Most Practical ESP32-CAM? Built-in Programmer, OLED, Antenna and Project Examples

День тому

For Project Examples with Code and Instructions, visit ► RandomNerdTutorials.com/ttgo-...
Buy the TTGO T-Journal for ~$12 ► MakerAdvisor.com/tools/ttgo-t...
Getting started guide for the TTGO T-Journal ESP32 Camera Development Board. The TTGO T-Journal features an OV2640 camera, an OLED display, several GPIOs to connect peripherals and a built-in programmer, which makes it easy to upload code. The examples provided use Arduino IDE.
Read an in-depth review of "TTGO T-Journal ESP32 Camera Development Board" on Maker Advisor: MakerAdvisor.com/ttgo-t-journ...
ESP32 I2C Communication: Set Pins, Multiple Bus Interfaces and Peripherals (Arduino IDE): RandomNerdTutorials.com/esp32...
Like my page on Facebook:
/ randomnerdtutorials
Follow me on twitter:
/ ruisantosdotme
Subscribe for more projects like this!
bit.ly/subscribeRNT
#ESP32 #IoT #Arduino

КОМЕНТАРІ: 23

@RuiSantosdotme 4 роки тому

For Project Examples (Video Streaming Web Server, Taking Photos, Camera Web Server, Display Text in OLED Display) with Code and Instructions, visit our blog ► RandomNerdTutorials.com/ttgo-t-journal-esp32-camera-getting-started/ Grab the TTGO T-Journal ESP32-Camera for ~$12 - $14 ► MakerAdvisor.com/tools/ttgo-t-journal-esp32-camera/

@ajayamaharana339 4 роки тому

Sir, how many distance from ttgo it can see to able.

@supperka2 4 роки тому

is possible to use led flash? what is on the board ?

@niconico-cg6mp 4 роки тому

Excelent video , how to install framework micropython with ttgo?

@gr7480 4 роки тому

Hola Rui, muchas gracias por este video. Chao

@dlsspy 4 роки тому

Are you able to run the board off the battery supply? I've got two of these, and when I feed them ~4.2V via this port, they take about 0.05A and never fully boot. Both seem to work fine off of USB.

@dlsspy 4 роки тому

Small update: I'm able to get it to run from a battery if I press reset. Just plugging in a battery doesn't seem to complete a boot.

@EagleEyeShooting 3 роки тому

Hello Rui, I cannot get this camera to program, though I can see it in the serial monitor load up the example AP sketch, Im unable to upload any sketch. It will just have the connecting.....______..... and never go through. Any help will be much appreciated. Is thier a IO that needs to grn low?

@mellee3436 2 роки тому

Gpio0. Ground, reset, upload, unground, reset..

@yahnsolo 3 роки тому

dont need to use those FTDI adapters (almost all of them around are fake and wont work on w10), just use an arduino through it´s usb converter. Set the Arduino on reset state (RST to GND), and use the pins RX and TX (D0 and D1) to connect to the ESP32 cam RX TX pins. You will then be able to program it (with GP0 to GND on the ESP on start). Use the Arduino's COM port on the IDE or any other programmer

@pruthuvinavod7035 4 роки тому

I have to make a request to you. Teach them heart rate sensor reading an upload it to webpage

@GaryMcKinnonUFO 2 роки тому

Also, no need to reposition that TINY resistor on the CAM for an external antenna.

@saravananvenkatachalam1077 22 дні тому

TTGO T-Journal Doesn't has any on-board antenna, So it doesn't require any config.

@shakerileiwat4341 4 роки тому

Great ☺

@RuiSantosdotme 4 роки тому

Thanks!

@matthiasBdot 4 роки тому

You only need the ftdi once

@thitiwatsingsrikarn8190 4 роки тому

can you help me use esp8266 scanwifi and post data to mysql ? tech me please

@RuiSantosdotme 4 роки тому

Have you tried this code example? randomnerdtutorials.com/esp32-esp8266-mysql-database-php/

@thitiwatsingsrikarn8190 4 роки тому

@@RuiSantosdotme I do but can't Would you mind helping me out?

@yupingliao4078 4 роки тому

good

@RuiSantosdotme 4 роки тому

Thanks!

@CiedJacaba 4 роки тому

eps32-cam ai-thinker has more gpio pins

@The_Unobtainium 3 роки тому

3:04 - in my opinion this is complete bullshit because most likely 90% on people here alread have ft TTL-USB converter for numerous reasons/projects. You neda one FT and you can 1000 ESP32CAMs:)