Send Data on ThingSpeak cloud using Arduino and esp8266 wifi module

2 роки тому

Send data on thingSpeak using Arduino and esp8266
link-arduino.esp8266.com/stable/pac...
#Arduino#arduinoproject#adruinouno#arduinofun#arduinofun#arduinomega#esp#esp8266#wifimodule#espwifimodule#iot#arduino#Thingspeak#cloud#thingspeakcloud#lm35#esp8266andlm35#arduinoandesp8266#arduinoandesp#arduinoproject#iotproject#thingspeakproject#cratechannelonthingspeak#
arduinotutorial#arduinoprogramming#thingspeakesp8266#thingspeaktutorial#thingspeakiotproject#thingspeakarduino#thingspeakarduinoesp8266#espandarduino#esp8266andarduino#arduinoand esp8266

КОМЕНТАРІ: 55

@3dgiftz 2 роки тому

Thnaks a lot sir. very useful. Almost I have completed my project

@saitharun2588 2 роки тому

Thanks for the great video. Keep doing amazing stuff.

@TechTooB2 2 роки тому

Thank you so much it means a lot❤😘

@nagasrihith608 2 роки тому

Very informative video, thanks and keep up the good work 🙌.

@TechTooB2 2 роки тому

Thank you so much❤ it means a lot

@gihansenanayake2416 2 роки тому

Thank you very much Amith for the video, I learnt a lot from this, it's a great video!

@TechTooB2 2 роки тому

thank you so much

@abheshekmaurya7736 2 роки тому

Wowwww bhaiya kaise kiyaaa 😮🙀🙀🙀

@thecreativetechart4536 2 роки тому

have you told that how these at commands are working so perfectly.... in maximum videos i am finding that no one is telling about the firmware and factory reset of the esp8266.. after resetting it only we will get the perfect output

@ellieelenor156 2 роки тому

Hello, I really enjoyed your video! Could I please have the code to look at?

@splendor10 12 днів тому

Thanks dear friend

@jackofalltrades2673 Рік тому

hi sir next month is my project presentation. i am doing project on IOT based health monitoring. showing spo2 in thinkspeak with the help of esp8266 and max30102. please make a video on that

@baocao6049 Рік тому

Thanks for the great video. Can you share the Arduino code?

@jamessalvador8075 3 місяці тому

Awesome tutorial, is there a way to send the data to google sheets instead of thingspeak?

@nihalsabri3071 2 роки тому

Thank You

@ritusingh2182 2 роки тому

Can you make a video to explain more about things speak cloud interface and how to use it from basic

@TechTooB2 2 роки тому

Well sure

@josephdaquila2479 Місяць тому

If I don't want to use ThingsSpeak can I just write get and post commands?

@luistimana2393 Рік тому

Thanks. Can you share the Arduino code?

@nurashikinahmad4933 2 роки тому

Can i use arduino Mega using this step ?

@viktor7425 Рік тому

Hello, I did exactly the same as you only on the mega board, but when I type the AT command on the serial monitor nothing happens, I get no response. I can use your help or just an opinion on why it wont work, thanks.

@blackglove9779 Рік тому

SAME THING I FACED WITH ARDUINO UNO

@nandhinijagadeesan3835 Рік тому

Can i connect Arduino mega with NodeMCU esp8266 and then connect to thingspeak to visualize sensor data?

@surya2557 Рік тому

U did?

@khyimful 2 роки тому

Can u show the wire connections in the wifi module?

@SaurabhYadav-yb6mz 2 роки тому

Sir ....on going to new and then uploading the code on arduino uno ....there is showing an error

@TechTooB2 2 роки тому

You can mail us on techtoob2@gmail.com for any query

@user-qw8zw1hc6h 6 місяців тому

hello,which software did you use to design your circuit?

@laus-thecurious4120 4 місяці тому

tinkercad most probably , ss is there and now tinkercad does not support esp8266

@user-np2zd8gc3h 5 місяців тому

halo, can i get this code program?

@edzellegaspi6117 2 роки тому

Hi! Can I have the code for this?

@abhikchanda6222 Рік тому

You must disconnect the tx and rx pin and upload the code after uploading the code to Uno connect rst of Uno to gnd and reconnect the tx and rx pin then only you can use AT command

@PradeepSingh-pp1nj 11 місяців тому

brother m done with uploading but cannot use AT commands can u help m using blynk tomorrow is my final capstone viva plz

@SKMINSARR 11 місяців тому

this comment save my semester

@suryatilak7741 Рік тому

Create A Circuit To Display A Message Internet Is Connected And Then When The Device Is Connected To Thingspeak And Sending Data Successfully To It, Display All This In LCD Display!!!plzz do this

@TechTooB2 Рік тому

If you want a make a project you can send the details on techtoob2@gmail.com

@chatgpt-learneverything Рік тому

Can you share the code???

@mrpankhan7171 Рік тому

Can i get code?

@santhoskumar2592 2 роки тому

Sir i am using arduino nano but the light is not blinking what to do

@TechTooB2 2 роки тому

Nano 3.3v output is not enough for esp8266 use a voltage regulator go give power to esp8266 or try with 5v but make sure that you don't keep ESP ON for long time.

@santhoskumar2592 2 роки тому

@@TechTooB2 thank you sir

@santhoskumar2592 2 роки тому

@@TechTooB2 sir it is not working for me kindly help me sir i am working on my mini project, how can i contact you

@TechTooB2 2 роки тому

@@santhoskumar2592 mail me on techtoob2@gmail.com