#405

2 роки тому

The first cheap chip supporting 5GHz Wi-Fi is the Realtek RTL8720 and it should be Arduino compatible. But is it any good? And which tricks do we need to know? Or is it better to wait for the new ESP32, which should also support 5GHz Wi-Fi? Let’s test it out! And discover that the manufacturer included a multi-level adventure game, free of charge.
I am a proud Patreon of @GreatScott!, @ElectroBOOM , @Electronoobs , @EEVblog , and others. No Docker, No Microsoft Teams, Zoom
Links:
RTL8720 / BW16 %GHz WiFi : s.click.aliexpress.com/e/_9AV5GR
ESP32 Dev Board : s.click.aliexpress.com/e/_ApGhKT
RTL8722DM www.seeedstudio.com/Ameba-RTL...
BW16 Getting started: www.amebaiot.com/en/amebad-bw...
Autoflash tool (not tested by me): github.com/jojoling/ameba_bw1...
Write-Up of RTL8720 experiences: drive.google.com/file/d/14CX5...
Approximate Library: github.com/davidchatting
BW16 Datasheet: www.futurashop.it/image/catal...
5GHz Smartphone Sniffer (not tested): github.com/FL0WL0W/HumiditySn...
Spectran V6: aaronia-shop.com/products/spe...
The links above usually are affiliate links that support the channel (no additional cost for you).
Supporting Material and Blog Page: www.sensorsiot.org
Github: www.github.com/sensorsiot
My Patreon Page: / andreasspiess
Discord: / discord
If you want to support the channel, please use the links below to start your shopping. No additional charges for you, but I get a commission of your purchases to buy new stuff for the channel
My Amazon.com shop: www.amazon.com/shop/andreassp...
For Banggood bit.ly/2jAQEf4
For AliExpress: bit.ly/2B0yTLL
For Amazon.de: amzn.to/2r0ZCYI
For Amazon UK: amzn.to/2mxBaJf
For ebay.com: ebay.to/2DuYXBp
profile.php?...
/ spiessa
www.instructables.com/member/...
Please do not try to email me. This communication channel is reserved for my primary job
As an Amazon Associate, I earn from qualifying purchases
#no#midroll#ads

КОМЕНТАРІ: 394

@irukard 2 роки тому

Long story short... Yes we will wait for the new ESP32 :)

@AndreasSpiess 2 роки тому

And hope they will do it better...

@brad3378 2 роки тому

Is there an expected release date for the next ESP32?

@comment8767 2 роки тому

The coming war with China will tend to limit exports.

@AndreasSpiess 2 роки тому

I do not have a date

@hero-gl4zy 2 роки тому

@@AndreasSpiess what we need to Design our own Wifi Module microstrep antena with our physical TCP layer programming?

@AdityaMehendale 2 роки тому

Andreas, 2021: "I tend to base my decisions on experience, rather than hope" 15:38 Also Andreas: "I _hope_ this video was (useful or interesting) for you" 15:49 Everyone: In our _experience_ your videos are always (useful and interesting) :)

@AndreasSpiess 2 роки тому

Thank you for your longtime support!

@AdityaMehendale 2 роки тому

@@AndreasSpiess No, thank _YOU_ Dr. Spiess for creating a wealth of accessible and approachable information on RF, IoT and automation on YT, 6 years and running, with your Swiss sobriety and sense of humour.

@johannapfelburg6286 2 роки тому

Hear hear!

@MaxDiscere 2 роки тому

"All devboards that I own, and if you ask my wife there are many of them" 😂😂 I can relate to that

@AndreasSpiess 2 роки тому

Seems to be universal ;-)

@torenarend 2 роки тому

His wife does know how to recognize a dev board. Wish i could relate to that.. ☺

@marcelobenitezabc 2 роки тому

Me too..

@koeiekop1973 2 роки тому

Again I am very Impressed how often you post new and informative videos. Thanks again for enlightening all makers and prevent at least half of all your subscribers getting crazy by all these elaborate tricks before this board works. Can’t wait when espressif will have something similar. Great work and thanks again!

@AndreasSpiess 2 роки тому

Glad you like the content of the channel!

@pasikavecpruhovany7777 2 роки тому

Thanks for the gameplay! Bookmarking this so I can speedrun trough as soon as my package arrives.

@AndreasSpiess 2 роки тому

You just have to go to the last slide (if you do not get it with firmware)...

@la6mp 2 роки тому

I admire your stubborness and patience, for me such ill-documented products are no-goes!

@harisalic2568 2 роки тому

Sometimes you dont have any other option

@AndreasSpiess 2 роки тому

After knowing the "tricks" it is quite easy to work with. Except for the pins ;-) As an engineer you have to have some "stamina", I think. And some say that carrying a Ph.D. shows that you, at least once in your life, had a lot of stubbornness.

@Flamechr 2 роки тому

@@AndreasSpiess especially in the usa. Not only do you need to due alot of work in your field but also navigate safely in the political enviroment when working on your Ph.d

@johncrunk8038 2 роки тому

@@Flamechr Why is getting a Ph.D (post hole digger) so hard?

@stevej420 2 роки тому

Realtek has made bad documentation/products like this for years. If this works out anything like their ethernet/sound chips i suspect that webpage with directions will vanish in a few months, and be replaced by a Taiwanese version. In a while all software you will need to download will be hidden on an ftp in asia that gives 4 K/s downloads. After that it will most likely just stop working in arduino IDE as they release a newer version with the same specs and a slightly different number in the name.

@innomkr 2 роки тому

Thank you for saving me the time to play around with this board!

@AndreasSpiess 2 роки тому

You are welcome!

@riz94107 2 роки тому

I like the humor in this - I have a couple of these boards waiting for me to have enough time to play with them and now, at least, I know what to expect. :). Doesn't seem TOO different than the standard "every chip vendor does their own thing and takes their sweet time realizing that there are standards they should adhere to", but it's good to have had someone so good at explaining hit the road bumps first... Thanks for another great video.

@AndreasSpiess 2 роки тому

You are welcome! I was astonished how many riddles I had to solve. I think it was the most complex start with a new board. For you it should be easyer to start (except the pin numbering). I still forget to push the buttons once in a while. But this can easily be detected and fixed...

@trentbrown3714 2 роки тому

I spent some time with this board a while ago. It took effort but I managed to get it working for my needs which is mostly connect to differing BSSIDs in a mesh network, pass traffic, disconnect, re-connect to a different BSSID and so on. Once I got the caveats figured out it has been fine, but then my needs for this use case are simple.

@dave-in-nj9393 2 роки тому

You, Sir, are a Saint and an asset to the maker community. Your generosity, abilities and patience allow us all to get more out of our hobby than we could do on our own. Thanks.

@AndreasSpiess 2 роки тому

Thank you for your nice words!

@peter.stimpel 2 роки тому

thanks a lot for explaining to me to ignore these boards for the moment - no 5 GHz needed ftm. You are quite effective :)

@AndreasSpiess 2 роки тому

Why do you think I am effective? I thought I was very unproductive with this board ;-)

@peter.stimpel 2 роки тому

aside from jokes: I would love if board manufacturers would establish and follow some basic standards.

@AndreasSpiess 2 роки тому

Agreed. I think that Arduino was very good in this respect. This was probably necessary to be so successful.

@mrichgouda 2 роки тому

Hi Andreas, Interesting video….as always! 😉 Unbelievable that you was able to complete your journey through this documentation-swamp !! Respect! But as said by others here already…. This ill documented boards are a no-go for me…. I’m not afraid of a bit of puzzeling now and then… But this is too much! I’m looking forward to your next video. Keep up the good work Andreas 👍

@AndreasSpiess 2 роки тому

I assume that most of the "puzzling" is done now... At least the last tests were done without a lot of time waste.

@davechatting 2 роки тому

Thanks for the shout out Andreas! I'm very excited to see these new 5Hz modules. I don't have much time to work on the Approximate library at the moment, so would welcome anyone making contributions

@AndreasSpiess 2 роки тому

You are welcome. I got a link from another viewer which already have created one. I left a link in the description (I did not test it yet).

@johnwilson3918 2 роки тому

You have the patience of a Swiss Saint, sir.

@AndreasSpiess 2 роки тому

It was more the curiosity of an engineer, I think ;-)

@jrioublanc 2 роки тому

Thanks for the explanations, you convinced me, I gonna stay away from this part until they write a correct manual and simplify the use of USB ports

@AndreasSpiess 2 роки тому

You are welcome!

@simoncollins6650 2 роки тому

Interesting great insight in to the chip thanks Simon

@AndreasSpiess 2 роки тому

You are welcome!

@jmr 2 роки тому

Thanks for doing the leg work!

@AndreasSpiess 2 роки тому

You are welcome!

@blaing99 2 роки тому

Always an adventure with new tech & translated datasheets!

@AndreasSpiess 2 роки тому

Exactly!

@bitschips 2 роки тому

Good job, really liked your adventure tour! Very educational, thanks for time.

@AndreasSpiess 2 роки тому

Glad you enjoyed it!

@bitschips 2 роки тому

@@AndreasSpiess please could you recommend me an Arduino compatible board with micropyrhon? Thanks!

@AndreasSpiess 2 роки тому

Arduino and Micropython are different things and not at all compatible. Go to the Adafruit homepoage or search for my video about Micropython

@bitschips 2 роки тому

@@AndreasSpiess I Will do, thanks!

@wjn777 2 роки тому

Thanks for the video, you have lots of patience and I enjoyed your humour. I was surprised at yiur conclusion, it's hard to judge this board with so many things unclear like deep sleep

@AndreasSpiess 2 роки тому

After knowing the tricks you can at least use it to reach your 5GHz Wi-Fi. No other chip can do that using the Arduino IDE.

@FredW-yt1ce 2 роки тому

Thank you for another insightful video. What wi-fi spectrum analyzer where you using in the video?

@AndreasSpiess 2 роки тому

A Spectran V6

@ErichHaubrich 2 роки тому

The information you share, and your effort to help us all better understand this technology is fantastic. You are an asset to the world community, my friend. Thank you for what you do. Cheers!

@AndreasSpiess 2 роки тому

Thank you for your kind words!

@hafo821 2 роки тому

Thanks for your opinions before experiencing on my own! :_D

@AndreasSpiess 2 роки тому

You are welcome!

@gregorymccoy6797 2 роки тому

I appreciate you keeping the community informed about this. I'll wait for the time being before getting into the 5Ghz band.

@AndreasSpiess 2 роки тому

Definitively a good decision if you do not need it.

@UnexpectedMaker 2 роки тому

That was quite entertaining... I'm glad you had to go down that rabbit hole, so we now don't have to! Thanks :)

@AndreasSpiess 2 роки тому

You are welcome! I had to chose between a humorous and a rant video ;-)

@Palominostudio 2 роки тому

Hi Andreas, I enjoyed this one, a nice factual review of this piece of equipment. It's an interesting development, as always the stuff is in it's infancy and we have to deal with the infantile behavior of the product. Luckily there's the thing called competition in the market, and that largely forces improvement. At least I am basing my hope on that hypothesis. Realistically, let's assume it's a Beta release. Which is how things work, as it's the outcome of the multiplayer game involving the sales and marketing team versus the research and development team. Largely that works, on balance. But it's messy in the beginning. So, we watch this space. Kind regards, South Africa

@AndreasSpiess 2 роки тому

I agree. We will see if they watch this channel ;-)

@ivancho523 2 роки тому

awesome, thanks a lot for information

@AndreasSpiess 2 роки тому

You are welcome!

@sikedipuuhja7376 2 роки тому

Andreas, kudos for completing all levels! with regards to the idea of a uC with low power to support the 5GHz band… well. this is i guess a niche thing. the range is subpar compared to 2.4GHz. sure it can help using wifi when you have continuous analogue 2.4GHz noise in the area. but usually small uCs don’t use the channels at a high speed, so even in a crowded wifi environment they’d be just fine. yes, the AP can be also limiting factor, how many connected clients it is able to handle. also the power constrained BLE is a bit lackluster. one extra question: what 5Ghz standard did you use? 802.11a or 802.11n?

@AndreasSpiess 2 роки тому

I do not know (I am no specialist and did not care)...

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I introduce how to develop IOT using this. You can get information by visiting.

@zencow 2 роки тому

It looks like you found part of your translation by recognizing patterns in pin naming, but I'll share this bit that I recognized: The Pxnn notation (e.g. "PA1", "PB3", etc) is one I've seen before on PIC microcontrollers and others. It refers to "Port A" and "Port B" (and so on), with pin number indexes, often 0 thru 7 or 15, depending on how many pins per port their device offers. They can sometimes be used in parallel, so you can work with a byte sent to the Port instead of needing to set single bits for each pin separately. Very handy for bit-banging protocols and changing outputs or reading inputs in parallel.

@AndreasSpiess 2 роки тому

You are right. This is naming convention is also used internally in the Arduinos and needed of you want to do bitbanging as you described.

@alessandrogalasso927 2 роки тому

Hi Sir, I saw your video about capacitive moisture sensor. So I would like to ask to you, what are typical values of a dry soil that need to be watered and wet soil that is ok for the plant? Let me know! ( I had a classic sensor but now I'm waiting for the capacitive one)

@AndreasSpiess 2 роки тому

Unfortunately I do not remember the values and I also did not find any information about the accuracy of such measurements.

@chemarytech 2 роки тому

I recently tested ESP32-C3S and nRF52833, both supporting BLE long range with 7dBm and 8dBm, and even with this power output the range was almost double than a Tile Mate and the penetration of walls was quite superiors to standard BLE

@AndreasSpiess 2 роки тому

Good to know. Thank you!

@jarchdm 2 роки тому

i couldn't even get the blue pill board to load so I'm giving this one a wide berth. Thank you.

@AndreasSpiess 2 роки тому

Now I learned a new word: Berth ;-)

@jarchdm 2 роки тому

@@AndreasSpiess Literally, give a wide berth is a phrase that dates back to the seventeenth century meaning to allow a large space between ships to enable optimum safety and maneuverability. Today, there is also a figurative meaning to the phrase give a wide berth, meaning to steer clear of someone or something, to keep your distance from someone

@dimmoos757 2 роки тому

I will wait for 5Ghz esp32! Thanks for video.

@AndreasSpiess 2 роки тому

Good choice!

@xDR1TeK 2 роки тому

Wow it needed a lof of tricks. I would have pulled a lot of hair in the process. Had similar issue with the riscV esp32 while using eclipse.

@AndreasSpiess 2 роки тому

Fortunately, I do not have a lot of hairs left to pull ;-) Eclipse was also a nightmare for me a few years ago :-( I never touched it since.

@omnipresence8089 Рік тому

Hey Andreas, nice vid. Which example code did you use to get a 5ghz connection? All of my current examples only use the 2.4ghz band

@AndreasSpiess Рік тому

I do not remember :-(

@omnipresence8089 Рік тому

@@AndreasSpiess no worries. I found out that you just have to define a 5ghz wifi channel in the setup function in the .ino file. Example: channel = "52"

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.

@DuncSargentsKarstValleyRR 2 роки тому

Thanks for that!

@AndreasSpiess 2 роки тому

My pleasure!

@DLSDKING 2 роки тому

Cool board. Good competition for espressif in DIY wireless mcu market. Should expect a refined library and documentation from them.

@AndreasSpiess 2 роки тому

I am not sure they did the Arduino support themselves. At least the boards repository belongs to a US guy...

@DLSDKING 2 роки тому

@@AndreasSpiess The implementation looked like a pet project between several developers without a common consensus. I hope them to work on that. I appreciate the effort of them to bring arduino support for rtl product programming. I had been using rtl chipsets in several products(desktop motherboards, wifi cameras, tablet pc) yet i never had the feasibility to develop an application of my own with their chipsets. This is a start for them and i thank you andreas for letting us know.

@rosenwang6618 Рік тому

Ohh, good share. I bought 2pcs from original manufacturer Ai-Thinker.

@AndreasSpiess Рік тому

:-)

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.

@scottyanke655 2 роки тому

I remember trying to use RealTek chips a few years ago. I finally gave up because of the same riddles you ran into. I ended up tossing them, because they just weren't worth the time spent on them.

@AndreasSpiess 2 роки тому

Thank you for sharing your experience. I do not know if the chip is good. At least it is the only we can use on 5GHz. But the documentation needs an update.

@bromnader5196 2 роки тому

Hi Andreas - I really enjoy your videos and learn a lot from them. I also love your sense of humour, like in this video about how the engineers made sure that nobody but the most sacrificial could use their product. LOL Please keep these coming. My interest would be using MCUs and sensors in general aviation - how to build AoA indicators, gyros, accelerometers and other instruments that costs thousands of dollars if purchased from the big boys. In your video comparing STM32 to ESP32, you ran a benchmark to compare the speeds. The benchmark had one or two lines of the sort x = CONSTANTA + CONSTANTB; x = CONSTANTA * CONSTANTB; You realize that the C compiler actually performs the addition/ multiplication in compile time and this just becomes a literal assignment at execution, without the arithmetic operation?

@AndreasSpiess 2 роки тому

I do no more remember my benchmark. When I created it I was very new and did not think about the influence of the compiler. You are most probably right with your statement. About aviation: AFAIK a lot of the cost is due to testing and regulations. So material cost is probably also low for the big guys...

@drmocm 2 роки тому

A very nice description of the RTL8720 experience.

@drmocm 2 роки тому

I am sorry that I did not realize my comment in the Mailbag video about how to get rid of the firmware did get deleted that would probably have saved you some time.

@drmocm 2 роки тому

It seems youtube deletes every comment mentioning the python script and/or the link to the troubleshooting guide for the board.

@AndreasSpiess 2 роки тому

They seem to delete all comments with links. Also mine :-(

@AndreasSpiess 2 роки тому

And thank you that you tried to help me…

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I introduce how to develop IOT using this. You can get information by visiting.

@csbluechip 2 роки тому

Woooww! I thought there was going to be trouble when I saw "RTL", but this is a whole new level of clusterfunkery! Thank you for suffering the pain so I don't have to :)

@marcelobenitezabc 2 роки тому

They will be VERY happy with this video...

@AndreasSpiess 2 роки тому

The problems are not too hard to solve for them, I think…

@McTroyd 2 роки тому

I wonder if it would be worth just getting the module, and using a plain breakout board? Should help reduce some of the pin confusion! You already need the RS-232 adapter, and 3.3v could be done without the inefficient regulator. 👍

@AndreasSpiess 2 роки тому

Creating a proper board for sure is a good idea. Particularly if you need additional components.

@mcconkeyb 2 роки тому

LOL, I thought that you had been doing this long enough to know that every new chip requires days and days of "free game play" to get them working. 😃 I've been doing this since the 1980"s and I've never seen a new chip that was easy to get working. Actually this seems easier than most new chips. Good tutorial, I'm sure this will save several others hours of banging their head on the table in front of their development stations.

@houserental5424 2 роки тому

It’s not a new chip, the Realtek Ameba came out the same time as the ESP8266, it’s always been a mess with bad docs

@AndreasSpiess 2 роки тому

Here not the chip was the problem. They created a lot of confusion without need. After knowing the "tricks" it was quite easy. This is why I thought they made it on purpose ;-)

@marcelobenitezabc 2 роки тому

Espressif's NEARLY work out of the box..

@sethhall5862 2 роки тому

@Milan Velky Bye bye... no great loss! Civility has its place, and is not over-rated!

@Sovvyy 2 роки тому

@Milan Velky Holy projection. Go get some fresh air, come back and re-read your comment... then feel free to google bulverism.

@matthewfelgate 2 роки тому

Thanks for making this video because I'm excited there are 5GHz Arduinos coming out. Any more boards out since this video?

@AndreasSpiess 2 роки тому

Not that I know of

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I introduce how to develop IOT using this. You can get information by visiting.

@MagnusWedmark 2 роки тому

Would be nice to see how this chip actually performs against the ESP32 on some different calculation performance test. Or has this already been done on your channel? ESP32 vs. ARM.

@AndreasSpiess 2 роки тому

I did this with STM chips. The M4 was quite fast, and this one has even a higher clock rate...

@Giblet535 Рік тому

Thanks for sticking with it. That is a level of stubbornness that I no longer have. Those are some headaches, true, but about the same as programming a typical ESP8266 "Smart" device w/ FTDI to change its functionality. And hey, at least the RTL has a PROGRAM and RESET switch to make that part easy. I still would have thrown it away.

@AndreasSpiess Рік тому

:-)

@typxxilps 2 роки тому

Didn't you get a pi zero 2W ? I had thought you were one of the first ones who got that pico back in spring this year.

@AndreasSpiess 2 роки тому

I was not nice with the pi foundation when the Pi4 came out. And I was not nice with them when the Pico came out. No wonder I am not on their list…

@aspuzling 2 роки тому

What is the difference between 5 and 2.4ghz when it comes to power consumption? How much power does it take to find the AP, connect and send an http packet?

@Rizon1985 2 роки тому

5GHz obviously uses more power. It has worse range and experiences more problems from objects between sender and receiver so it needs to boost more. It also has to process a lot more data and over more multiple channels at once so it needs to process more and more complex data. Only once the production process upgrades in 2.4GHz chips would stop advancing while it continues for 5GHz chips, could the gap in worse power characteristics become smaller and maybe ever overcome it. But that doesn't matter because you use 5GHz when you need to push that much data. You don't use 2.4GHz either when your data only needs the 433MHz band.

@AndreasSpiess 2 роки тому

I did not check how long it took to connect. But I felt it took longer than an ESP8266 or an ESP32. But I did not do any optimization (e.g. fixed IP address)

@sikedipuuhja7376 2 роки тому

@@AndreasSpiess wireless stations do not set their operating channels, as you only specify the band where it will scan for a certain SSID to connect. with 2.4GHz we have just a handful of channels, whereas with 5GHz we have a lot more, especially if you don't restrict the channel plan based on the location to the permitted ones only. now during scanning the station will listen on each channel for a certain amount of time in order to catch the SSID broadcast, which by default occurs every 200ms. to perform a full scan in a band will take more time in 5GHz than in 2.4GHz. once connected, the DHCP DORA process is just 2 RTTs, where DHCP client on the station sends a Discover, the dhcp server (on or behind the AP) sends back an Offer, then STA will send a Request, and the server will reply with and Acknowledge message. this DORA process takes normally a few (20-80) extra milliseconds to complete. Also the connection process is taking place at the lowest possible data rate, as the SSID is always broadcasted on the so called 'basic rate', which is 1Mbps @ 2.4GHz, and 6Mbps on 5GHz, so everyone in range can know about the AP itself. specifying a "scan list" or restricting the available channels to a certain region (which one should do anyway) can speed up the process, as the STA does not need to scan all available channels. not sure though whether these knobs are exposed in the uC wifi libraries.

@sikedipuuhja7376 2 роки тому

@@Rizon1985 yup, there were advancements, but i have reasonable doubt that the uC in the question doesn't support 802.11ac or ax (would not make any sense by any means), so you are left with 802.11a/g/n which have their equivalent counterpart also on 2.4GHz. no MU-MIMO of any kind is available. also i'm quite confident the wifi on the uC doesn't support MIMO at all (why would it?). in most cases you only want your micro to submit data on a higher data rate to either save on transmission power by 'talking for less time' or save AP airtime to allow more stations to utilise the available spectrum. since 802.11 WiFi uses CSMA/CA for default media access control - which is a pretty lousy way if your think about it - the probability you run into collision/interference rises exponentially with the number of stations increasing and the average length of time a station is accessing the spectrum. in addition to this 802.11 is half duplex, so each time a station transmits, there will be a wireless acknowledgement from the AP, so airtime is consumed quite quickly. it would be worthwhile to see what data rate such a micro will use. my 8266s are at 48Mbps when the RSSI is OK (above -80). sure, if someone intends to use battery powered solutions, the high data rates will take their toll.

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.

@cassiecarstens5184 2 роки тому

Your question (May 2021) "Why should i do it" The pins on power FETS etc. is about 1.1mm flat side and .5mm side view. You must have felt the the resistance when you push in a FET etc acrose 3 adjacent rows of breadboard tracks. It is a lot easier when all 3 pins goes into the same row. (sideways) Also consider the contact surface. So, i just suggested bending the legs 90 degrees before pussing it in. Kand regards, Cassie Carstens

@AndreasSpiess 2 роки тому

You are right. I adopted this method and if is excellent!

@cassiecarstens5184 2 роки тому

@@AndreasSpiess Good! Someone (JP Spies) shared this with me about 40 years ago. So, I have no claim to this. But, PLEASE share it. You and Adel Kassah is my IOT teachers. Thanks!

@jamesgoacher1606 2 роки тому

Wonderful, I have to commend your perseverance and hope the tongue stuck very firmly in your cheek has not been injured to greatly. I too have had to work out how to use equipment from minimal, none, mis;eading and plain wrong information in the past. Fortunately that was some time ago and my head worked better then. Now I rely upon you and similar to have an interesting time on my behalf, Thank You. I think the smiley for a very big grin is :-D have two :-D

@AndreasSpiess 2 роки тому

Glad you liked the video. I when I started to see it as a game I also had some fun ;-)

@XanCraft21 2 роки тому

This video was very helpful. I believe this new technology just came out this year and is still in development. I hope that the manufacture makes versions that come completely blank so you don’t have to erase the current firmware before a custom code will run in the future.

@AndreasSpiess 2 роки тому

I read that some of the boards already come without firmware...

@XanCraft21 2 роки тому

@@AndreasSpiess may i ask if you know how rare they are?

@AndreasSpiess 2 роки тому

You do not see this B&T logo

@XanCraft21 2 роки тому

@@AndreasSpiess ok. Thank you for your help.

@XanCraft21 2 роки тому

@@AndreasSpiess i would like to ask for more help on this subject. I got this controller and i have the same problem with the built-in firmware making the code not run. The help website is no use and your video doesn’t fully cover the part with the firmware. This is the only video that exists in the world for this topic. There is no way i can seem to program the device. I tried downloading a recommended flash tool on the help website, and i need more stuff for it to even run. Do you know any way i can erase the memory chip without the need to download anything or replace the flash chip with an empty one? Thank you for any help you can give me.

@XdewGaming 2 роки тому

You CAN use the core 0 on the ESP32 using tasks. Also the original chip is the ESP8266 not the newer ESP32. This chip seems fine for 5GHz tho because even the newest ESP32-C6 has wifi 6(802.11ax) but only 2.4GHz.

@AndreasSpiess 2 роки тому

You are right with core 0 of the ESP32 (I made videos about it).

@zyghom 2 роки тому

Hi Andreas, I admire your patience. BTW this board and the software reminds me the times of 1990 when we spent days on configuring ppp connection on Linux to get connected to the internet! Unbelievable crap developers! Competition will eat them alive

@AndreasSpiess 2 роки тому

I also remember the 1990 and networking, but on Windows. Back then things were new. This chip is not new and it could have been done better. However I think the engineer was good, but, as a lot of us, hated to document...

@zyghom 2 роки тому

@@AndreasSpiess agree, but WRONG document is worse than NONE ;-)

@marcelobenitezabc 2 роки тому

LOL...

@PriyankBolia 2 роки тому

For presence detection, I will simply use home assistant. Not worth the time to simplify cost by using a 5G wifi chip. ESP8266/32 or the Tuya Chips works well.

@AndreasSpiess 2 роки тому

You are right. You can use other sensors for presence detections.

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I introduce how to develop IOT using this. You can get information by visiting.

@PhG1961 2 роки тому

A remarkable product, overviewed in a remarkable video with remarkable comments. I guess that's why we are all here for... ;-)

@AndreasSpiess 2 роки тому

I had several choices on how to present it. Humor was the easiest one because I do not like rant videos...

@jorgmani6889 Рік тому

Sali Andreas, eine Frage: was braucht es um einen WLAN game controller pcb zu entwickeln? ich möchte ein Lenkrad entwickeln für Online racing habe aber absolut keine Elektronik erfahrung.

@AndreasSpiess Рік тому

Ein Produkt zu entwickeln ist extrem anspruchsvoll. Ich kann dir nur taten, nicht damit zu beginnen.

@scitor 2 роки тому

Little do people know but in most parts of the world (non-US) the 2.4GHz band has actually 4 usable non-overlapping channels, like seen in your video at 3:11 with channel 1, 5, 9 and 13. Just because most firmwares are set to US defaults channel 13 is almost never used ... shame .. great video anyway! thanks for the laughs :D

@AndreasSpiess 2 роки тому

Thank you for your info. I am only a Wi-Fi user and therefore was not aware of this fact.

@nkronert 2 роки тому

When the wife starts noticing how many dev boards you have, you have too many ☺️. Or maybe she's turning into a maker? 😱

@AndreasSpiess 2 роки тому

She is more in "repairing humans" ;-)

@kevinshumaker3753 2 роки тому

And NEVER tell her what the boards REALLY cost. NEVER!!!

@reppad 2 роки тому

There is a simpler way to override the default AT firmware : Just connect a serial terminal on AT port - the one available throught the onboard USB port without any additionnal wiring - at 38400 bauds then sends the command "ATSC=0" to switch to OTA1 image. Tadaaa, the module can now be flashed with arduino, tested and approved (some Aliexpress sellers put this tip on the product page)

@AndreasSpiess 2 роки тому

Thank you for the tip. Very simple!

@nu77byte49 9 місяців тому

@@AndreasSpiess The above dosnt seem to work for me :(

@nu77byte49 9 місяців тому

@@AndreasSpiess on a side note what would be the best way to convert a hall sensor output to be accepted in a speedo that wants a reed switch output. I want to keep my original speedo sensor

@donpalmera 2 роки тому

Still watching the video... but I seem to remember that some big exploits were found in Realteks wifi stuff recently.

@AndreasSpiess 2 роки тому

Maybe you post if here if you find something.

@olafschermann1592 2 роки тому

Waited soooo long for 5Ghz Arduinos. Can’t wait to turn of my 2.4 wifi at home. But it should be flawless. Hope for the next ESP32.

@AndreasSpiess 2 роки тому

After knowing teh tricks it was not too complicated to use them.

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I introduce how to develop IOT using this. You can get information by visiting.

@josecampino7476 2 роки тому

"Luckily no explosion" I wouldn't stir the thing that much, just in case :-)

@AndreasSpiess 2 роки тому

:-))

@xDR1TeK 2 роки тому

I am still hesitant to use a function purposed module like wifi to have GPIOs controlled by the wifi module itself. I prefer to shift that control over to another controller. I might be wrong to think so, but I prefer to split functionality.

@AndreasSpiess 2 роки тому

On one hand it adds more parts. On the other hand you do not have to deal with wifi. A disadvantage for me would be that I have to create my PCB or buy this expensive Arduino boards.

@jeremiahbullfrog9288 5 місяців тому

What is the spectrum analyzer software? What radio does it work with?

@AndreasSpiess 5 місяців тому

The link to the spectrum analyzer is in the video description

@jeremiahbullfrog9288 4 місяці тому

@@AndreasSpiess Thank you

@chuxxsss 2 роки тому

Andreas you sold me when you said multilevel game mate.

@AndreasSpiess 2 роки тому

I thought is is a good way of describing what I felt ;-)

@johnlaurencepoole6408 2 роки тому

For those new to this area, the Spectran V6 looks to cost anywhere from EUR 3,498 to EUR 9,998. Plus antenna in the US$200-$400 range.

@AndreasSpiess 2 роки тому

True. It was granted to the channel from the CEO of the supplier (a viewer of this channel) in order to help us understanding signals better.

@szabolcspolgar4223 2 роки тому

What you need is : rtl-sdr

@IamTheHolypumpkin 2 роки тому

I love 5 GHz WiFi. Only my sprawling Ethernet network is even better. If I wouldn't have some legacy devices which only support 2.4 GHz I would turn off 2.4 GHz completely. Also my Mesh-Wifi has very little configuration, so I can't disable 2.4 GHz anyway.

@AndreasSpiess 2 роки тому

I have mixed feelings about 5GHz because it often does not have a good connection in my house. Then 2.4GHz still is better. Bu, as you, I try to offload the 2.4GHz band as much as possible.

@marcelobenitezabc 2 роки тому

ESPRESSIF has been kicking xxx since 2014... I deeply love Teo Swee Anne.. They have 'la vaca atada' for the next 10 years..

@AndreasSpiess 2 роки тому

I agree that Espressif is an impressive story. We will see how they proceed with the Maker support in the future...

@waynekeenansvideos 2 роки тому

It would be easier to use the SWD pins to program the M4. I bet 2 of those NC pins are the SWD pins for the M0

@AndreasSpiess 2 роки тому

I am not sure because the Module only has 16 pins and I do not see how they would connect it directly to the chip inside the module.

@waynekeenansvideos 2 роки тому

@@AndreasSpiess Looking a bit more I can't actually see where an M0 exists in the module, the RTL8720 only specifies 1 CPU on the datasheet and there's only a single heatsink pad.

@waynekeenansvideos 2 роки тому

Not that it really matters, gonna pass on this one.

@krukhlis 2 роки тому

Well, I've got an idea for you for the next video. Comparison: ESP32 vs this BW16 from the performance, ADC/DAC precision and speed perspectives, power consumption, etc. 😉

@AndreasSpiess 2 роки тому

I have no such plans for the moment. Reading the comments the interest for this chip seems not to be that big.

@pawe3554 2 роки тому

For me 2MB of memory and no straight forward programming method among other things is hint that they probably intend it to be somewhat "easy to use" component in larger applications that will provide not only 5GHz Wi-Fi but also will allow diagnostics and recovery of parent board even in case of catastrophic faliure

@AndreasSpiess 2 роки тому

Looking at the firmware with the AT commands I would assume it was designed as a daughter board for other computers in need for a 5GHz connection. Seeeds uses it in one of their devices like that (the main processor is an SAMD51).

@olafschermann1592 2 роки тому

Any idea if the nordic nrf52 supports BLE long range?

@AndreasSpiess 2 роки тому

I did not look into those chips. It is still on my to-do list

@VolkerKtnbch 2 роки тому

Danke!

@AndreasSpiess 2 роки тому

Bitte, gern geschehen!

@jamess1787 2 роки тому

Oh dear. Let's wait.

@AndreasSpiess 2 роки тому

If you can: A good idea...

@IoTProgramming Місяць тому

I enjoyed it. I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.

@AndreasSpiess Місяць тому

Thanks for the info. I focus on the Arduino IDE on this channel :-(

@thumalamanish2320 2 роки тому

Hi could you please help me find the documentation for this chip. I've tried finding it online but no luck.

@AndreasSpiess 2 роки тому

Did you try the links in the video description?

@SteveWrightNZ 2 роки тому

Well done

@AndreasSpiess 2 роки тому

Thank you!

@taraqiu9455 2 роки тому

BW16 module is our another B&T brand product.

@taraqiu9455 2 роки тому

docs.ai-thinker.com/en/rtl87xx BW12 module specification: docs.ai-thinker.com/_media/rtl8710/hardware/bw12_datasheet_en.pdf BW14 Module Product Specification: docs.ai-thinker.com/_media/rtl8710/hardware/bw14_datasheet_en.pdf BW15 Module Product Specification: docs.ai-thinker.com/_media/rtl8710/docs/bw15_datasheet_en.pdf BW16 Module Product Specification: docs.ai-thinker.com/_media/rtl8710/hardware/bw16_product_specification_en.pdf BW16 development board schematic diagram: docs.ai-thinker.com/_media/rtl00_bw12_bw16_bw19%E5%BC%80%E5%8F%91%E6%9D%BF%E5%8E%9F%E7%90%86%E5%9B%BE-v1.0.pdf BW16 network configuration tool: docs.ai-thinker.com/_media/rtl8710/docs/simpleconfigwizard_v115.zip docs.ai-thinker.com/_media/rtl8710/docs/wificonfig_v2.1.6_20190529.apk.zip FAQ： docs.ai-thinker.com/_media/rtl8710/docs/rtl8720d%E5%B8%B8%E8%A7%81%E9%97%AE%E9%A2%98-20190604.pdf Module certificate：docs.ai-thinker.com/rtl87xx/certificate

@mattytrentini 2 роки тому

That board design does seem to be making things confusing. However, the RTL8722DM chip itself is *very* promising; obviously the dual-band wifi is compelling but so too are the cores (Cortex M33 and M23), the generous ram/flash and the large number of peripherals and GPIO (up to 55). The Seeed IoT and Mini boards look to be much better options to explore the features - I remain hopeful it's going to be a useful chip!

@AndreasSpiess 2 роки тому

I agree about the RTL8722. But I hope they will get their documentation up-to date. Do you know if we can use the second core?

@mattytrentini 2 роки тому

@@AndreasSpiess Yes, I'm assured that the core will be available for general use - and the first can be put to sleep to run at low power.

@meinsda5983 2 роки тому

i could need your sprectrum analyzer ,)

@AndreasSpiess 2 роки тому

I can imagine ;-) It is a "biest" !

@meinsda5983 2 роки тому

@@AndreasSpiess when you stay next time in Austria/Vienna? I need this for "i don't know why not working" WLAN at a costumer

@AndreasSpiess 2 роки тому

Im Moment habe ich keine Reisepläne :-(

@jerrys2292 2 роки тому

Just a note on 5G radio waves, because of the wavelength of the wave is so much shorter the same transmit power may provide a less reliable connection. 5Ghz radio waves do not go through obstructions like 2.4Ghz radio waves. 5Ghz=6cm, 2.4Ghz =12cm. All radio waves have a hard time traveling through materials thicker than their wavelength, just something to consider as 5Ghz radio usage becomes more commonplace.

@AndreasSpiess 2 роки тому

You are right. This fact is visible with a smartphone in a house with walls.

@praveenprasannan 2 роки тому

Hope they will improve it v2. (I mean easy)

@AndreasSpiess 2 роки тому

If you know the "tricks" is is not too complicated (apart from the pins)...

@huawatuam4965 2 роки тому

Is the release date of the 5 GHz ESP32 version known?

@AndreasSpiess 2 роки тому

Not to me.

@tejonBiker 2 роки тому

Look's like a too early dev board, very promising but needs more work, thanks for the video.

@AndreasSpiess 2 роки тому

Thanks for watching!

@FVDV1 2 роки тому

Bad, too short, and non-existent documentation seems to be rampant in "maker" chips, I like to design my own boards for the ESP series chips and have banged my head so many times I lost count (luckily communities exist where a lot of extra information is available). Compare this experience to any of ST's chip documentation, it's heaven.

@AndreasSpiess 2 роки тому

I agree: Community helps a lot. This is why I still focus on the Arduino IDE and Raspbian...

@hesspet 2 роки тому

FOOW Chip? -> Fly out of window chip. My freetime for tinkering is limited. Wasting time to debug missleading or missing documentation is a nogo. This canibalizes projects due too much time is needed to bring this to live. 2,4 works here in the "outbacks" without any problems :-) So I can wait.

@AndreasSpiess 2 роки тому

After finding the "tricks" it is simple to use. This was part of the reason for that video...

@jamesmichener7526 2 роки тому

Aw... I enjoy a good adventure game. Congrats on getting out of the... "you are in a maze of twisty little passages, all alike"

@AndreasSpiess 2 роки тому

I had the choice between a rant and humor and I decided for humor...

@dreamcat4 2 роки тому

ok so i am really confused now by ESP32. because i had assumed it was ARM based MCU like all others out there. however today i look up on wikipedia it uses an 'Tensilica Xtensa LX6' ? which is it's own proprietary design? or was it actually RISC-V based to begin with? Because wikipedia also tells me that it might be the Tensilica Xtensa LX7. which is RISC-V. What i do know for sure is that the ESP32-C3 is RISC-V based, so presumably is LX7. And that the future ESP32-C6 (5ghz) will also be RISC-V based. However this does not tell me which cores has my own ESP-32 here. if it's RISC-V or not. Why i ask these stupid questions? Well because i want to know if there is any change of architectures from Tensilica (proprietary) --> to open source RISC-V. Because potentially that might lead to issues or difficulties in worse performance. Or other drawbacks IDK. The whole thing has confused the heck out of me now. Having assumed all this time it was ARM. But what I was trying to identify is how well future ESP32 (of 5ghz) will works, when compared to my current ESP32. The 2.4ghz one which we all are used to using and is $6 everywhere. And is really fast, with a low power sleep mode etc. Which is another thing. Because if the new one does not have as good a deep sleep mode. Then that would really suck :/ but maybe not so much if it kept its ram refreshed, and did not reboot itself (as you had mentioned during the last previous LoRa WAN video). Anyhow hope you are doing well. It was good effort here to try to figure this mess. For the flashing etc. BTW i think i missed the part in the video where the LED started to blink. Maybe I lost attention for all the other serial nonsense, all getting in the way. But still, i think you did an excellent work here to explain this device. Many thanks

@AndreasSpiess 2 роки тому

Espressif never used ARM cores and they started to experiment with RISC-V. The easiest way to get to the truth is always to read the datasheet. If you use C++ the architecture is probably not as important because must of the periphery anyway is not open source (see my RISC-V video).

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.

@chuxxsss 2 роки тому

The 2.4 GHz network at my place keeps dropping IOT stuff and it is not the router. I have replace the router with no difference Andreas.

@AndreasSpiess 2 роки тому

My router has problems with too many fixed IP addresses. I had to go back to automatic assignments...

@chuxxsss 2 роки тому

@@AndreasSpiess Automatic is the same, house has lots of IOT stuff.

@MatsK007 2 роки тому

Minor spelling error: RTL8720 / BW16 %GHz WiF change to: RTL8720 / BW16 5GHz WiF

@AndreasSpiess 2 роки тому

Thanks.

@HAGmbHkeG 2 роки тому

I like how it errored on the UART upload but then tells us it's "done".

@AndreasSpiess 2 роки тому

I considered that as part of the game ;-)

@varunkoganti9067 2 роки тому

Okay I'll try to create a board based on this, with having 2 USB ports one for programming and other for AT & also remove the NC pins. This should be nice project

@AndreasSpiess 2 роки тому

Good idea. And try to mark the pins correctly ;-)

@taranagnew436 2 роки тому

whould this be powerful enogh to run a 32x32 led matrix?

@AndreasSpiess 2 роки тому

I do not know :-(

@houserental5424 2 роки тому

These Realtek Amebas have been making powerful but poorly documented , hard to program WiFi chips for like 7 years now

@AndreasSpiess 2 роки тому

Good to know. I did not know them until recently because I had no need when they supported only 2.4GHz.

@Dorff_Meister 2 роки тому

At 8m 0s you are about to write some code and I've already given up on this MCU. Terrible labels, bad documentation, less flash. Needing to jumper for programming was the icing on the cake. So far the ONLY advantage I can see is Wifi6. Everything else is worse than the ESP32 chips I use now. Continuing on with the video... Conclusion, yeah, I could make it work but I'm not needing 5ghz at this time, so I'll stick with the ESP32. I'm hoping the next ESP32 has better analog inputs, too.

@AndreasSpiess 2 роки тому

Good decision!

@shrikantnikam2426 2 роки тому

Great

@AndreasSpiess 2 роки тому

Thank you!

@aleksanderhr.fredro8407 2 роки тому

probably just teething problems for a new platform, or is it not new? First time I hear of realtek small MCU modules

@AndreasSpiess 2 роки тому

The module is not new. But AFAIK the Arduino integration. At least, I never heard of it, too.

@oxenforde 2 роки тому

Years ago, I worked on a project with three sets of engineers. Everything was labeled differently. The customer was not happy. (Sound familiar?)

@AndreasSpiess 2 роки тому

Naming and labeling is very important for every project. But not all people know that…

@roperope Місяць тому

Could it be programmed using idf?

@AndreasSpiess Місяць тому

I do not think so. Itis not made by Espressif.

@fgaviator 2 роки тому

9:24 Haha, "1. Connect LOG_TX (PA7)" but "3. Disconnect LOG_TX (PA8)". Well, PA7 or PA8 - which is it??? Seems PA8 ist actually LOG_RX (well, or is it?). That thing is one hell of a mess... Clearly no one has ever reviewed any of the documentation (nor the PCB/design). Btw: Your "BW16 Getting started" link in the description doesn't work - the URL got mixed up with the description of the following link...

@AndreasSpiess 2 роки тому

Thank you. Now the link should work. And indeed there are a few things like the one you mentioned...

@IoTProgramming Місяць тому

I introduce a direct coding method using the RTL8720 Standard SDK. I use this to introduce samples and methods for developing IOT. You can get information by visiting.