What an interesting place to find a broken angle grinder.

Что за мода, взять старенький интрумент измазать глиной и потом реставрировать.

А я когда в лес за УШМками хожу потом их всегда в стиральной машине мою )

@ BL Restoration... Just a safety item for you... Never lubricate any part of the commutator or armature with any petroleum based lubricants. These parts do not contact each-other when powered up. If the grease gets too hot it will ignite when it comes into contact with the operating carbon brushes. If you feel you need to seal this area, spray silicon is the best option then let it dry. Never use petroleum based products in this area. They also attract dust and dirt which will eventually damage the equipment you just restored. Other than that suggestion, great job. Keep it up.

I am sure lubrication should never come between the two pieces of the actual motor plus lots of parts should have been replaced not just cleaned .. that thing will fizzle very quickly if it will ever work right at all

ive never felt bad for an angle grinder before that poor thing looked absolutely destroyed, glad you could give it a second life

Surprised that you didn’t have an ultrasonic toothbrush with different brush heads to clean various layers and parts. Thanks for sharing this video. You have amazing talent. Cheers,

Realmente creo que hay gente , que le sobra el dinero... Antes de tirarlo se desmonta , se limpia ,se pinta, se engrasa ...y ya está !!!. Saludos desde Barcelona Catalonia

Great job. But I advise you to check the gearbox again. 17:12 grease the gear that is not secured by the retaining ring. 17:17 close the gearbox without the gear stopper. I hope you noticed and installed it 😀👍👍👍

Скажите пожалуйста если якорь и стартор не сгорел то зачем её кто то бы выкинул?))

For sunbaked plastic, you want to get every last bit of the sunbaked layer away before you paint it. It's no longer a part of the main body so it'll flake away under the paint. Secondly, don't paint plastic without a primer and don't go heavy on the first coat - or any coat. The paint chemicals react with the plastics and cause gases to rise below the surface which cause the surface to bubble, never the mind all the paint running as it dries.

B L RESTORATION IS THE EMPIRE POWER TOOLS RESTORATION CHANNEL "great salute sir"

Постановочные реставрации, такое себе...

Excellent Restoration!!! 👍😎👍😎👍😎👍

A new joint in the channel from Iraq and I love your work ،، مشترك جديد في القناة وأحببت اعمالك الرائعة

I enjoyed watching your video, many thanks. One question; when you use sandpaper on the laminations - don't you then short them out and cause more eddy currents - and hence more heating and lower efficiency of the motor? I know it is a big NO-NO to use sandpaper on the laminations of a transformer.

OTIMA RESTAURAÇÃO FICOU NOVA PARABENS!!

А я по лесу шёл и нашел УАЗ с документами формлены на меня

Salute your hard work amazing job.

É maravilhoso ! Ficou linda !

Excelente trabalho Adóro esses episódios.

Sempre vou deixa meu Lake pra fortalecer o canal 👌👌

My mechanic is the restoration channel to see some serious workmanship

I think the finds are a set up. They turn up in the most unusual places, like someone's just put them there? P.S love the blade tack welded on the wrong way round. I'm coughing now " bullshit"..

You put the fan in the motor opposite.Check 4:28 and 15:00 but great job totally!

Хоть бы прозвонил там что-то....для виду ))

Trabalho maravilhoso tmj.

That lubricant.. Satisfying❤️

Good restoration

Excellent work, it was beautiful. I had the impression that the induced rotor is burnt out because at 11:45 it is possible to see some sections of the damaged collector. Congrats.

Parabéns 👏👏👏👏

Muito bom seu restauro nota.10.

Обмотка статора не позеленевшая, видать пару недель макс пролежала в котловане)

Emeğine sağlık çok güzel oldu

The place you "found" it was so cool

Amazing restoration. I also did a grinder restoration on my channel. Thank You very much for your nice work.

MUITO BOA A RESTAURAÇAO .ABRAÇO DO BRASIL...

Siemmens never finish. Good machine

Ficou ótimo, nota 10.

Another truly amazing restoration.💚💚💚

Was there some test you did....maybe off screen....that let you know that the armature was still good? Ida bet money that it had burned through some place and that was why it had so much blackening. Thoughts?

I used to repair tools for a construction company and never worked on one of these however, from what I saw in video that was just like the Milwaukee Brand

The rpms look a bit slow. I think the electric motor is not working properly

Wonderful.

WONDERFUL !!!!

Amezing

БОЛГАРКА УЖЕ БЫЛА ИСПРАВНА. ХАЛТУРА.

I wonder if safety gloves are required for disassembling or assembling only, not washing or restoring?

Good clean

Well it obviously didn't work at full rpm when you tested it, that's why you test the motor before you do anything else.

Was. ...dune. Like. The. Work. U. Do. I. Good. Never. Do. So. Nice ☺️. Lee

What did you put on the rotor? I'm rebuilding my dad's Black & Decker 679 drill. It's at least 60 years old. Do I need to apply the same lubricant to it's rotor?

Bị hỏng rotor rồi a, kho lắp phe vào bánh răng sao a 😂

Почему не потерялся диск без зажимной гайки.

غير صيني. 😎 خوما العربي مثل الثور ياكل ويسرجن 👌

18:30 also use this SOFTSTART. I have it on an electric mower from Makita - with a commutator motor, in a scarifier. Is perfect ;-)

Я один увидел искры в отверстие под ручку? Ламели якоря чернее ночи, якорь в явном КЗ , это не реставрация , а просто промывка и покраска ..

Мамкин реставратор

Тоесть испачкать рабочий инструмент , а потом помыть его - это теперь называется реставрация?

محتوى رااااااائع

Your videos are great! But I wish you would lose the music. Your talent is enough to keep us watching.

muito bom, eu gostei

Absolutely fantastic To the death you gave a life Great work perfect restoration

Please add the working part after repairing. Like cutting some items etc....

O sea que la tiraron cuando todavía andaba?, pregunto porque al motor no le hizo ninguna reparación

We need to first ask this question... how do these get that dirty ?

How many new parts did you have to get? It looked like it had "burnt up." Could you tell what part was the failure? After the restoration, we saw you turn it on, but is it going as fast, as it should? How did you source the parts: just look the model up on the internet and order the new parts?

Nice restoration. Whit what type of grease you lubricated armature and why?

Отверстие под блокировку шпинделя холодной сваркой залепил бы чтоль......

Так вот ты какой всратый реставратор! А ротор ты зачем смазал?

I pray who ever reads this becomes successful in life.

Шурупы подозрительно легко открываются

Штукатурку и отработку явно ты сам сверху намазал! Это уже блеф

So. Yery. Cool 😎

I was expecting that circular to be cleaned up and put back on

рабочии инструмент на свалке... горел так , что корпус и провод целы, даже этикетка сохранилась ... краска из балончика на редуктор ... нууу , товарищи , вы поняли чем пахнет XD

👏👏👏👏👏

Ну прям не болгарка а радуга какая-то😁🤣🤣

Just one minute ago a guy "found" a drill press . Hahaha

👏👏👏👏👏💥

Как-то неубедительно крутиться в конце, обороты маленькие. Хотя если для музея, то пойдёт.

NO ES REPARACIÓN , ES MANTENCION .

This is not a restoration, but a show. Shame.

never find something like this )))))

Begin you restoration at 1:00. Nobody cares where you find the tool. Fake or not. Good job.

Клоун "Дристовратор" представляет кино - "Пошёл за грибами и насобирал грязные рабочие болгарки".

Grandioso muito bem feito, fiz um vídeo muito parecido no meu canal!

Спасибо повеселили. Идиотизм непобедим.

Its fine

The impeller is inverted

He re-used the old wiring!

Какойто он плохой мастер!

How is name the camare is vadeo

Зачем было якорь смазкой мазать? Чтобы на него абразива налипло больше?

What country are you in?

Ты хочешь сказать что она где то валялась фиг знает сколько и стальной редуктор не заржавел?

they restore these old things but why not their own tools🤣

We just goin to act like we didn't notice that sawblade of death was tack welded on when he "found" it?

why you need to lubricate rotor, better do farming and plant sweet potato. the vibration is too much the rotation is not running smoothly

А разметку в поле не нашёл случяйно Куда её там включяли