Very good video, a must watch. Full of ideas I would not have thought of. AAA+++

Great idea! One caution, dangerous yo use power tools with gloves or sleeves

I love these “ tips”. I’ll call the ER and let them know you’ll be there soon.

thanks a lot!!! the second one is what i need!! good thing i already have the 2 clamps similar to yours.. been searching for a router trimmer jig that can make groove in the middle of the edge

A proper quick n easy diy router table. Couple boards stuck together and pretty much good to go

I did #4 with aluminum L-profiles like yours but mounted them on the table. I used a wooden plank with a groove in it to put my router on and flatten 15 planks with it for my staircase. Was quite a bit of shavings (a 70 liter bucket was filled to the top)

Never run a piece of wood between the router blade and the fence. Very dangerous.

The takeaway for me is the locking pieces for the router. In my case using that idea for my circular saw. Good job!

Saya selalua setia menonton Vidio anda. Menarik dan banyak menginspirasi saya. Tq

Pretty simple jigs that can be easily built. Thanks for the vid!

I'd love to see #4 with some sliding feet on the bottom that can clamp against the piece and hold it at 90 degrees 👌 Great little jigs spawn so many ideas!

I am new to wood working and using the minirouter which i acquired recently. This video gives great ideas to beginners to get going. Thanks a lot.

Nice video but please know that gloves won't help for safety when working with power tools. It's even a bigger danger wearing them. They can get tangled in the router bits or saw blades and your hand might get pulled into the bit or saw.

I didn't think I could work out a way to make a routing table for mine THANK YOU! this will open up a lot more project for me.

You shouldn’t wear gloves around a router but or a table saw or anything the spins. It could grab the glove pulling it into the blade or bit and mutilate your hand.

Please don't use gloves while using a tool with rotating bits... If you have to ask why: Give your router bit a finger and it takes your whole hand.

Thank you for sharing your superb ideas.

Parabéns pelo ótimo trabalho tenha sempre um novo amanhecer

Superb idea 💡

all good, but the last one was really creative.

I like these ideas. The last one gave me the thought that the pattern of the cut could be changed by the change in the lobe of the cam. Similar to that of some sewing machines using differnt cams shapes for different stitch patterns.

#4; why not make a fence to hold your part straight as you're cutting across? I noticed you can easily get a non-perpendicular cut.

Pushing the material the wrong direction. Wood should travel in direction opposite the router's rotation

Çok güzel projeler yapıyorsunuz. 👏👏👏

Did a lot of this stuff 40 yrs ago, great to see it new to someone.

Your ide verry good, inspiration to me, thanks

Je fais des gabarits en tôle d'allu qui réduisent les hauteurs

A good device. I'll make one for myself.

Thanks for sharing

These are solutions to real problems for sure. Not to take anything away, but it seems like some of these have far simpler solutions..

F'awesome TIPS!! Thanks a ton. Quick question: Is the hardware you used in #3 made by you? If not, where does one find that hardware? Again, thanks again for the eye-openers!

Some very useful idea's there bro 😁😁🤘🤘

Great job

Thanks, reques for farmers n garden

hi this stuff is new to me. close to the beggining u put jig on desk thenu routered out a slot how did u know where to start and stop

super good tips .

Good for hobbyist level results, but those are a nightmare to set up and there are way to inaccurate to give repeatable results. You' re going to spend even more time sanding after that to fix the cuts

great channel

These are genuinely brilliant ideas. For the garage shop God that I am, I would have never thought of these. Thank you!!

Thanks!

Nice tricksss

Excelente trabajo podría obtener información sobre las medidas de los materiales

What is the name of those special clamps on #2 ? And what is the name of that router guide on #3. Great videos. Thanks for sharing.

The first 2 i can do with a vice and 2 blocks if wood... 3rd i can do without making aditional parts, 4th i can do with just the router n taking my time, and last well not sure what use that is.

ممتاز

Some great ideas thanks for sharing l

This was great, thankyou. Just discovering all about routers and looking at starting with one of these small trim routers so the video was super helpful. What are those clever rubber ended clamps used in tip 2 jig set up?

Nice video, but would have appreciated narration vs so much music

Awesome Video.. Thanks for sharing

Excellent very good ideas thank you

Cool ideas! Will use them.

Bhai toggle clamp kaha se liye?

I'm used to larger, corded routers ukposts.infoUgkxfQ5_mgwq6PcudJvAH25t-I4D-3cTPz4z so this was a different experience for me. Basically, this is an incredibly sweet machine, fits well in the hand, etc. It has slightly less power than I'm used to, but that's understandable. Maneuvering freehand takes some practice. These days, it's especially nice to be able to avoid power cords. This is above the level of a hobbyist but below a pro level.

In the 1 tips, only the fence is attached, it is dangerous (not equal load on the spindle) and you can see how the whole bends. The 2 tips can be replaced with a carpentry vice and this time a well-used ruter fence will be parallel and not all swing. The 3 tips, again, a wrongly used fence is too high above the ruter bit and bends, the whole thing is useless because you only need to properly attach the fence and use it as a compass without the plywood. 6 tips is very nice but it was spoiled by poor workmanship, a crooked circle and again a fence attached the other way round, you can see the uneven pattern. I am carpenter and I believe that such own devices are very good, but they must be well done because they can hurt somebody. If something is incomprehensible please write, I used the translator.

Thanks.

PLEASE DON'T EVER USE GLOVES WHILST OPERATING A ROUTER !!! When it has grip on the cloth it's allmost impossible to remove your fingers.

C'est très bien ce que tu fais mais tu devrais profiter au max de la hauteur de coupe de la machine, sinon good

Great Tips ... THANK YOU VERY MUCH INDEED

very good.

Thanks for the ideas, appreciated.

I like it 😊👍❤️❤️❤️ keep it up 💪👊

Thank you bro

Gênio!!!

You need a guard around that cutter going 25,000 rpms !

Ide yang sangat brillian

The last one is more interesting

BRRRRAAAAAAVVVVVVOOO!!!!

2:00 you are feeding the wood in the wrong direction!!!... Very dangerous CLIMB CUT!!!

4:00 What do you call these clamps with the red handle? Do they have a specific name?

👍👍👍👏😁

Rent per mil sakti hai kya.. Ye machine.??

If you want to know the worst way to make a jig for a task that's better done some other way...watch this video. Good video since it shows how not to accomplish 5 tasks.

💁❤️

Ist Tragen von Handschuhen nicht gefährlich beim Arbeiten mit Maschinen?

Hi dear Mr.Junkyard,could you tell me how to connect you?we want to cooperate with you,look forward to your reply,thank you.

Junkyard-the Origin of Creativity? Must be why everything looks like junk there.

6:18 mind your fingers ! I have injured my left arm, because the router jumped on my arm during the operation.

You are very creative and smart man 😎👍

tolong buat alat penyedot bensin dari jirigen

1. Milling cutters running open, that is dangerous crap, and you mill against the cutter and not with the direction of rotation. 2. And certainly not with gloves. Ideas 2-5 are ok.

You can basically do everything in this video with the attachments that came with that router - what a waste of my life

Stupeddd😀😀😀😀

are you using GKS 7000?

some interesting ideas, also try not to play the same song over and over again

Sir router bit kinsa kharide

Gloves with a router OMG

They all seem unadjustable! (1 size circle, edging 1 thickness of board.)

As to tip #5.... I can make wavy lines with any router without that jig. Hell, I make wavy lines WITH any jig.

Нельзя работать при деревообработке в перчатках . Только голыми руками .

Название ролика переводится примерно так :как на всякой мелкой хрени медленно но верно ушатать кромочник.

Never wear gloves when working with power tools

that first one where you mount the router on one point on its side is asking for trouble! I stopped watching right after..

How to complicate simple jobs and how to re invent what is cheaply available tools. Dangerous.

Well shit #1… I could have just clamped the piece down and ran a templating/flush cut bit, but instead, let’s make it exponentially more sketchy and time consuming

#5 - interesting. But non-repeatable and the waves you make are not concentric - meaning the peak of one wave is more rounded and the other peak is sharper. Don't mean to be the guy who finds problems with the solution - but - if you're going to teach - do it right.

Junk music kicks your brain off. Like someone hammering nails in the forehead.

Why not give it a try? Dlaczego nie spróbować? ukposts.info/have/v-deo/o5F3fWysfoyopGQ.html Różaniec Do Granic Nieba - Maciek Bodasiński o planie Boga..... Rosary to the borders of heaven

you should NEVER wear gloves when working with fast rotating machines!!!!!!!

Do not use gloves with this tools please

Мдэээ,бедный триммер-такого бреда я ещё не видел