Spy camera in a clock: ukposts.info/have/v-deo/jpViaomssI6ltac.html

Ahh, the incisor wire stripping technique (off-camera). PRICELESS!

17:30 - Quick tip. Tape the camera down with some Kapton tape. Tape the four wires down close to where they will go also with Kapton tape. Hold them in place with tweezers to aid soldering.

For those asking how he found the camera pin connection diagram: Using multimeter before removing the camera from phone motherboard, then 1. GND is very easy to find, it is shorted to GND of the phone 2. V+ is the 5V input from phone (this might be the hardest to find if you don't have experience in tracing the input voltage). Find pin that has no connection with the GND (but there might be more than one). The OP found out using diode test but does not show which one to test. Another way to find out 5V rail is to find the Power IC or Mosfet that gives the 5V to whole motherboard and find the direct connection. While the data lines are typically not directly connected to power rail (it has connection but has pull-up resistor like 10k Ohm) but directly connected to one of motherboard SOC leg. 3. Then the rest of D+ and D- are found by trial and error (using permutation). First, the testing is done by soldering & jumpering the pins of the camera (while camera still attached in phone board) directly to USB and then PC as seen in 8:09. And NOTE that only some cameras support direct USB interface. So, this will work only on few phone models. And if you guess the 5V line wrong, you might permanently damage the whole system.

I like how you were slow to tap the screen in sync with the recording that was playing on the phone to make this look legit

Great for finding out if something you've misplaced has fallen behind a dresser or book shelf without having to move it to see what's back there.

Great work! I thought I was the only one who makes things like this..plus great soldering job, especially not using a super fine point soldering iron! Those camera wires are damn hard to see and work with sometimes..Keep up the awesome work! Just subscribed..

Great video. I love how you are able to get close up. I just subscribed. Love your work.

muy muy bueno el video lo que me uvi9eragustado es que puedas explicar ..por partes sobre la camara saber mas

It's amazing that used cellphones can be used in the hands of creative people like you.👍🇮🇩👍

Owesome project 👍... What phone model and how did you find the usb pin???

What a fantastic video! Very well done! Up close viewing with the specifics. Written out what was needed to know. Very very well done!! Thank you for sharing this!

I need this to look inside engines to see burnt ir bent valves to show my customers. Perfect. Must do this project.

Just simple and neat - Great

Great project ,I would like to ask you how did you find which wire you need.And the wires function

You know all the perverse uses that could be made using that thing, it's MAGNIFICENT!!! :)

Obrigado pelo conhecimento

You are doing great work 👍

سلمت يداك رحم الله الي يعلم بلا بخل ولا خفايا الله يبارك فيك

Transporting old camera lens with an otg usb.. Wow.. Fantastic..

Absolutely amazing advice ♥️♥️♥️

What should be different about connection pins when connected to multimeter

Bro I'm new one here ❤️, awesome video , can you show more clearly how to find out the pins of the camera

A very nice device that should be installed at home for protection

Absolutely amazing advice

i didn't find tbe schematic, how to identify the wires ? good work👍

Mobile Phone camera modules follow MIPI protocol mostly. I wonder how you have managed hook it directly to USB. Please post a brief about interface topology.

انت حقا مبدع رغم طول مدة المقطع ولاكن كل دقيقه فيه مفيدة جدا ويستحق المشاهدة وحقا انت تستحق الشكر والتقدير

Wire diagrams would help us.maub fte some kind of directions to where to soder them on the camera.

Excelente video y muy útil; gracias por el aporte .

This is absolutely amazing advice

No first you have to break it apart remove vibration motor completely then speakers completely then find back lighting wires make mini switch to disable screen . This will keep you from getting cought.

Mini spy camera in awasome My query 1) does the mini spy cam for recording also for hours 2) where can we get the surface paper as used in this project

What was that thumbnail...🤫🤣🤣😂 Anyway good idea..

Good! I think it may help to read part number from components especially to those who have sight problem like me .Tnx!!!

Wow without any module? Or driver board?

Nice project but how to identify the wires in golden paper board?

I really liked,it thank you

You're amazing Brother, Nice Work No comment.

Can you replace the usb with receiver for wireless transmitter with about 2km range?

Привет! Классно придумал👍 теперь нужно эту мини камеру подключить к wi-fi модулю.

What a good carnal video, a question, how do you know which pins to use?

Hello my friend!. Do U know by the way, to make the same with an old blackberry camera? It's also good to know the pin values.

😂What a beautiful idea. No component no IC. Excluding the important things, a beautiful spy camera was made.😝 Thank you😅

But how do you know the difference between the positive electrode and the negative electrode? Thank you for the idea

Would be easier with a much smaller tip when soldering small components together

that was a cool vid to watch but not sure why you wrote down the numbers on the pad ? also i have a challenge for you the nerf nightfinder scope is very basic IR scope the leds can be swapped out for better ones but the screen inside the scope is bad and the zoom is a digital zoom on a tiny pixel screen any chance you could look to improve it some how would love that vid and then i could copy to improve my own lol keep up the great work

hopefully the next video will include the speaker and how to do it .. Thanks

The finding pins is a mistery...

wow. good job bro 😍

Mas bro..mau nanya ..ni..bukan jcsat 4b udah off air skarang..atau pon ma c ada lgi..

Hola en donde puedo conseguir este tipo de cámara y a que precio

Oh vainglory haha, i love it, too

8:35 hello bro why you selected it in diode range? What pinouts you targeting at this point

Wow that's awesome idea, plzz can i hv more of the videos thanks,

Hi Thank You For Your Beautiful And Special Videos And Channel ❤️❤️💐💐

Awesome!!!Great job!!

You're amazing bro..just great🔥🔥🔥

Absolutely amazing

as long as we didn’t know we had such masters

great work bro love and support from Engineering Fun And Crafts

How did you seperate or analyze the input (data in ) output (data out) pin connections ...it is not clear ....and why did not use the right color code during soldering?

No entiendo para que soldar el USB, puedes hacer un plano para las conexiones del flex de la camara gracias

Very Nice. Have to try this to I have thousands of old phones

This is been something I have a problem with anyone who claims they can use any pins on the camera module to USB conversion. It just doesn't work that way. I guess he meant to show the camera module number at the beginning from there he took down the numbers 12, 4, 16 and 20 for this module but he doesn't show the part where he supposedly read that from some module white paper. In any camera the control module has a make and model.. you can search for information on the web.

Great idea i can keep the flash? Better for look inside de wall dreain pipes.

مشالله..عليك...كنشكرك..علا...هادا..فيكرا..راءيعه..

I have a mic which is familiarly used with CCTV camera's. I wanna use that mic as a external mic for videos. 4 wires are there... Shall i make it like this??? One side Micro USB & another side mic... Do you prefer any app to record my audio if i made???

Impressive eyesight and zoom from the cameraman.... As a fellow bot, I can relate to this

22:53 самые лучшие провода зачищенные своими зубами...🤣 Я всегда так делаю сам.

Super bro .now I going to try with my old phone

how do you find the output and input of the camera?

muito bom parabéns vou fazer um microscopio

agradeço pelo conhecimento "congratulations"

Woow, i want to try it. Good job bro

what do you think would be the latest (potentially best) phone camera with usb-controller built in? because i guess modern phone cams won`t have that usb controller built in or do they? if they did everybody would do stuff like that instead of buying expensive webcams right? would be crazy to use some ludacris multi camera from a Huawei or IPhone as a usb webcam. Do you think there is any way of making that reality? like with an external usb controller? but what kind of protocol do these modern cameras speak? is it something like those 15pin RasPI cameras? Please contact me if you are Interestet in this Topic and share your knowledge, I`ll be researching that topic because i really want to do something similar like you did here but with an actually good Camera. Btw. love your videos, keep it up!

I really like your pliers 😅 where did you bought it? 😂😂😂

Amazing! I'm new subscriber.. you have a tutorial to find d+ and d- and positive?

Super nice idea lods..thank you for sharing this video...👍😁

Thanks👍

congrats :)) good work

How to know the connection im confuse

Spy camera saya suka dgn karya Abang , sehingga menambah pengetahuan bagi saya pribadi dan masyarakat umumnya. Trima ksh ya ... Sdh membagi ilmunya

Wonderful work😊👍👍👍

Over voltage and under voltage protection circuit please sir

Give a specific diagram for the wire connection to camera, that would help

Muy buena para inspeccionar motores sin desarmarlo

what accessories to by use ty

Well, great video but you should at least showed us in a schematic diagram where those wires are attached on the camera. I mean, we saw you solder those wires but we don't know which is positive, ground, data+ and data-.. I don't also understand how you traced the pins on the camera using the multimeter. If you could speak in your video explaining things would be very helpful.. Thanks..

how to find camera connection s well

Love it's where to buy black cord USB??

Well done....nice work👌👍

how to identify the wire terminals to make the cctv spy camera at home makes a video

U r the hope as well as the inspiration of many hobbyists my mate... 👍.. ur ideas are lot surprising nd impressive... Thank u for sharing to us... 'The Man and the Technology'..🙃

What the pins connections? How you it testing?

Sangat telaten om... pengen nyoba juga😀

It is assumed that the colors of wires are bound together with numbering... thank you

HEHE BOI... i have like 3 broken phones ready to be used on something cool update: all of 3 have too much near terminals, wich will damage the camera and i will get mad and broke everything because i spend one week on that project, or it will just won't work and i will get mad and broke everything because i spent one week on this project :(

I have no experience in electronics and I need to do the project with a Samsung G313F camera, but I did not know how to identify the signal from the pins to connect it; Could you help me?

How did you know and find which are the connections of the camera from the pcb?