Speed Up Your Acer Nitro 5 AN515-57 - Prevent Overheating With Dust Cleaning & New Thermal Paste
Переглядів 83,777
11 місяців томуGet ready to revitalize your laptop by reducing your CPU’s temperature by 43 degrees Celsius in just six easy steps. Follow and subscribe to Kooling Monster and let us know which laptops to demo this process with next.
【PERFORMANCE/OVERHEATING SOLUTIONS】- available across the globe!
KOLD-01 Thermal Paste: bit.ly/kold-01-yt
KLEAN-01 Thermal Paste Cleaning Wipe: bit.ly/klean-01-yt
KOMBO-01 Screwdriver Set: bit.ly/kombo-01-yt
Air Duster: amzn.to/3YTclrP
【THERMAL PASTE KNOWLEDGE】
Thermal Paste Performance Comparison Test: bit.ly/bestthermal
How Much Thermal Paste Do I Need: bit.ly/thermalcal
How Often Should I Replace Thermal Paste: bit.ly/thermaltime
What Is the Best Thermal Paste Pattern: bit.ly/thermalpattern
More Thermal Paste Knowledge: koolingmonster.com/insights
【ABOUT Kooling Monster】
Our vision is to make PC performance upgrades simple and low-cost for all. We hope to popularize DIY computer repair skills, enabling everyone to achieve significant performance improvements at an extremely low cost, while also reducing the negative impact on the environment.
【DISCLAIMER】
This video is for general information. We will not accept any liability for damage caused while following this guide.
@takasytuacja5133 8 місяців тому
Thermal pads should be replaced with thermal pads not thermal paste. Also removing motherboard small battery is recommended before You start disassembly.
@koolingmonster 8 місяців тому
Hi! There will be no negative effect if replacing thermal pads with thermal paste. Especially with our KOLD-01 thermal paste, our special design enables it to have enough viscosity to replace the thermal pads.
@Brightshadow686 10 місяців тому
Watching you put on the termal paste was a bit brutal, but for the rest of the video, i want to say thanks. I have around 50° on idle, and when cpu is on 13% my temperature is on 91° so i wanted to change my thermal paste. Even when the laptop is just 2 years old.. i will never buy an acer again..
@koolingmonster 9 місяців тому
Thank you for your reply! We are very happy to know that our tutorials and videos might be of help. Here is the link to our KOLD-01 Thermal Paste product page if this helps! koolingmonster.com/thermalpastekold-01
@christianjayhizon4825 9 місяців тому
never use your laptop unplug because it can cause more heat due to power consumption from the battery. Never let your battery go below 20% it degrades your battery life.
@lawson1989 9 місяців тому
You have to use throttle stop and uncheck use turbo for Acer
@syrakx 8 місяців тому
bruh you expect your laptop to clean on your own?😂 you need to apply thermal paste after year of using it
@phyxiox 8 місяців тому
bro my Nitro 5 is less than a year old and it's cpu is at 92° at 10% usage and my gpu is at 86° at ~98% usage, you're good lol
@ParadoXGaminGMijat 7 місяців тому
Well,thanks for tutorial.Cleaned from dust,and some weird stuff,replaced only thermal paste with MX4,i had that one near me,from 92c in games to 71c,thats alot. 👍👍👍
@koolingmonster 7 місяців тому
You are very welcome. We are glad that our tutorial has helped you. We hope that our products might be of help as well in the futrue! Our KOLD-01 Thermal Paste uses a special non-solvant formulation design that can prevent paste drying up and losing thermal conductivity, resulting in longer lifespan.
@itsmevario420 4 місяці тому
Can you help me to decide between this ACER Nitro 5 and *Asus Tuf / 11400H / 3050 / 16GB / 512GB M.2* Please help :))) Cheers!!@@koolingmonster
@slupot 4 місяці тому
@@koolingmonsterI picked up a tube of your product and about to replace my paste with it, on same model of laptop.
@koolingmonster 4 місяці тому
@slupot Thank you for trying out our products! We hope the thermal paste will help you with your laptop!
@mitolhack4233 9 місяців тому
Thank you, my laptop now is going at lower temperatures :D
@koolingmonster 8 місяців тому
You are very welcome! We are glad that our tutorial and products might be of help!
@nonotatallnothanks 4 місяці тому
this is a great video for anyone using this recently my tip is to make sure that you are gentle with the atennae for the wifi chip at 5:55 bc I have such big hands it came off easily but never went back on, unfortunately replacing the ends of these white and black cables isnt possible so make sure to be gentle when putting them back on!! (luckily i use ethernet anyway but beware if u use wifi)
@nonotatallnothanks 4 місяці тому
if you did the same as me don't be too concerned you can either a. soder it back on or b. replace the cables entirely ( but this process is lengthy and hard bc u remove the mobo)
@nonotatallnothanks 4 місяці тому
or leave it alone if u dont care lol
@koolingmonster 4 місяці тому
Thank you for the great advice for everyone!
@nonotatallnothanks 4 місяці тому
@@koolingmonster thank you! your name fits perfect my computer is now also a kooler monster
@koolingmonster 4 місяці тому
Thank you for the nice words! We are glad that our products might be of help!
@arvinyao7350 9 місяців тому
Thank you! Just follow the video and you won’t have any problem.
@koolingmonster 8 місяців тому
You are very welcome. We are very glad to know that our tutorials and products might be of help.
@sense5151 10 місяців тому
Im going to try this, thank you
@sense5151 10 місяців тому
It worked, from 60c idle to 40c thank you sooo much
@koolingmonster 9 місяців тому
WOW! That is some amazing improvements! We are so glad to know that our products have helped you.
@johnjoson5908 8 місяців тому
@@sense5151hi this is a question about the thermal paste is your computer still good and was it this the thermal paste you used?
@carlosr6547 10 місяців тому
Excelent video!! More videos like this!
@koolingmonster 9 місяців тому
We are so happy to know that our videos and products might assist you! We will keep on making more videos!
@TV-ti3pj 5 місяців тому
Thank you very much. The video helped a lot
@koolingmonster 5 місяців тому
You are very welcome! We will continue to make videos like this!
@serahex 5 місяців тому
Great video, thank you!
@koolingmonster 5 місяців тому
You are very welcome! We will continue to make these videos!
@o_o6133 8 місяців тому
Good tutorial, however i wouldnt reccomend using thermal paste instead of thermal pads on the video memory chips
@koolingmonster 8 місяців тому
Thank you for liking our video! We understand your concern, however our KOLD-01 thermal paste has special rheology design that allows it to have high viscosity and can do the job of thermal pads. There will be no negative effect replacing those with thermal paste.
@rafiffz 7 місяців тому
Thanks 👍👍👍
@koolingmonster 7 місяців тому
You are very welcome. We're very glad to know that our tutorials or products might have be of help!
@alonsocruz8720 8 місяців тому
Hola, cuáles son las medidas de los tornillos del disipador? muchas gracias 🫂
@koolingmonster 8 місяців тому
Hola, lo mejor es preguntar al fabricante.
@dezessete1782 9 місяців тому
Friend, only with phO can I disassemble? or does it need to be a pho bit? I'm having trouble with 3 screws that won't come out at all lol. Nice movie
@koolingmonster 7 місяців тому
Hi friend! We are glad that you liked our tutorial. We recommend always using the correct screwdriver bit when removing screws. Sometimes the wrong head can also remove screws, but you are in danger of stripping the screws and having them stuck in the laptop. You could give our KOMBO-01 screwdriver a try. It has differennt replacement bits specifically designed for computer disassembly.
@izedawidka 9 місяців тому
Im not sure that ripping off the pads and just drowning the area in thermal paste was a very good call
@koolingmonster 8 місяців тому
We understand your concern, however our KOLD-01 thermal paste has special rheology design that allows it to have high viscosity and can do the job of thermal pads. There will be no negative effect replacing those with thermal paste.
@jitadityakahayap5581 9 місяців тому
I also cleaned the pink thermal paste around the chipset if we put normal thermal paste will this would be safe ? Or either it can effect the motherboard in future can you plzz explain?
@koolingmonster 8 місяців тому
We understand your concern, however our KOLD-01 thermal paste has special rheology design that allows it to have high viscosity and can do the job of thermal pads. There will be no negative effect replacing those with thermal paste.
@michaelpoh4837 8 місяців тому
Hello 👋 Both slot Pcie nvme M.2 able support 2 x 2 TB ? Then can put in each Single slot 1 and slot 2 With 2 TB and total 4TB ? For this model (2023) Acer nitro 5 AN515-47-R3JC
@koolingmonster 8 місяців тому
Hi. There are no limitations on the drive capacity. As long as it is a nvme M.2 SSD, you can install whatever capacity drives you want.
@slupot 4 місяці тому
I personally did exactly what you are asking. On the same exact ACER nitro. 2tb x 2 m2ssd drives. Samsung Evo 970. Also upgraded to 16x2 ram for 32gb total. Works great.
@nikohaavisto3161 4 місяці тому
thanks :)
@koolingmonster 4 місяці тому
You are very welcome! We are very glad that our tutorial or products might be of help!
@Circuit_Savvy 10 місяців тому
Should I paste my laptop? Its the same As yours in the video. Its 1* year old and I also want to clear debris from the exhausts.
@koolingmonster 9 місяців тому
Thank you for your reply! We are glad that our video and products may be of help. We recommend changing thermal paste on a laptop after six months to one year. However, other aspects such as your use case should also be considered. We suggest measuring the CPU and GPU temperature as well. Here’s a link to one of our articles that might help: koolingmonster.com/insights/how-to-know-if-your-thermal-paste-needs-replacing-step-by-step-tutorial
@kasiitaali 7 місяців тому
Do you have the kit available in the uae
@koolingmonster 6 місяців тому
We will be able to sell our products to the UAE very soon! For now, available countries can be found in the links in the description.
@codeon3406 9 місяців тому
The pink paste in mine is completely dry and i can break it off by lightly touching it 😂 had my laptop for 4 years
@koolingmonster 8 місяців тому
We are glad to know that you decided to open up your laptop and change the thermal paste! Sounds like your laptop really needed some new paste! We hope that our tutorial and products have helped you!
@migren99 10 місяців тому
i am using the same computer i accidentally removed the thermal pads. Now the heatsink is not touching the gpu and the temperatures have increased excessively. I couldn't find out how many millimeters the thermal pads are. If you have any information, I would be glad if you could help
@koolingmonster 9 місяців тому
You can just apply thermal paste whatever components the thermal pads was on. Thermal paste have better heat conduction than thermal pads, and are also better at filling in smaller gaps that the solid thermal pads cannot. Here's a link to our article on thermal paste vs. thermal pads. Hope this can help! koolingmonster.com/insights/cpu-thermal-paste-vs-thermal-pad-which-is-the-best
@goorthiss 9 місяців тому
If you do not want to burn the vrams and power section, then I recommend applying thermal putty such as Upsiren UX Pro, which was created for this purpose. Has anyone encountered a case where a laptop manufacturer applied paste instead of thermal pads or thermal putty on the vrams?
@ggoddkkiller1342 9 місяців тому
@@koolingmonster That's just a bad advice, VRAM can work until 120 degree which is way too much for most thermal paste in the market and they would dry out in no time..
@mitolhack4233 9 місяців тому
It is 1 mm thickness
@benedictxavier8809 9 місяців тому
@@koolingmonster how about liquid metal on all of it
@batokelapa9777 10 місяців тому
U change thermal pad with paste ? isn't there a gap?
@koolingmonster 9 місяців тому
Thermal paste is has better heat conduction than thermal pads. Also, thermal pads are solid materials, whereas thermal paste is grease, therefore thermal paste can fill smaller gaps that thermal pads simply can't. Here's a link to our article on thermal paste vs. thermal pads. Hope this can help! koolingmonster.com/insights/cpu-thermal-paste-vs-thermal-pad-which-is-the-best
@goorthiss 9 місяців тому
@@koolingmonster Instead of thermal pads, for example, on the vrams and power section, it is used thermal putty such as Upsiren UX Pro. In most cases, thermal paste will not adequately efficiently transfer heat because the heatsink will not adhere or the paste layer will be too thick, above a thickness of ~0.5mm also paste transfers heat poorly. For the CPU/GPU cores, I recommend applying PTM7950.
@hogsa7287 9 місяців тому
Please a video for the Gigabyte Aero 15.
@koolingmonster 8 місяців тому
We have added Gigabyte Aero 15 to our production list. We will mention you when the video comes out. Stay subscribed!
@albergr98 10 місяців тому
I need that spatula to extend my thermal paste, any links to it?
@koolingmonster 10 місяців тому
Our KLEAN-01 Thermal Paste Cleaner kit as well as KOLD-01 Thermal Paste kit both have spatula included. We also include other tools such as spreaders to help with the cleaning and thermal paste changing process.
@headshotchannel2993 9 місяців тому
you don't have to extend the thermal paste, just apply it and put your cooler back on
@koolingmonster 7 місяців тому
You are correct. Spreading thermal paste is not required but is a easy way to check if you applied too much thermal paste. Accoring to our study, as long as the amount of thermal paste used is correct, the application method and whether you spread thermal paste or not does not matter. You can view our detailed experiment here: koolingmonster.com/insights/is-the-buttered-toast-method-a-good-thermal-paste-pattern-vs-the-pea-size-method@@headshotchannel2993
@9669ghost 10 місяців тому
Is it okay to use regular grey paste on vrams ?
@koolingmonster 9 місяців тому
It is totally OK to use thermal paste on vrams. Thermal paste has better heat conductivity and is better at filling in small gaps as well. There's no need to worry, switching to thermal paste can also help the laptop perform better. However, we do recommend using higher quality thermal paste for this. You can learn more about our KOLD-01 Thermal Paste here: koolingmonster.com/thermalpastekold-01
@takasytuacja5133 8 місяців тому
No. Use thermal pads instead.
@_harsh.04 4 місяці тому
hye? can i know the thermal pad thickness for the laptop?
@koolingmonster 4 місяці тому
The thickness is different for every laptops, you might need to measure yourself.
@vortexyt78 9 місяців тому
Can u suggest me Ram for Acer Nitro 5 AN515-57 which currently has a Kingston 8gb ddr4 3200mhz 1Rx16.Will 1Rx8 run with 1Rx16 which are manufactured by different companies.
@koolingmonster 8 місяців тому
Yes, however it is best to use the same ram sticks in one machine.
@manasMahendra 4 місяці тому
Hey does anyone know where to get these adhesive tape please help
@koolingmonster 3 місяці тому
Hello, you may go to a computer material store to get these adhesive tape.
@evestik 4 місяці тому
Question, I use a acer nitro 5 rtx 3050 and everytime I play heavy games like cyberpunk it cuts my battery from charging and reduces my the laptops performance, even after setting the game to high performance it still cuts my laptop battery power and reduces quality and start lagging please help 😢
@koolingmonster 4 місяці тому
It is hard for us to diagnose the exact problem just through these information, but thermal issues can cause laptops to cut power and slow down.
@perbyvalencerina5579 5 місяців тому
Help. I followed the steps. But the screen now wont turn on. It seems to be getting power but not display. Ive re checked the screen wire
@koolingmonster 5 місяців тому
We are very sorry to hear that. Try double checking the display connector cable, as well as the power cable. We hope your issue can be resolved soon!
@howl_of_the_south 7 місяців тому
Im having a lot of issues on screw 3, anyone else? 2:15
@koolingmonster 6 місяців тому
Is ths screw stripped? First make sure that you using the correct screwdriver bit? You can try to remove the stripped screw with rubberband or gaff tape on the screwdriver bit. We have a tutorial specifically on this matter on our website. koolingmonster.com/insights/how-to-remove-a-stripped-screw-from-laptop-and-pc-using-only-household-tools
@howl_of_the_south 6 місяців тому
@@koolingmonster Looks like The screw was molten in place, I took it to someone with more experience and everything came out right
@staveplayz4797 10 місяців тому
My laptop ain’t turning back on even though I followed the steps thoroughly
@koolingmonster 10 місяців тому
There are many reasons that can lead to a laptop not turning back on. Try first charging the laptop incase the battery died. Then try if the power cable is fully inserted on the motherboard. If the problem isn't solved or you need additional help, please feel free to leave more comments and we are happy to help.
@johnjoson5908 8 місяців тому
Did you put your battery plug back in and what happened?
@tjlaser99 8 місяців тому
Hi, I need help, the laptop doesn't want to turn back on.
@koolingmonster 7 місяців тому
"There are many reasons that can lead to a laptop not turning back on. Try first charging the laptop incase the battery died. Then try if the power cable is fully inserted on the motherboard. If the problem isn't solved or you need additional help, please feel free to leave more comments or contact us and we are happy to help."@@tjlaser99
@xiaodhruv7693 5 місяців тому
Hey, I don't want to change thermal paste, but i want to clean fans, is changing paste necessary?
@AmieWea 5 місяців тому
No it does not necessary. I just cleaned mine and the temp drop to some degree.
@osiris8940 5 місяців тому
No
@koolingmonster 5 місяців тому
To get most result out of the cleaning, it is very necessary to change the thermal paste. Cleaning the fans improves heat transfer from heatsink to outside the laptop. Changing the thermal paste improves heat transfer from CPU to heatsink.
@xiaodhruv7693 5 місяців тому
@@koolingmonster thanks for this, actually i bought my laptop 7-8 months ago, And i didn't knew that laptop shouldn't be used on bed 💀, it started collecting dust from my bed, I belive my thermal paste are fine completely, it's just my fans are so dusty, Thank you so much 🫂, if my thermal paste looks bad i will change it ☺️
@koolingmonster 5 місяців тому
You are welcome! Yes laptops collect dust more if they are often used on the bed. But dust cleaning will solve the problem!
@casualridingtv9461 4 місяці тому
How much thermal paste do I need to buy? Is 5.4g enough?
@koolingmonster 4 місяці тому
The 5.4g option is definitely enough for a one-time use. If you are planning to change your thermal paste regularly in the future, we suggest choosing a larger option.
@quincyhampton3243 6 місяців тому
Instead of a air duster can i use a electric one😊
@koolingmonster 5 місяців тому
Of course, just make sure not to damage the components.
@DaCouchWarrior 6 місяців тому
For gods sake is it possible to clean those without compressed air?
@koolingmonster 5 місяців тому
Yes! Just make sure to clean the dust out as much as possible and you will see some improvements!
@abyssuschl 8 місяців тому
The fans are supose to throw air or suck it?
@koolingmonster 8 місяців тому
Hi. The fans in a computer suck in cool air from outside and throw out the hot air from inside.
@lovishverma6729 10 місяців тому
I forgot to disconnect my laptop battery while cleaning and changing thermal paste What should I do!!??
@koolingmonster 9 місяців тому
We suggest always disconnecting the laptop battery when accessing the internals. It is also important to wash hands to prevent static electricity from damaging the motherboard. If your laptop turns back on and does not malfunction, you should not worry too much.
@Chris-pl9ru 9 місяців тому
@@koolingmonsterI did the same thing he did but only with the long black wire and the fan wire after I noticed what I did I plugged them back in and did everything else after I was done I plugged my computer in and the charging light turned on for a second and turned off and ever since then nothing’s been responding won’t show it’s charging or turn on
@koolingmonster 7 місяців тому
Sorry to hear about the issue. It sounds like there may have been a short circuit when the wires were unplugged. Try these steps: 1. Double-check if all connectors are secure. 2. Reset the battery or disconnect it for a few minutes, then reconnect. 3. Try powering the laptop with only the charger, without the battery. If it still doesn't work, I'd recommend seeing a professional technician. Always disconnect the battery before working internally to prevent issues.@@Chris-pl9ru
@TheCoopChannel 8 місяців тому
My man is putting 2kg of thermal paste loll
@koolingmonster 8 місяців тому
We use our thermal paste calculator to determine the best amount of thermal paste to use. koolingmonster.com/insights/estimate-how-much-thermal-paste-you-need-on-cpugpu-with-a-calculator . Also we spread out the thermal paste before putting back the heatsink to check of we put on too much or too little of paste.
@sendrih9882 9 місяців тому
Thermal paste is needed on gpu and cpu, but thermal pads are better on chips
@koolingmonster 8 місяців тому
Thank you for your reply! There will be no negative effect if you replace the thermal pads with KOLD-01 thermal paste because of its high viscosity design.
@okay2427 10 місяців тому
"thermal paste has dried up after several years of use" the laptop was launched only 1 year before
@koolingmonster 10 місяців тому
Thank you for your reply! We will improve our script in the future.
@peepeepoopooeater 9 місяців тому
I cant remove the screws its all stuck am i fucked
@koolingmonster 7 місяців тому
We are sorry to hear that. Are you using the correct screwdriver bit? Is there a chance that you tried to remove the screws with a wrong bit and the screws are stripped? You can try to remove the screw with rubberband or gaff tape on the screwdriver bit. We have a tutorial specifically on this matter on our website. koolingmonster.com/insights/how-to-remove-a-stripped-screw-from-laptop-and-pc-using-only-household-tools
@Kerem-qh1jm 6 місяців тому
fans still dirty.
@koolingmonster 5 місяців тому
Thank you for the comment, we will improve our content in the future!
Настоящее Время. Док
Переглядів 11 млн
northwestrepair
Переглядів 1,7 млн
Kooling Monster
Переглядів 2,7 тис.
DandyWorks
Переглядів 680 тис.