Buy Best Conduit Bender from AMAZON amzn.to/3Ku17mw
КОМЕНТАРІ: 36
@bmcfad122 роки тому
I know you’re just showing the proper way that you should do it but honestly how many guys even put the vendor on the floor for a 30° offset or any offset for that matter other than a 90°? Most of my bending as an apprentice I’ve been taught to do in the air
@adams6798Рік тому
Great video but explain to people how multipliers are found using Trig?
@mohammedhassani39754 роки тому
good job
@jakirsheikh26313 роки тому
how need majarmant
@glennmann6343 роки тому
Great video. Thanks for posting. Nice looking bender. What brand is it? (Thanks in advance for the answer.)
@passionateengineer043 роки тому
Sorry i didn't remember the brand.
@Bapuji42Рік тому
This doesn't show how to use shrinkage to calculate for a given distance between the end of the conduit and the beginning of the first bend.
@tragan1442Рік тому
Soon to be cw here thanks for the vid
@ryanb18744 роки тому
Does the diameter of the conduit have anythi g to do with the "shrink" or is it all treated like a thin line?
@passionateengineer044 роки тому
Consider it as thin line.
@mariamontolla59784 роки тому
Ok!! How tje eff do you find the multiplier
@ryanb18744 роки тому
The multiplier has to do with the angle, it's 30 degrees, sine of 30 = .5. But we are dividing by SINE 30, so it's like multiply by 2. Get the uglies manual.
@diazaa3 роки тому
45=1.414, 30=2, 15=3.86.... Those are the only ones I have memorized.
@lazarevic953 роки тому
a way to find the multiplier for any bend angle is - 1/Sine(angle
@diazaa2 роки тому
@@lazarevic95 Hey now, dont give away these magical tricks of the trade!!!
@diazaa3 роки тому
Depending on bending angle you should put your mark on the tangent of the angle. In this scenario you can see that the mark is in front of the bend as it should be in the center of the bend. This is important if you need the bends to be in an exact location.
@AngelRomero9552 роки тому
How do I put at mark at 0.57735026919?
@diazaa2 роки тому
@@AngelRomero955 .57 degrees?
@AngelRomero9552 роки тому
I found in another video that when making parallel runs with offsets. You need/want to use the Tangent of the offset angle. So it checks out. I’m a 1st year apprentice I still haven’t done any fancy bends.
@diazaa2 роки тому
@@AngelRomero955ok but what was your question about marking at .57? I have alot of experience (10+yrs) measuring for, routing and bending hydraulic tubing.
@Bapuji42Рік тому
@@AngelRomero955 Huh? The distance between marks is 1/sin(angle) times the offset rise.
@jarrisyed83723 роки тому
hey viewed by me :D
@juancarlosarayamanriquez28503 роки тому
Si hubiera subtitulado español sinvirioa
@patricktelfort4 роки тому
What video is This from?
@passionateengineer044 роки тому
For conduit bending
@patricktelfort4 роки тому
The title of the actual video
@passionateengineer044 роки тому
@@patricktelfort Multiplier method of offset bend
@jondyer47534 роки тому
PASSIONATE ENGINEER Good video
@alen22832 роки тому
Its time to move on kopex like rest of the world!!
@FuquarProductions9 місяців тому
"pick a spot, bend it... then pick another spot, bent it... then you have nothing you're looking for. Thanks for not actually explaining what the multiplier is and how you find it.
@akurukyo62172 роки тому
You probably forgot to show the 1st and 2nd step which is ; preparing the necessary materials,tools,and equipment. And wearing ppe