Learning to solder tiny SMD components with a soldering iron

  Переглядів 5,438

John Aldred

John Aldred

День тому

SMD soldering is something that I've put off for ages. I finally decided to give it a go with the soldering iron and I have to admit, I'm not a massive fan. It's doable, for sure, it's not that difficult after a little practice and in some ways, it's a lot faster and easier than dealing with through-hole components, but it sure is fiddly!
The soldering irons used in this video are the TS100 and the Pinecil Pine64 with AIM 62/36/2 eutectic solder and MG Chemicals 835 Rosin liquid flux.
TS100 Soldering Iron - s.click.aliexpress.com/e/_Dks...
Pinecil Pine64 Soldering Iron - s.click.aliexpress.com/e/_DBo...
AIM 62/36/2 Solder - www2.mouser.com/ProductDetail...
MG Chemicals 835 Rosin Liquid Flux (US) - amzn.to/49bTtJR
MG Chemicals 835 Rosin Liquid Flux (UK) - amzn.to/49awe32
LED Soldering Practice Kit
Amazon US - amzn.to/4bwaK2a
Amazon UK - amzn.to/48cdLSn
AliExpress - s.click.aliexpress.com/e/_DB4...
Like the music in this video? Visit www.hooksounds.com/ and enter code "johnaldred" on checkout for 10% off your monthly or annual subscription.
00:00 Introduction
00:46 SMD Practice Kit components
02:26 New toys!
02:47 New soldering iron tips
03:34 Pine64 Pinecil soldering iron
04:17 PCB holder clamp
04:33 MG Chemicals 835 liquid flux
04:43 SMD Practice board overview
05:37 AIM SN62/PB36/AG2 eutectic solder
06:11 Soldering 1206 components
06:32 TS-BC2 soldering tip
08:38 TS-I soldering tip
10:57 TS-B2 soldering tip
13:05 TS-D24 soldering tip
15:03 Soldering tip comparison
16:35 Pine64 Pinecil power tests
20:58 Soldering 0805 components
25:23 Soldering 0603 components
27:42 Soldering 0402 components
30:13 Soldering the main circuit
32:36 Soldering 0805 LEDs
33:00 Checking LED polarity
34:48 SOT23 Transistors
35:19 Drag soldering SMD ICs
37:50 Powering it up - FAIL!
38:26 Fixed it!
38:53 Outro
Gear used or mentioned in this video series...
US Links
Panasonic GH5 - amzn.to/3UwEsht
Panasonic G85 - amzn.to/49awgYI
Panasonic GX85 - amzn.to/4bxMjkK
Behringer U-Phoria UMC404HD - amzn.to/4bBTngf
Rode NTG5 shotgun microphone - amzn.to/42ENNWn
Feelworld FW279 - amzn.to/4byq1iL
UK Links
Panasonic GH5 - amzn.to/49uI0Vx
Panasonic G80 - amzn.to/3SRubLw
Panasonic GX80 - amzn.to/4bvU9eN
Behringer U-Phoria UMC404HD - amzn.to/4bxMe0q
Rode NTG5 shotgun microphone - amzn.to/3OFbDvg
Feelworld FW279 - amzn.to/3SRINun
--
Some of the links in this description may be affiliate links which provide a means for this channel to earn an income and keep producing content at no extra cost to you. Find out more on the About page.

КОМЕНТАРІ: 11
@JohnAldred
@JohnAldred Рік тому
This was more fun than I expected it to be but way less fun that I was hoping for!
@janplexy
@janplexy Місяць тому
PRO TIP: FLUX IS YOUR FRIEND.
@macmccune21
@macmccune21 Місяць тому
Perfect video for me. Im trying to learn have a junk keyboard (e waste) with a bunch of SMD resistors and transisitors and I can get some off, but once I get one end soft the other end cools off! Feels like a hot air machine would make easy work of them, but I have a bit of solder wick and once I get them off I like to practice reinstalling.
@bill6943
@bill6943 Рік тому
More Flux. I generally put flux down on all the solder pads before I start placing components. I usually pre solder all the pads with just a very small amount.
@sylvianeta
@sylvianeta 5 місяців тому
Hi, thanks for it. Do yoou have this paper . With components values.?? I have dificult to identify each one.
@HappyHermitt
@HappyHermitt 4 місяці тому
Solder paste with iron would work too
@thenextproblem8001
@thenextproblem8001 Рік тому
I'm not a professional microsoldering guy but some tips may be useful for you. First of all you never use flux. Big mistake for those irregular joints on almost every component. How much flux is extra? There is no such thing. Use flux whenever you want. And if you want to solder with solder itself after one side is completed use flux then grab the component from middle between your tweezer. Solder the joint you just fluxed. Then move on the next pad. You will see it will be shiny like factory-made. Next tip is to use solder paste. You don't need a hot air or plate (but definitely recommended) you can use your ts100 to melt and solder them. İt will be so much easier. And use flux. With hot air or plate this board will probably takes only a minute to complete. And use flux. 🙂
@JohnAldred
@JohnAldred Рік тому
Thank you for the tips! I had ordered some solder paste but it hadn't arrived in time. Pretty much impossible to get leaded solder of any kind in the UK now so had to order from China. Taking a while. :)
@thenextproblem8001
@thenextproblem8001 Рік тому
@@JohnAldred then use flux :)
@nickk6109
@nickk6109 Рік тому
I think I have a dead ADC.. QFN 48 pin.. should prove interesting challenge.
@JohnAldred
@JohnAldred Рік тому
QFN still scares me, lol. Good luck! :)
Learning to solder tiny SMD components again - With hot air this time!
31:14
SMD Soldering Tutorial | Guide | Tools | Tecniques | Stencil
22:50
Electronoobs
Переглядів 1,1 млн
Піхотинці - про потребу у людях
00:57
Суспільне Новини
Переглядів 1 млн
Cheapest way to learn to solder
23:35
bigclivedotcom
Переглядів 124 тис.
How to Solder Surface Mount Resistors and Caps
5:25
SolderingGeek
Переглядів 33 тис.
How To Learn Surface Mount Soldering
37:20
root42
Переглядів 17 тис.
Soldering Crash Course: Basic Techniques, Tips and Advice!
16:11
Best hobby soldering iron? Pinecil vs. Miniware, Hakko, Weller and Ersa
24:57
Made with Layers (Thomas Sanladerer)
Переглядів 671 тис.
PINECIL - Soldering Iron w/a RISC-V Processor!
6:49
Level1Techs
Переглядів 91 тис.
Inside the Most Famous Chinese LED Factory
19:58
Strange Parts
Переглядів 780 тис.
How to Solder Surface Mount parts (it's easy!)
18:53
LeoMakes
Переглядів 459 тис.
Apple Event - May 7
38:22
Apple
Переглядів 6 млн
Самый маленький Iphone в мире!📱(@ghoul.arena)
0:22
Взрывная История
Переглядів 362 тис.
Which Phone Unlock Code Will You Choose? 🤔️
0:14
Game9bit
Переглядів 6 млн
Я Создал Новый Айфон!
0:59
FLV
Переглядів 2,9 млн