If you like the video, please introduce it to your friends and social media !

Nice refurbishing project. If you will take the neutral line input and wire it to the other leg of the rocker switch, than the switch will light up when you turn it on... Also, if you want to keep paint from getting under the tape with stencils, first do a light spray with a clear coat of paint. That seals the edges of the tape and it won't allow paint to get under the edges. Thumbs Up!

Огромное спасибо за представленные видео! Действительно ЗОЛОТЫЕ РУКИ! Есть на что посмотреть и над чем задуматься.. 👍

Most restoration UKpostsrs will sandblast, wire brush, nickel plating. But I think sandblast, nickel plating then wire brush is much better. This restoration is perfect! 10/10

as usual the result you achieved is wonderful. your precision makes the difference and it's a pleasure to watch your videos. However, I must make a clarification about the grinder which is not rusty at all but just dirty and slightly oxidised: a good cleaning and a wipe with steel wool would have been sufficient to make it 100% operational.

Videolarınızı izlemek çok keyifli. Diğer projelerinizde olduğu gibi restorasyon işlemlerinde de tam bir profesyonelsiniz. Detaylara verdiğiniz önemi, düzeninizi ve temiz çalışmalarınızı takdir ediyorum.👌🏻👏🏻👏🏻🙌🏻 Tebrikler usta.🙂🙏🏻

Nice renovation project. you do well . You apply stone protection glue and after a few days it will peel off. I have been in the repair business for 25 years. What I usually do is rivet a few rivets, which last until they break

Прекрасная работа! Сервис неправильно перевёл на русский язык название реставрируемого станка. 😂 Это не мясорубка!

Very nice that it was so clean inside. Great results, many more years of use for you in this tool.

Did it need repaired, probably not ... does it now look fantastic, most definitely ... brilliant 👍

Excellent 👌👌👌👌👌👌👌 Very Good Job

Remember kids.... NEVER re-use a grinding wheel that you do not know the history of ! ! ! Beautiful job as always mate = ) Hope you and yours are all safe and well.

The main body paint was fine. Just needed some clear-coat. Ahh it's great like this too. And everything else. Awesome restoration.

Very good indeed and to your usual level of perfection. Well done......

Gosto muito de apreciar os vídeos deste canal, o autor alem de inteligente é muito detalhista e sabe fazer as coisas

Фантастика! Просто прекрасно )

Excelente como siempre. 💪🏻 👍🏻 🇦🇷

Не знаю! Наверно так и помру не узнав для чего он мыл корпус?🤣

Très belle restauration, du beau travail......comme a votre habitude.

Congratiulations, this is a beautifull restoration.👏🙏🙌

Super great restoration 👏👏

así es que se hace un buen trabajo!!!! mil felicitaciones por eso y gracias por el video no fue tiempo perdido.

Amazing work, great finish👍

楽しみにしてました！🎉

ああああぁお客様！！！困りますお客様ぁぁぁぁ！ 勝手に新品以上の修繕をされてしまっては私共困り果ててしまいますう🤣

Amazing video. Thanks!

ベアリングもシャフトもキレイなグラインダーでよかったですね！

Great job 👍

Beautiful job. Shouldn't the frame of that grinder be connected to Earth ground to prevent a shock hazard if one of the internal conductors touches the case?

Perfect restoration keep it up bro

Grossartiger Job!! Exzellent ausgeführt. 👌👍👍👍

It looks great and you did a wonderful job restoring it as well!!!! I enjoyed your video so I gave it a Thumbs Up

Great job. :) Instead of oil use copper grease where the axle and bearing meet. It will last forever and prevent any rust from coming ever again. Btw..I'm a blacksmith and machinist who enjoys your videos very much.

Как всегда великолепно😊

I like that screwdriver set you're using

Amigo muy bueno todo lo que hace me gusta porque esa es mi pasión lo felicito

Que original queda todo lo felicito

Qui abita l'eleganza!!

Во‼️ Давненько не было🤷🏻‍♂️ Булатный лайк мой👍

Excelente tutorial maestro, un trabajo impecable, el detalle elevado al máximo nivel, ni de fábrica salio tan bonito, gracias por compartir sus conocimientos y experiencias, un saludo cordial y por supuesto un merecido like desde Narón (Galicia)👍🤓😜

stunning!

Can't believe that's a genuine New Strong!!!!

Lovely video

Чётко! Красота😍💓

Quite frankly, the best I’ve seen on UKposts yet …. 30.1.24

Very nice

Trabalho de mestre

This is funny to finish by believing that you actually build it. There is a lot of features that I would have liked to see build. Domo Arigato.

Perfeito, nota 10

Looks better than new.

Pero mas que reparar es restaurar, gracias x tu video

Nice job. But let me give you an advise: When you have oval holes, like th e holes in the grind stone housing, you hav to use washers underneeth the screwheads.

Beautiful

One more thing this needs is some perspex shields, can never have enough eye protection.

こんばんは🌙😃❗ 凄いで上手いで良い!😆👍️

perfect

Нож ремонт работы 🙋🏻👍👍🏻👍🏿👍🤣🤣🤣🛠️🔧📹 посмотреть интересно

Thank you for sharing, I always look forward to your videos. What flow rate is your compressor for your sand blaster?

11:27 I was afraid this would happen. Those tapes prefer tearing than being removed. Wouldn't it be easier to etch it with acid?

Super works

Hello, could you give me the site where you buy the profiled aluminum trays and the profiled aluminum bars please. thank you for helping me and answering me. Sincerely serge

Mistrzu! :)

Love your videos, but am surprised that (a) you use an adjustable wrench instead of the right-sized socket, box or combination wrench (much less chance of rounding over nuts) and (b) no penetrating oil on any of the stuck fasteners. But keep up the great videos!!!

It's a good practice to replace old electrical cable with a new one. As the rubber gets, old it tends to break exposing live wire.

Теперь можно и на рояль поставить!

Eveneens terug prima video.En tevens ook aardige reacties.

That's a first I've never seen someone do plating with a battery for the power source

раз у них такие мясорубки - боюсь представить как у них выглядят точило

3:05 This divided housing is interesting.

Super 👍👌

سلام ایده های شما تمام شده قبلا بسیار موارد خواصی آموزش میدادید

Это не мясорубка,а точильный станок.

Трогая руками голый метал знай на твоих руках есть пот который дает 100% окисление метала и краска через время все равно в том месте отойдет!

Вал в идеальном состоянии

when u sandblast it why wash needed?

Grinds my gears that he did not clean off the muck on the outside first.

Суппер🤟

Superbe 👍👍👍👍👏👏👏👏🖐🏽🖐🏽🖐🏽🖐🏽🖐🏽🖐🏽

特別な魅力は、平らなスロットを持つネジです！ 保護透明バイザーを固定するための未使用の場所がありました

No dust extraction. It is extremely dangerous to breathe this dust. You need to attach a vacuum cleaner to the casings.

🔥

Ça va, il y a pire comme état, c'est dommage que l'ancien propriétaire n'ait pas pris plus soin de son outil.

why was not the power cord replaced with a new 3 wire that has a ground in it, hard to come back from electrification , all of your video safety was for most hope this was a over site, your video are great enjoy the very much

なぜプラスネジやめてマイナスネジ使ったのでしょうか？固着した時取りやすいとか？

Точильный станок.тс. но не мясорубка!

Если это мясорубка , то я президент . 👍

♥️👍

moedor ?

👏👍💪🔥

Ремонт Мясорубки 😂 а где Мясорубка ?

В России это называется "Точило"

у меня перевело на русский язык, как ремонт ржавой мясорубки))))

1:21 What tool is that?

Так это ржавая мясорубка, кофемолка, или....?

Ручки то помнят😊

👍👍👍👌🙂

👍👍👍

👍👍👍👍👍👍👍👍👍👍👍👍👍......

Норманый станок был, не надо было ничего и делать, покраска на функционирование не влияет.

И где здесь мясорубка ?