Video shown how to make a hole using step drill onto plastic surface. Vernier caliper was used to measure the external diameter of the connector as well as the inner diameter drilled using the step drill.
КОМЕНТАРІ: 101
@zulfikranzulmos40663 роки тому
How To Not Properly Drill A Junction Box 😂😂
@CityBoyLiewРік тому
Your continuous support is well appreciate. It reminds me whenever I drill a hole. Please continuous to provide feedback. I need it for improvement. Help me growth better. Thanks. Subscribe for more videos.
@TexasAggieNetwork5 років тому
Good job getting the job done.
@CityBoyLiew5 років тому
Thank you.
@tubutieghi5 років тому
All you had to do was cut it out as it is designed to be done. No drilling No risking a stigmata to the palm of your hand SIMPLES
@CityBoyLiewРік тому
Thanks. Ideally it is the case. Unfortunately the cable gland I bought is smaller than the standard size. I suspect one is the mm while the other is inches.
@HotOnionRing4 роки тому
OMG Please do not make any more video like this... The way you handle the drill, the scissors from your grandma, the reason to drill, caliper measure the hole... omg omg omg
@CityBoyLiewРік тому
Agreed totally. Thanks for comment.
@cactuskid19505 років тому
I almost learned something. We need an update to see how it actually works.
@candlemedia3 роки тому
😆😆😆🤭🤭
@Kevin-vx3hg3 роки тому
No update, must mean it didn't work 💀💀💀
@CityBoyLiew3 роки тому
I have checked twice. No water at all. Everything inside look new after two years.
@CityBoyLiew3 роки тому
I have been promoting this to many people when they told me ant is making nest inside when they didn’t use in-line feed through.
@flavius38964 роки тому
Thumbs up for entertaining. :-)
@CityBoyLiewРік тому
Subscribe to my channel for more entertaining videos.
@root8ableРік тому
I still can't find how to pass in cat6 cable already having their ethernet plug installed
@CityBoyLiewРік тому
Any way to drill a hole by the side?
@root8ableРік тому
@@CityBoyLiew on the side, water won't enter?
@CityBoyLiewРік тому
@@root8able Ideally to be at the bottom. The cable gland are meant to prevent water from entering the box.
@Sponge_Bob_Square_PantsРік тому
Naah just cut connector then pass cable
@CityBoyLiewРік тому
The hole appeared to be way bigger than the cable gland.
@hamidhussain3075 років тому
can anyone tell me what those wire connectors are called, with the o-rings? and are they IP65 rated?
@zulfikranzulmos40663 роки тому
It's cable glands
@CityBoyLiewРік тому
Cable glands works.
@AdeMunaa2 роки тому
halo well come back again
@CityBoyLiewРік тому
Subscribe and check back for more videos.
@mmayhem21484 роки тому
whats the point of measuring it to fit when u juss ripped it out with the needle nose...ahaha!!!
@CityBoyLiewРік тому
Ideally wanted for a perfect fit.
@telemetryz4 роки тому
Very poor drilling technique. Drilling towards your hand will eventually come back to "bite you". Also when you are "trimming" ID of hole, use a round file. Makes it simple, fast and safe. Good luck.
@CityBoyLiew4 роки тому
Thanks for the tip.
@cocotug0Рік тому
yep... it bit me once. i was used to cheap used drill bits, then, one day, i was using a brand new 3/8 and had my hand as backing for the sheet metal. when the drill punched through it caught me off guard and gave me a cut with the shape of the flutes along 2 fingers (thankfully very superficial, but uncomfortable and inconvenient)
@CityBoyLiewРік тому
Ya really need to use personal protective equipment.
@americanpatriot27896 років тому
Well that went wrong and he glided through it like it went well..... :)
@thorn36865 років тому
looked fine. Doesn't have to be precision fit because the gasket is the sealing surface..
@CityBoyLiewРік тому
Thanks for clarification.
@omega_hb48955 років тому
There’s a knock out piece and there’s no need for a drill . It would be much faster and easier. Thanks anyway.👍🏻
@CityBoyLiewРік тому
Unfortunately the cable gland I bought is smaller than usual standard size.
@mohammedtahir7281Рік тому
Meterial name?
@CityBoyLiewРік тому
Which material referring to?
@mohammedtahir7281Рік тому
@@CityBoyLiew sir i want to manufacture electric pvc junction box, best quality,
@mohammedtahir7281Рік тому
@@CityBoyLiew ur. Meterial name?
@stephenc41612 роки тому
3rd step drill lolol. And he ended up going maximum anyway. Just use the knock-out provided...geez!!
@CityBoyLiewРік тому
Check out my another video for using the knock-out hole.
@dtwistrewind73614 роки тому
The finished product was wrong, you didn't have the bottom gland clamp screwed on.😀
@CityBoyLiewРік тому
Check this out. ukposts.infoT1yPecmmb9c?feature=share
@shanghaiwinman45772 роки тому
What you've been looking for the PU Chemical for your this waterproof junction box gasket foam with Waterproof and fireproofing function, should be here ukposts.info/have/v-deo/nKNjnZ5vhIx-t4E.html
@CityBoyLiew2 роки тому
It will be nice if consumer product that allow user to replace their own seal using the PU chemical.
@davidforan2983 роки тому
Is this Ladka from Taxi?
@CityBoyLiewРік тому
I don’t think so. Subscribe for more videos.
@dyancatamaran40164 роки тому
You should do it more carefully and with much better technique.
@CityBoyLiew4 роки тому
Thank you. That happens during video recording.
@jackhewison52463 роки тому
Cutout too big and no rubber seal under the nut!
@CityBoyLiew3 роки тому
That was the model I bought that’s compatible with the outdoor three core wire used.
@craigr3063 роки тому
Can I buy this crap on eBay from Hong Kong
@CityBoyLiew3 роки тому
Suggest to start with the keyword in the title and look for any similar products. Perhaps Lazada should have as well.
@raymondsteane68513 роки тому
How not to do it !!!!
@CityBoyLiewРік тому
Yup, should be vertical. That was a good learning experience. Thanks for all the comment to remind what not to do. Subscribe to my channel to provide more comments.
@Diablo8900Рік тому
wow, a man who don't know how to do this...
@CityBoyLiewРік тому
A record of how to tackle the unknown.
@zulfikranzulmos40663 роки тому
Not only just horrible but the finished product u showed didn't have the front cap to hold the cable tightly..
@CityBoyLiewРік тому
Luckily installed this on not so exposed to rain. Thanks for the head up.
@smudgersmudge19224 роки тому
How NOT TO do this correctly - look away any DIYers before you hurt yourselves...
@CityBoyLiewРік тому
Agreed totally.
@ScottSmithPhotos2 роки тому
My gland hurts.
@CityBoyLiewРік тому
Lol
@arlequinantarius8586 років тому
Te grande el guego
@CityBoyLiewРік тому
Bienvenido a visitar mi canal nuevamente y compartirme su opinión.
@Rima-hh8db5 років тому
No utility knife? LOL
@CityBoyLiewРік тому
Not recommended because it will crack more than it should be. I still find drilling the best way.
@dsmale7067Рік тому
City cowboy, donkey outside
@CityBoyLiewРік тому
Get things done!
@zulfikranzulmos40663 роки тому
Lbg tu dah ade kan 😂
@CityBoyLiewРік тому
Besar lampau.
@grimpuppy53613 роки тому
This was ment to be a funny video right? Lmao@ keep drilling and measuring until you drill a whole the size of the knockout... classic. I hope that caliper is calibrated and certified.
@zaimhazmin8851Рік тому
fits the definition work stupid and not smart😂
@CityBoyLiewРік тому
Quite entertaining I watch it now. The core idea this channel was setup and made public. Welcome to subscribe to my channel to watch how I growth. I found this beautiful. A report of how I self-learn by actually doing it.
@barnabyreynolds74974 роки тому
this video, is not helping you (your ratings) or the consumer. thanks for the intent, not for the content.
@CityBoyLiewРік тому
This video always reminds me of how to do things in a save way. Luckily didn’t break any fingers back then.
@BHP154 роки тому
are you kidding?!!!
@CityBoyLiewРік тому
An example of self-learn can be harmful.
@farhanakhan2785 років тому
Hole was to big especially sinve you were using vernier calipers followed by a pair of scissors you borrowed from a museum. Also the dome gland has a rubber washer and not an 'O' ring. Then you forgot to first push the grommet in place. The grommet is the rubber ring that you referred to as a stopper.
@damon3235 років тому
Strange question, but I’m installing my own security camera setup. I want to get some small junction boxes like this to mount my cameras to. The reason being is that each camera has a pigtail to connect the Ethernet cord for power/network. Anyway, do you think it’s possible to mount my cameras to the lid of a PVC junction box like you see in this video?
@CityBoyLiewРік тому
Have you tested it out by now? It should work if the camera is not too heavy. However the PVC box can’t be placed outdoor with direct sunlight. The plastic turns white and will becomes brittle.
@CityBoyLiewРік тому
Thanks for feedback. UKposts is my best place to learn new things. Appreciate that you make time to illustrate the difference between those terms.
@williamlowther7051Рік тому
how to make a mess of it, some people shouldn't be allowed tools, stick to pens and paper,
@CityBoyLiewРік тому
When I first started to learn use a battery drill. That’s how it turns out to be. I hope this video and comments will help inspire newcomers for electric drill.
@beggerkingРік тому
Looks dangerous...
@CityBoyLiewРік тому
Indeed created an awareness about how to work without getting injured.
@zulfikranzulmos40663 роки тому
Really stupid idea coz the hole for cable gland is already there.. U just need to poke it out 😂😂
@CityBoyLiewРік тому
The hole size was a little too big so decide to make a hole instead.
@infectedbyrage13079 місяців тому
This was painful to watch
@CityBoyLiew9 місяців тому
I hope people will find a way to make it done better.
@dalejohns2073 роки тому
this is awful
@CityBoyLiewРік тому
Subscribe for more.
@alpachino4683 місяці тому
Doofus, next time use a file instead of your rusty scissors!
@CityBoyLiew3 місяці тому
Apparently knockout holes can be punctured easily: ukposts.info/have/v-deo/kHiaZZ6fjZuf1Zc.html
@vicomedia1Рік тому
you struggle with this kind of stuff, huh... maybe give up the UKposts thing...i'm just saying...
@CityBoyLiewРік тому
My channel is a record of my learning journey. A self thought DIYer from no technical background to now. I’ll laugh at this too when I watch this video again after many years now. My country does not prepare us as students to be technical savvy. Subscribe to my channel to see how I have improved over the years. Welcome to visit again. Thanks.