damage the thread.
@GenMaster1242 роки тому
Suggest only using impact sockets and then only six sided ones 👍🏻👍🏻
@J.Santos813 роки тому
Boas. Essa máquina dará para desapertar porcas de roda de camião?
@gtikiller3 роки тому
Não creio, tenho uma é muito boa, mas para isso acho que não. Ha uma versão desta marca de 1600nm que é a parkside profissional que essa sim, dá. E não é cara... Mas dificil de encontrar.
@gamefoorum3 роки тому
Why are you trying 210nm precision when most of the cars have around 110-120nm ?
@MakeAndTest3 роки тому
Yeah I know I messed that up a little bit. But I had to test it on a much bigger number than just 100Nm. Also I dont really care about my car anymore, so it can take a beating :)
@hakansen71913 роки тому
Insane Builds it only tightenes up to 100nm. The other numbers are for loosening the bolts
@stay_jaki3 роки тому
Milwaukee No.1
@hadipewe3 роки тому
do you mind to make some video and release the bolt of front strut ( it is m21 tight at 165 nm, two bolt on bottom side of the strut), also is it possible to release the suspension bolt, the center bolt of front tire
@Ljosi3 роки тому
@@hakansen7191 that's the case with the corded model, but the cordless one does both up to 400 Nm
@faizansportsbikework10903 роки тому
Is brother avilabel in India or not
@joseduarte10213 роки тому
Amigo sabe aonde posso comprar urgentemente uma pistola dessas Obrigado
@rustypanda3 роки тому
Bonjour pour le prix elle semble très correct
@stepankenig29053 роки тому
Подскажи пожалуйста ссылку на litl где заказываешь. За раннее спасибо.
@oleglvl3 роки тому
У Лидл нет интернет магазина. Только в самом магазине можно взять
@SplinterPlay3 роки тому
@@oleglvl вообще то есть
@SplinterPlay3 роки тому
Есть два похожих только в цене немного отличаются 1: www.lidl.de/de/p350791?productId=350791&countryCode=DE 2: www.lidl.de/de/p350790?productId=350790&countryCode=DE А вот нашёл ещё только без аккумулятора: www.lidl.de/de/p355166?productId=355166&countryCode=DE
@dfg95623 роки тому
@@oleglvl www.lidl-sklep.pl/ это в Польше, часто там покупаю. Гайковерт тоже имеется в коллекции, кстати не плох. Отправка только по територии Польши. Насколько я знаю лидл везде имеет онлайн магазины.
@typhoonm.24323 роки тому
How much nm is its resl powe?
@rickilaws9601Рік тому
the black parkside performance model is an animal of a wrench !!! take tractor wheel nuts out with em .... never seen a performance in the UK .. I think they sell them in Europe . it's a serious bit of kit !!!!
@user-vh9si6tu6y4 роки тому
👍👍
@JohnnyTheCache3 роки тому
Its currently available again at LIDL and I have just bought one (model 2021 ASSK 20-Li A1). After many comments here and at the lidl online shop, I was very curious. After a test I can now say: The thing has POWER !! If your device does not open the bolts on your wheels, you are either doing something wrong or you have a defective device.
@MakeAndTest3 роки тому
It's good to know that you have to press the button and hold it for at least 10 seconds for the best result.
@JohnnyTheCache3 роки тому
@@MakeAndTest Exactly, an impact needs some time. Maybe some people expect it to work like a regular screw driver? Well, it doesn't :D Seriously these Lidl things are great for occasional use
@johnlever66963 роки тому
They have been at your lidl already? They aren’t available till a week on Sunday apparently
@JohnnyTheCache3 роки тому
@@johnlever6696 i got mine from the lidl online shop in germany, it has been available since last week and they still have stock
@johnlever66963 роки тому
@@JohnnyTheCache nothing here in the UK till a week Sunday. I’ll have to wait.
@InBoostWeTrust7MGTE4 роки тому
3:40 now that sounds like lawnmower engine
@habibafarin16453 роки тому
I want one, do you sell?
@michaelstubbs4518Рік тому
This gun is good for a mid torque impact wrench but you should never torque a wheel up that high you will sher off the bolts.
@MakeAndTestРік тому
youre right. But I had to test it somehow. It's an old car that I dont use
@overhaulgamerz85528 місяців тому
I agree, don't use this to tighten the nuts, previous mechanic tighten my car wheels with impact wrench and when I went to change tyres, tyre shop had a hard time removing the nuts.
@dalebassett611923 дні тому
I accidently torqued one of my car bolts on no 3 setting on a milwaukee high impact wrench that has 1650 torque it didn't rip off 😂
@DomRivers674 дні тому
So, was it reasonably accurate?...it seemed to take another quarter turn on the lower settings to get to the correct torque
@dennisinanir33852 роки тому
goeie video thanks! LIDL heeft goed spul
@ronin58923 роки тому
Con 400 NM allenta i bulloni dei semiassi é una bomba
@fredjones73074 роки тому
I bought one, works fine. The circlip socket retainer isn't very good. I'll get a couple of ball bearings and a suitable spring and fit one, easy enough...
@valeriocoelho81384 роки тому
A chave tem o maximo binario no fim de 30s. Aqui nem 10s foi aplicado. Alem do mais os valores serao mais corretos com chaves de qualidade
@MakeAndTest4 роки тому
Thank you for the help. I'll try it next time.
@oneummah6795Рік тому
Great video, the torque settings are not true. As a example you would never torque your car wheel nuts more than 120 NM in a majority of vehicles otherwise you can snap the wheel bolt. It makes sense to buy a proper brand like Milwaukee.
@ahmedadegboyega36783 роки тому
I am in south Africa. How can I get one?
@SUNSETRETREATSXM2 роки тому
Goede test!
@johnwarner38093 роки тому
I have bought this from lidl, it's worth every penny , forget all the barmy demonstrations showing it wont tighten or undo to 400 nm, we're not building bloody battle ships, its got more than enough torque for what its intended for .
@gardenfeed92493 роки тому
I was able to hold the socket in my hand while trying to simulate fastening/releasing wheel nuts. Even on max setting of 400 NM, it was possible to hold the socket by firm hand grip, and this just does not meet my expectations. As I always tighten wheel nuts manually using spanner I have a feel how tight they should be. Rarely using torque wrench. Tried the tool on my wheels bolts and it was not possible to release any bolts I had tightened with spanner, torque on the tool was on max setting of "400 NM" but it was not possible to release any. Will continue to use my trusty spanner and this impact wrench will go back to the shop. I like to trust my hands instead.
@dushk02 роки тому
@@gardenfeed9249 I have the basic model and I would pay for seeing a show where a weakling who makes up BS stories on YT tries to hold that down with their hands... And I'd love to know the brand of gloves if that actually worked out. And yes, I've just made a socket pretty hot trying to give that story a shot. Seriously, you didn't xD
@gardenfeed92492 роки тому
@@dushk0No gloves, I was not filming unfortunately , if I ever find the tool I will demonstrate. Btw, battery was 100%.
@kush34242 роки тому
How to buy this product?
@mindaugas19064 роки тому
Good review. With proper impact socket cr-m not original cr-v ones it produces 300+ nm torque. Not 400nm as claimed but still good enough for the money.
@MakeAndTest4 роки тому
Thanks. I've come to the same conclusion. Not the advertised torque, but it will be usefull in the workshop anyway.
@animation01boy4 роки тому
say whats actually the difference between cr-v and cr-m thnks?
@derbigpr5004 роки тому
You don't even need 400 Nm for anything really. Even 100 is overkill for most things, unless you intend to work on tanks and trains LOL.
@mindaugas19064 роки тому
@@derbigpr500 you bet its not overkill... tire shops sometimes overtorque wheel bolts to 300+ nm. Good luck removing them by hand without long bar. This wrench is not strong enough for that. And you always need more torque because tightening torque is always way less.
@Neulich4 роки тому
@@mindaugas1906 everything you said i can confirm. Shops overtightening and ~300nm max. on this mashine.
@s14driver4 роки тому
It is useless for a car wheels removal, 5 out of ten screws won't be removed without breaker bar. Works good on recently mounted maybe greased screws up to M12 thread torqued up to spec or lower. If you would mainly use this for car wheels removal or similar jobs, save up some money and search for min 600+Nm. Good value for small bolts though....
@MakeAndTest4 роки тому
thanks for your feedback man :)
@DashCamSerbia3 роки тому
It removed my wheel bolts torqued at 105-110 Nm like they are nothing. But I used an impact socket with it.
@kayakarakaya48193 роки тому
Then again people who work on their own cars, will generally tighten and loosen their wheels every half year at least and grease them up.
@bigtrev8xl2 роки тому
@@kayakarakaya4819 🤣🤣🤣🤣🤣🤣🤣🤣
@knele47284 роки тому
Kakav je uzivo ,bio sam vidio da lidl ima to u prodaji ,al dal je stvarnih 400nm tj snaga ,i kolko traje baterija?,dal se moze demontirat ,i montirat set kotaca na autu sa potpuno napunjenom baterijom???
@zdenkokurtic8144 роки тому
mislim da bi moglo i nekoliko setova
@MakeAndTest4 роки тому
baterija dobra
@Pfirtzer4 роки тому
Uvek je bolje imati bateriju u rezervu, e tu moze Lidl da zeza malo, iako imaju baterije treba dobro da se rapsitas pre nego sto kupis jel cene jesu povoljne ali ne sve baterije pasu na svaki aparat kod njih. I ja bi kupio ovaj ali ne znam da li da kupim na struju ili na kompresora jer vec imam kompresor.
@knele47283 роки тому
Bilo lidlu, i prvi dan dva sve pokupovalo ,i hvale ih 👌cijena 600kn,jedino da je jos 1 baterija ukljucena top bi bilo 🤔
@pripremaoknobit10793 роки тому
Sad ce bit opet od 7.1.2021 u lidlu 600kn... ali cini mi se da je 400nm za odsarafit saraf na kotacu preslabo... narocito kad zapece onak da moras s polugom...tj nedovoljnu jacinu ima. Da ima 500nm bio bi ok.
@socialghost44004 роки тому
Good review, I bought the very same one in Lidl last week, so far it has worked the charm, my only complains are that it is not a brushless motor and theres no locking ball for the sockets (there is a locking ring tho, and I have not had any sockets fall off either, so not the biggest issue), but I mean for the price, those are easy to live with....anyway....Subscribed!
@MakeAndTest4 роки тому
Yeah I noticed that sparks are shining inside the machine when you suddenly stop it. I just dont understand why are there differences in prices. I paid 79€ some say it was only 59€...
@socialghost44004 роки тому
Insane Builds I guess it varies from country to country, I paid €75 / 555DKK for mine in Denmark
@MakeAndTest4 роки тому
@@socialghost4400 for the same kit? Fast charger and battery included?
@socialghost44004 роки тому
Insane Builds yes, and the four sockets 🙂
@saschaschulz87304 роки тому
Des doch nur Müll des gelumpe
@MakeAndTest4 роки тому
Check out my channel(subscribe) and watch some cool projects being built: ukposts.info/the/1ycLijbbz1xgnxJCO1ipug.html
@user-bp9uo3bz1l10 місяців тому
ប៉ុសផ្សានឹងដំលៃម៉ានបង
@abrahamcoga8424Рік тому
Video muy bien echo 👌👌
@davidcole58423 місяці тому
good demo many thanks
@derwaldmeister39543 роки тому
I compared the torque from this thing to a torque wrench. The torque is not half as high as declared. 400 Nm is not even 200 Nm when loosening and tightening. 200 Nm setting is only 90 Nm. If wheel screws are rusty you can be lucky if you can loosen them. I also own the smaller version of this impact driver. Parkside says 180 Nm. Even if I use the shock adapter of milwaukee I can't loosen a screw what is tighten with 50 Nm.
@MakeAndTest3 роки тому
Great info. Thanks for sharing.
@Ljosi3 роки тому
something is wrong with your unit, or you are using it with a 2Amp battery instead of 4.. I tested mine and it's very close to the advertised numbers (+- 5%)
@rickjohnson87823 роки тому
Should be reported to trading standards . Clearly doesn't offer the performance it says it does .
@mannecorner17373 роки тому
Radmuttern 210nm ?????
@MrPabsUk3 роки тому
I thought you were going to try the crankshaft pulley bolt at the end! Oh well! I think I`ll stick to my Makita 1000nm impact wrench, costs a lot more, but MUCH stronger, will last MUCH longer, & the batteries & chargers will be available, anywhere, for decades..
@MakeAndTest3 роки тому
I'll try that machine next. Wats the specific model?
@MrPabsUk3 роки тому
@@MakeAndTest Mine is a Makita DTW1002Z. Its amazing. Not cheap, but amazing!
@MakeAndTest3 роки тому
@@MrPabsUk I'm glad you like it. If I have time and money I'll test it.
@johnlever66963 роки тому
You can’t even compare the two and it’s silly to do so.
@dushk02 роки тому
Dream on! Using an impact tool for decades... And who wants new batteries on a yr. 2000 battery-powered tool at this age?
@hamzasheikh29282 роки тому
Price nd location
@giovannir.79733 роки тому
carica prima la batteria e vedrai che funziona bene, avevo fatto lo stesso errore.
@gustavomejiacarmonaРік тому
Donde la compro
@jocalibusohump4 роки тому
Good vids sir I wanted to buy soon bec every weekend I go in aldi and lydl here in Carmarthen 😂
@Domenico-ow8jo4 роки тому
test einhell TE-CW 18 Li Brushless VS Impact driver Parkside PASSK 20 L-iA1 einhell 215nm VS parkside 400nm
@stipestipe45603 роки тому
Einhell win 😂
@Domenico-ow8jo3 роки тому
@@stipestipe4560 🤔
@liamhoanzl29203 роки тому
I had an Einhell before and it crapped out after an easy repair , it just doesn't stopped spinning
@williammincher683 роки тому
Einhell and parkside are literally made in the same factory its just rebranded parkside for lidl. Google it
@electricdixie343 роки тому
Brilliant video well tested
@massimo70793 роки тому
Pagato ieri 02/07/2020 59,00 euro alla lidl
@derbigpr5004 роки тому
Hahah I bought this in Lidl too, nothing wrong with it. Will see how long it will last for occasional repairs.
@MakeAndTest4 роки тому
It works just fine for me. All around good tool for a home workshop.
@shalvabenidze70453 роки тому
@@MakeAndTest qué precio tiene?
@MrBadboyrus3 роки тому
how much you pay for it?
@johnlever66963 роки тому
With normal torqued up wheel it’s and bolts will this impact undo them?
@nabilbourouisa3 роки тому
@@johnlever6696 yes, wheels on my car are torqued to 130nm (ideal torque), it does it without problems
@domigashi3 роки тому
Das Problem liegt nicht beim Akkuschlagschrauber, sondern die Schraubnüsse sind von Parkside zu dünn leider, besorg dir die Schraubnüsse von andere Hersteller wie z.B von Bosch, die dicker und stabiler sind, dann wirst du sehen, dass der Akkuschlagschrauber von Parkside sehr gut ist und jede schraube Sekundenschnell aufmacht.
@edinfahrzeugdiagnose3 роки тому
Hey meinst du wenn ich mir die Alufelgen Schraubnüsse von Lidl für 10€ dazu kaufe kriege ich auch die Mutter gelöst oder sind die auch scheiße ?
@makakk03 роки тому
@@edinfahrzeugdiagnose es gibt ein sehr gutes ungarisches Video dazu, hier probiert er mit den originalen und mit den CrMo Schraubnüssen: ukposts.info/have/v-deo/ipmTgHxriWOqtp8.html
@Alexxx2210813 роки тому
@@edinfahrzeugdiagnose ich habe mir auch diesen schlagschrauber gekauft und habe zuerst die beigelegten nüsse probiert. ich habe die schrauben nicht gelöst bekommen. daraufhin habe ich mir schlagschrauber nüsse aus CHROM-MOLYBDÄN gekauft und die schrauben gingen ganz leicht auf. ich glaube bei lild gibt es die auch zu kaufen oder? wenn ja dann auf jeden fall holen. denn sonst wirst du die schrauben nicht oder kaum lösen können
@edinfahrzeugdiagnose3 роки тому
@@Alexxx221081 ok wunderbar danke dir für die Antwort. Werde ich mir dann holen
@leszekm44143 роки тому
Szkoda że ich nie ma w sklepach już
@nadneDonaDon2 роки тому
Jsou porad na prodej.
@poppsmiel47274 роки тому
Un péteuse n'est pas fait pour serrer au couple....uniquement pour desserrer donc normal de ne pas avoir le couplé sélectionné de sur le serrage des roues.. '. Qui doit se faire à la clé dynamométrique dans tous les cas.
@MakeAndTest4 роки тому
Thank you for sharing vital information.
@pdany44 роки тому
C'est du désserrage qu'il fait :)
@poppsmiel47274 роки тому
@@pdany4 pas du tout à 2:30 il montre que sa clé dynamo est au max à 240Nm et ensuite il serre les écrous aux différents couples de la péteuse 200 300 ect... Et on voit que même régler à 300 ensuite il arrive encore à serrer avant que sa clé déclenche ce qui veut dire que la 300 Nm de la clé ne marche pas pour le serrage.... Ce qui est normal d'où mon commentaire 😉
@aspos4287Рік тому
Il est prouvé que les valeurs sur la machine sont à diviser (presque)par deux (voir les autres tests sur UKposts)...
@chucky23162 роки тому
How do you keep the sockets on mate. I have the same tool and they just fall off I noticed you didn't need a pin either.
@MakeAndTest2 роки тому
I mean... you can't turn the machine downwards or else they will fall. I have the same problem
@chucky23162 роки тому
@@MakeAndTest does youres sort of spin on the anvil, I have the smaller lidil impact gun and its much better in its design, maybe I need a new hog ring friction ring
@muhammadakhyar84363 роки тому
Its good..how much price?
@MakeAndTest3 роки тому
199€
@Outdoor-Rider3 роки тому
Learn english
@MakeAndTest3 роки тому
@@Outdoor-Rider Will do mister
@user-rc4pz1gh3l2 роки тому
Сколько стоить?
@DashCamSerbia3 роки тому
I bought an impact socet for mine. You need an impact socet to get better results. They transfer the force better.
@donegal2010able3 роки тому
Too right I've seen a chrome socket explode when trying to remove a seized axel nut, it was like a grenade 3 of us up close just staring seeing if it'll work luckily no one lost an eye or a nose all that was left was the bottom half, it was a decent socket Halfords brand. Impact for impact they are softer and will wear faster but jesus they are safer
@DashCamSerbia3 роки тому
@flip inheck No, it comes with 4 sockets. But they are not impact. They are regular Ch-V painted black.
@DashCamSerbia3 роки тому
@flip inheck Not untill it breaks and sends shrapnel into you. And they don't transfer torque as good as the impact ones.
@rajujaiswal...35922 роки тому
👏👏👏👍
@Pjotr19823 роки тому
Tie dodávané CrV nádstavce sú blato, treba použiť kvalitné chróm molybdénové a dá sa z toho dostať cca 350Nm.
@robertofuentes20084 роки тому
Hola me gustaría saber donde la compraron para comprar una gracias
@MakeAndTest4 роки тому
LIDL
@oliversatory14943 роки тому
Funny. Mine couldn't get the Bolts loose from my car. Why does it work in these videos? You know the answer, don't you?
@MakeAndTest3 роки тому
I heard you have to press the button and hold it for at least 10 to 15 seconds. Only then it goes to full power. Also you must have cr-Mo sockets for better results.
@oliversatory14943 роки тому
@@MakeAndTest I stopped when it started to smoke
@MakeAndTest3 роки тому
Well...thats not good. Refund it. I think it has a 3 year warranty
@oliversatory14943 роки тому
@@MakeAndTest I sent it already back and bought one from Milwaukee. Endless power!
@MakeAndTest3 роки тому
@@oliversatory1494 You like Milwaukee? How does it compare? How much torque does it make?
@medadn183 роки тому
ou on peut l acheter ?
@MakeAndTest3 роки тому
in LIDL
@medadn183 роки тому
@@MakeAndTest il faut attendre ..... et quand elle arrive elle part très vite
@MakeAndTest3 роки тому
@@medadn18 Here it was sold out in one day
@donegal2010able3 роки тому
The 20v range is the bomb, I've collected quite a few of them 14 battery's the first set of 2018 batteries work just a good as new and I use them all the time. Parkside make dam good tools the 4 in one looks flimsy but its pretty handy I use the saw all the time
@12BlackKnight343 роки тому
Damn good tools.... yeah right...
@user-zt4ry9hm9u3 роки тому
There's nothing really wrong with the tools and they are priced well, however they are same Chinese made generic tools that are also sold under many different brands such as Stanley, silverline to name afew
@Asad-2166Рік тому
Now battery charger sold separately 😢
@aemank4 роки тому
Hello is it's a good machine or not please 🇫🇷
@MakeAndTest4 роки тому
good
@aemank4 роки тому
Thanks for answer 👍🇫🇷
@maribaek19833 роки тому
Where can i buy it
@MakeAndTest3 роки тому
I bought it in LIDL
@maribaek19833 роки тому
Give me link bro please
@rondhole3 роки тому
Most Toyota and subaru had 103Nm torque for wheel
@daewooaa-ub3quРік тому
Is it brushless?
@s.g.d.l.811125 днів тому
No
@s.g.d.l.811125 днів тому
Ma di forza ne ha io ne ho 3 uno meglio dell'altro lo porto sempre in auto e va alla grande al bisogno sia in officina, livello hobbyes, che auto 👍👋
@saudinord24812 роки тому
Хороший инструмент для себя и цена норм!Надо брать!
@nadneDonaDon2 роки тому
Бери не пожалеешь. У меня эта версия и та сильная
@user-wu5en9un1oРік тому
@@nadneDonaDon ну и как работает?
@rivasallan47162 роки тому
How much po
@alxrilli4 роки тому
It s 160nm real max
@marcl99192 роки тому
👍👌🏾
@titomiss4 роки тому
Good product or no ,
@MakeAndTest4 роки тому
Very good product.
@bars7871Рік тому
Где такой купить в россии?
@DON_M4RK3 роки тому
Škoda že už ho v Lidlu neprodávají 😑
@jimstreet19943 роки тому
už zas jo ale bacha mě se 2 koupené kusy hned zasekly :D
@DON_M4RK3 роки тому
Díky, ale už jsem ji zakoupil na podzim a při každodenní práci v servisu se drží obstojně (ani 1 se nezasekla)
@yusuf-jw9qc2 роки тому
Great
@nguyent24773 роки тому
Only Makita DTW285 number 👍🇯🇵
@TheBlock-hl9cv3 роки тому
That's weird we had to buy our charger and battery separately wasn't included
@MakeAndTest3 роки тому
It was probably B1 model. A1 normally stants for battery and charger included.
@rodtukker19043 роки тому
@@MakeAndTest Like your torque wrech. Can you put a link to it?
@maumaria3 роки тому
Because the battery fits all the machines of this series