Thank you very much! The ESP8266 of mine, bought new, had a baud rate of 57600, and only gave partial RESET information. I took a blind chance and follow your flash procedure, and now I can actually run all the commands... thank you!

Made my life simple. None of other videos are so good and transparent. Have finally got AT commands working on my ESP8266. Thank you very much Saravanan.....

Definitely deserve more subscriptions, great tutorial, very simple, helped to get through my esp8266 01 configuration. I would highly recommend use external power and voltage regulator(resistors, 100uF capacitor) , plus the resistors that comes with Rx, since it may damage the chip. Thank you again good sir.

Great Video! I have been 3-4 days and finding rabbit holes and garbage. BUT, you have everything (or active links) Right Here! Thank You, Mr. S! I used a programming module from Amazon, but it still needs '0' connected to GND and 'E' connected to 3V3. [I owe you a coffee, or tea, or a beer.]

FROM PAST 2 weeks i was trying to write at commands but my esp 8266 was not responding now i got the real reason behind it.. thanks for sharing this tutorial

Thank you! This was very helpful!

You are a very good learner and teacher.

I copy Cemile B, as I agree 100%. Thank you! This is the best video for firmware update. I have been struggling with this module, and I had finally made it thanks to this video!

Thanks, you earned a subscription, you pointed me into the right direction.

Thank you sir. Great explanations and very helpful.

Thank you for this very explanatory video

thanks..you just made my day..its so simple...other videos are so messy.

Thank you! This is the best video for firmware update. I have been struggling with this module, and I had finally made it thanks to this video!

thx , you are GREAT , simple for children, you can be a teacher ! best TEACHER the WORLD

Thank you! Finally it works

This video was very helpful, thank you sir.

Very very useful tutorial 👍 thanks for your detailed explanation 🙏

I am fan of your teaching

thank you sir after a full day of rabit holes it works

Thank you! Help's a lot.

Finally I Solved the problem Thank you so much!

Thank you very much. It actually works !!!

Mr. Thank you very much, from all the tutorials i've tried, yours was the only one that worked!

Thank you ♥

Thank so much sirji you are alife saver ❤️

Superb sir

Thanks a lot!

thanks you so much sir it help me a lot

Thank you.

Reis sen bu işi biliyorsun gözünün yağını yiyim. Abi çok yakışıklısın.

100% Work , No Fek

Thanks sir. It's work. :D

Can you change the baud rate through the serial monitor on Arduino?

Sir, your video is very very helpful... thank u so much.... my ESP is working now... all the AT commands are executing but AT+CIFSR IS SHOWING ERROR.. but the wifi is connected to router..... pls advice

I followed all of your steps and after firmware update the esp8266 is on continuous reset loop, am unable to enter the AT commands. Is there a solution for this?

I've made you my guru :)

I am using Arduino nano for this. Firmware update is done. But in coolterm I am trying AT but nothing is visible. But still byte getting increase when I type. Can you help me.

all set as per your instructions but after ready AT command show error when arduino reset removed AT word received continuously and also chip is getting hot

Great content. Extend your vowels, please. On 2x speed it's hard to hear.

👍

Nice video sir, I connect ESP8266 with H3LIS331DL acceleration sensor beyond 115200 upload speed sensor value repeated. No change shown. Can you help me in this

Is it the same for ESP8266Ex ?

the AT command runs with arduino correctly ,, but when i tried with usb to ttl yp-05 converter , the AT command doesn't response

PLEASE I NEED A HELP HOW CAN I SETTING AND GETTING DATA FROME FIREBASE USING ESP8266-01

I have question: After erasing flash, the error occurs: "failed to write at target flash". and I repeat over and over again still the same error appears? How can I solve this issue?

Arduino serial monitor show error message when send AT command. When Blue led flashing sometime ready message seen on monitor, What is wrong with it! please explain!

Hello sir... I was using a esp12e in one of my blynk project.... Today suddenly it stop connecting to wifi.. I tried to connect it to my Mobile hotspot bt it did not connect... Although my boards works as i tested it with simple blinking Arduino sketch... But i am unable to figure out why i doesn't connect to the wifi... I checked all my credentials they all are correct as they work with other boards... So after some digging into Internet i thought to upate the firmware and uploaded AI THINKERS bin file as you have shown in this video.... But now When i type in AT common it writes ERROR... Show can you help me

I keep getting this message connecting .... Erasing flash... Leaving... Failed to leave Flash mode but it doesn't load the bin file any clues what may be happening? thanks!

Can't keep the power on and off without resetting? Please broo help me...

Ee sadanam enthinanu upayogikkunnathu ennu adyame onnu lekhu ayittu paranjittu thodangunnathu nallatharikkum

Hi, I Am Having NodeMCU Esp8266 ch340g I Got The Error "Fatal: Timed out for waiting Packet Header" While Uploading code Please help to solve this error Thanks in advance

it worked but when i switched it back to my original connections, it says error

I accidentally set the baudrate's rts and cts bits as AT+UART_DEF=115200,8,1,0,3 now i am unable to communicate with the esp What can i do now? Any ideas?

Dear Sir, I am facing DNS Fail error, I am not able to Transmit Data From ESP8266 to my Local WAMP Server, Can you give me your valuable time in this regard? I am facing this problem very recently, but previously it was working without any issue AT+CIPSTART=4,"TCP","SERVER",80 DNS Fail here SERVE is the name of my PC, an my WAMP is running

now it sending at command on monitor continuously!

When I create your circuit diagram and push the reset button, the blue LED of ESP-01 is not flashing. I don't understand, how can I fix this problem. For all that, I tried to flash the ESP but "Failed to connect" message occurs in the screen always. Edit: LED blink fixed, but still "Failed to connect" message occurs in the screen.

hmm ,not working. I'm pressing the button (blue light flashing on esp01) but code do not want to upload :/

I request Esp8266 01 (s) to configure with arduino mega 2560

I can't download the flasher simple

The red led on esp8266 does not on !

It always shows failed to connect

Failed to connect. This is the message i am getting in the flasher..after so many tries also result is the same..

This is very complicated

DI maintindihan padi

Thanks ... this video is helpful.