Swapping FZ1 Rotor, Before it EXPLODES!

  Переглядів 116,294

AndyManCam

AndyManCam

4 роки тому

AMC T-Shirts, Hoodies, Caps and MORE available now!
Get yours at: shop.spreadshirt.co.uk/andyma...
---------------------------
The Yamaha FZ1 is a fantastic bike, with a few potentially disastrous shortfalls. One of those is the Rotor unit that was built into the earlier models. This early rotor design has adhesive bonded magnets which through vibration, heat or plain bad luck, have the potential to come loose and cause a hand grenade like effect on the innards of the engine. 'Thankfully', Yamaha realised this error (though they never admitted that it was an error) and created an improved design in which the magnets were sheathed behind a metal wall, thus rendering them forever imprisoned and unable to destroy any more poor innocent engines!
In this video I will be preemptively swapping out my old rotor for the newer design so that I can stop having nightmares about my bike committing Harikari while I'm 6000ft up on a mountain pass!
AFAIK This fix is relevant for the FZ1 all years up to and including 2014, but there’s probably some overlap so the only way to be sure is to check!
It's also exactly the same rotor (and I assume same problem) with the FZ8 from 2010 onwards and the YZF-R1 from 2004 - 2008.
The old part number is: 5VY814500000
The NEW part number is: 2SH-81450-00-00
I have seen a few people advertising Rotors under the new part number, but actually selling the design with the exposed magnets. So watch out! If you can SEE the magnets, leave it WELL alone!!
That being said, apparently there is still a market for your old Rotor once you've completed the swap. But that's a moral dilemma for you to work out with your own conscience as to whether or not you feel happy selling a part that could very well destroy somebody else's bike!!
[[------ NEW AMC STICKERS! -----]]
Black Camera: bit.ly/AMCamblk
White Camera: bit.ly/AMCamwte
Black Mount Yin: bit.ly/AMCmntyinblk
Black Mount Yang: bit.ly/AMCmntyangblk
White Mount Yin: bit.ly/AMCmntyinwte
White Mount Yang: bit.ly/AMCmntyangwte
Black Set: bit.ly/AMCsetblk
White Set: bit.ly/AMCsetwte
FULL SET: bit.ly/AMCfullset -----------------------------------------------
MUSIC from this video is from Soundstripe: soundstripe.com?fpr=amc20
Get AMC's ALBUM here: bit.ly/AMCcd
(includes channel theme tune: 'Happiness')
-----------------------------------------------
Help me make better videos by supporting the channel through Patreon: www.patreon.com/andymancam
-----------------------------------------------
My Gear:
Clothing: goo.gl/hNbkCr
Tyres: moto.michelin.com/DC/en/tyres...
Audio Recorder: amzn.to/2QYrVnv
Intercom: amzn.to/2CY9KpJ
Sony X3000 Action Camera: amzn.to/2GtfwyT
Sony AS200vr Action camera: amzn.to/2mvfYX9
RAM Mount: amzn.to/2PyRJSw
RAM Clamp: amzn.to/2M2S9Ok
SW-Motech 'City' Tank Bag: amzn.to/2MpQwwE
SW-Motech 'Blaze' Panniers: amzn.to/2Mrx8PT
3M Dual Lock: amzn.to/2MuNN5g
Wera Tool-Check Plus ratchet set: amzn.to/2nqq6OB
Leatherman: amzn.to/2nfNMrx
Gear Gremlin Cable repair Kit: amzn.to/2nfI2ya
--------------------------------
FOLLOW me on
Twitter: / andymancam
Instagram: / andymancam
Facebook: www. andymancam
--------------------------------
I am a participant in the in the Amazon EU Associates Programme & Amazon Services LLC Associates, an affiliate advertising programme designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.co.uk & Amazon.com

КОМЕНТАРІ: 766
@NETRAracer4636
@NETRAracer4636 Рік тому
You, my friend, are a life saver. I may not have had the confidence to tear this apart without this very descriptive and well made video. Thank you!
@AndyManCam
@AndyManCam Рік тому
Thank you kindly Matt. It was a little adventurous for me too, just to delve in! Alls well that ends well eh?! 😉
@ludvigknoosfranzen2906
@ludvigknoosfranzen2906 Рік тому
Just did the swap with your video in the background! Worked perfectly and took less time than I expected! Ordered the rotor from EFS RMSTATOR Europe, in case anyone is looking for one 🙂
@bigduphusaj162
@bigduphusaj162 4 місяці тому
The RM part is worse than stock it lasts 2yr. You should have checked the reviews mate as its been known for a while the RM part is a disaster.
@n.m.mn.m.m2078
@n.m.mn.m.m2078 Місяць тому
@@bigduphusaj162where do u find this info?
@tiger98011
@tiger98011 2 роки тому
Finally installed mine yesterday on my 2011. Was a bit snug coming out, but I really appreciated you pay on putting it back in! My assembly came apart between our of the old and onto the new, so had to check the ship manual for the order of parts, but you video held me snap it back into the beating in about 1 minute by reaching my fingers to the back and turning one of the rotors to line them up. Thank you.
@AndyManCam
@AndyManCam 2 роки тому
Very happy to help and glad you got it all back together Greg!
@wilcovandenboom6797
@wilcovandenboom6797 3 роки тому
I wish i once had teachers/tutors like this hero...bloody norah. A real treat to see and hear! Thanks a lot!
@AndyManCam
@AndyManCam 3 роки тому
Kind words! Thanks Wilco! I’m very happy to have helped!
@totolorenzana
@totolorenzana 4 роки тому
I just changed it today, it gives me peace of mind knowing it has the updated part. THANK YOU FOR YOUR VIDEOS, THE INFORMATION AND THIS TUTORIAL!
@AndyManCam
@AndyManCam 4 роки тому
My pleasure Roberto! I hope you have many long and happy miles now!
@1oldman668
@1oldman668 2 роки тому
Thanks Andy for the video. I know you’ve moved on but I just love my 2012 FZ1. Changed handlebar position, Yoshi exhaust Woolich tuned, it is so much better than stock - so smooth. At approx 37000 km, I decided to replace the Rotor. Followed your video, it was the best out there and so accurate 😎. When I pulled the rotor out, the gears, washer and spacer all came out with it so my biggest fear vanished. The old rotor was in perfect condition 🤔 - and I paid $$ for an OEM replacement 😳. Thanks for your help. Love the riding videos but also the garage ones. Keep it safe and thanks for your positive inspiration. If you ever come to Australia, I’d love to shout you a beer and take you for a ride.
@AndyManCam
@AndyManCam 2 роки тому
No surprise mate, it’s an awesome bike! That’s the real kicker with that rotor. It looks totally fine, until it’s not! Might never go, could explode tomorrow. At least you know that you’re 100% safe now!!
@ArielSaez
@ArielSaez 4 роки тому
Having seen your video, now I encourage myself to do it when my new rotor arrives. Thank you very much for sharing! Greetings from Argentina!
@AndyManCam
@AndyManCam 4 роки тому
I can only recommend it! I sleep better now, knowing that I should be good for a while now!
@docsamson2299
@docsamson2299 Рік тому
Found your channel and decided to go with a good deal on an 07 FZ1. Appreciate you taking the time to make these vids and took care of this particular issue this past weekend! Was not prepared for just how much pressure was needed to keep the rotor in place whilst pulling the stator and cover apart! Got lucky as my whole assembly (rotor, gears, spacers, and washer) all pulled out as a piece. Thanks for the e-help! 👍
@AndyManCam
@AndyManCam Рік тому
That’s good news. Both the job being done and nothing going into the block! Happy riding now Doc!
@codyalcorn8891
@codyalcorn8891 8 місяців тому
I just bought an 07 FZ1 as well... Needs a little TLC but couldn't pass up on the deal lol and plus parts are really cheap to make it look like a brand new bike. But it has 24k on it and watching this I almost want to change this part out as well lol.... I'm sure mine has the OEM. But I don't want anything to happen to the engine if I'm dumping 1500$ into it on parts and aftermarket stuff, etc.
@AndyManCam
@AndyManCam 8 місяців тому
It’s definitely worth it for peace of mind.
@bigduphusaj162
@bigduphusaj162 4 місяці тому
​@@codyalcorn8891its over hyped and not that common. Only a couple of hundred bikes between 2004 and 2005 (if its the a 5VY R1) and 2008 models had the same issue again breifly with the non O-ring part. Ive heard people say it grenades the engine yet still to find a 5VY R1 wrecked because of it. It a bike mechanic of 4 decades BTW and kept all the replacement ones which ive just had a look at them all again yesterday. Most are fine and the better epoxy with the slightly differnent shaped magnets. Ohh and stay away from the RM part its worse than the original part, its not even machined correctly and the sheath has been known to touch the staitor magnets the lot. The wiring on it is abysmal too so avoid that junk at all costs. Again, the 5VY R1 is regarded as one of the most reliable bikes ever made so thats how bad this issue really is. Ive only witnessed one failure of it on a 2008 R1 when they did the same mistake again. Its the oil eats the 3M epoxy they use West Systems 105 now on the upgraded part
@durandhemminger7373
@durandhemminger7373 Місяць тому
My fz1 has 59k miles. I never changed this. Want to now
@cklamNL
@cklamNL Рік тому
Extraordinary explanation, all do's and don'ts. When I was removing the rotor I was really terrified that parts would fall into the engine case but guess I was lucky. Thanks for the video!
@AndyManCam
@AndyManCam Рік тому
Thanks CK, cheers for watching and glad yours went smoothly!
@seeul8rwaynekerr
@seeul8rwaynekerr Рік тому
Thankyou for this lovely guide AMC. I've just gone and done the change from the grenade rotor to the newer captive magnet variety. I've used the cereal box cardboard technique to avoid it eating the washer or bearing spacer. Putting the bike in 6th gear allows you to force the engine round by the back wheel and then get the flywheel jug properly meshing. Anyway thankyou for your lovely video and keep up the good work I still think the fz1 once this is done is better than the current honda machine you're rocking.
@richardbanks725
@richardbanks725 Рік тому
What a brilliant video!! Gave me the confidence to do mine before it went bad and was really easy with your instructions, so massive thanks!!
@phillipangell5131
@phillipangell5131 4 роки тому
AMC. I have been without internet access for 6 whole weeks, yours was the first video I watched upon my return, how I missed you you'll never know!
@AndyManCam
@AndyManCam 4 роки тому
What absolute HELL that must have been for you! :O At least you're finally back and getting your fix! ;D
@russelllocke7180
@russelllocke7180 4 роки тому
I’ve never seen that job done before Andy. The little tips you provide in making the task easier are helping my less than average, but improving, home servicing skills. Cheers. 👍🏍🇦🇺
@AndyManCam
@AndyManCam 4 роки тому
Thanks Russell. Happy to be even vaguely helpful!!
@Cyverion
@Cyverion 3 роки тому
Many thanks for the helpful video. I'll be tackling this myself during the coming winter months.
@AndyManCam
@AndyManCam 3 роки тому
My pleasure! Hope your fix goes well.
@ttsupra87
@ttsupra87 3 роки тому
Nice! Just found out about this issue and thinking of doing the swap you made it look super easy
@AndyManCam
@AndyManCam 3 роки тому
It is easy, until everything falls into the bike! I'd say put the bike on the side stand, just to give you an advantage for when you'Re pulling it out.
@cannedSardina
@cannedSardina 2 роки тому
Good vid dude. I’ll be watching this while performing this rotor swap this weekend.
@RoadDogSteve
@RoadDogSteve 4 роки тому
Well done... Researching procedures is so easy... I always enjoy the knowledge and humor.... Torqueing fasteners is so critical... Especially if a sequence is called for... Hope your pinched finger episode didn't demonetize vid.... Thanks again...
@AndyManCam
@AndyManCam 4 роки тому
Cheers Stephen. My pleasure. I'd take the demonetization in return for still having a finger and not worrying about the bike exploding!
@johnkelly5816
@johnkelly5816 2 роки тому
Thank you AndyManCam, useful guidance indeed, love the touring vids also, I have an FZ1 S 2010, same genealogy for sure. Great motor. Now swapped out the rotor and could not have done it without watching this vid for tips. If you ever make it over for the IOM TT I’ll stand you a burgher and a pint at the Grandstand beer tent.
@johnsharpe4131
@johnsharpe4131 4 роки тому
You deserve a thumbs up for not swearing more when the magnets grabbed the cover back on. made me flinch just watching.
@AndyManCam
@AndyManCam 4 роки тому
The self control of a tibetan monk. (Mum watches the videos and doesn't like the bad words!!)
@JetMech100
@JetMech100 4 роки тому
Just found your channel. Instantly subscribed. Great content. And thanks for the info. I have a 2007 FZ1 so I might have to look into this.
@AndyManCam
@AndyManCam 4 роки тому
Thanks very much mate and welcome to the channel! I was losing sleep thinking about this bloody rotor nonsense. Especially as I have a trip coming up soon! SO glad I got it out of the way!!
@scottc3
@scottc3 4 роки тому
Good work. Preventative maintenance is always worth it! Particularly with engine components. 👍
@AndyManCam
@AndyManCam 4 роки тому
I totally agree. Though that shows that we are all finally adults! At 20 yrs old, I would have waited until the bike was in flames at the side of the road before spending money on parts!!
@falseneutral7890
@falseneutral7890 4 роки тому
Respect for staying calm after being "bitten" by the bike, I know I wouldn't have 🤣 Nice tutorial 👍
@AndyManCam
@AndyManCam 4 роки тому
Cheers! I had to remember several things. Firstly, if I just pulled my finget out, then the gasket could have gotten kinked and the job would be sidelined. Secondly, my mum watches these videos too!! :D
@JDnBeastlet
@JDnBeastlet 3 роки тому
Nicely done, Andy. Nice save with the spacer - I was holding my breath a bit there.
@AndyManCam
@AndyManCam 3 роки тому
You and me both! Cheers John!
@craighoffman8160
@craighoffman8160 4 роки тому
Hello from Colorado. Brilliant video my UKposts FZ1 brother! Complete with finger pinching and all. I appreciate your going the extra mile! Brilliant idea about holding the rotor through the cover's port while taking it out and putting it in. Like you, the rotor in my '06 has not exploded (yet) and I just got the updated one to install. Your video will help greatly. Hopefully will avoid the pinched finger issue too ;)
@AndyManCam
@AndyManCam 4 роки тому
Thanks Craig, i do what i can! 😉. Good luck with your swap and enjoy the relaxation afterwards, knowing that your rotor will more likely last the life of the bike!
@duken4evr
@duken4evr 4 роки тому
@@AndyManCam Got her done today, the old rotor was perfect, bearings are perfect, no bleeding involved. A long Phillips screwdriver though the port to hold the rotor in and then holding the cover with my fingertips to avoid your finger pinching episode and it pulled itself together nicely due to the magnets involved. The bike pretty much assembled itself at that step like magic - hehe... Thanks again my friend!
@dudeofrude
@dudeofrude 3 роки тому
Just wanted to say thanks for the video Andy. My rotor failed on me the other day and shed it magnets 😔 But after watching this video 3 or 4 times and taking notes I've managed to replace mine myself 👍
@AndyManCam
@AndyManCam 3 роки тому
Cheers Adam. Very happy to have helped. Sorry you had to find out the hard way, but glad you got it sorted mate.
@davidlmf
@davidlmf 3 роки тому
What year bike did you have Adam
@Viktor4506
@Viktor4506 2 роки тому
Ugh!! @9:36 Felt bad for ya when the magnets on the new rotor pinched your fingers, Andy. You deserve a pint of your favorite beer for that!! Thanks for sharing your rotor replacement video with us; very helpful and informative. Cheers, Bro🍺
@AndyManCam
@AndyManCam 2 роки тому
I should have known that it was going to happen! My pleasure Viktor, happy to help!
@UseitLoseit
@UseitLoseit 4 роки тому
All good, you obviously know what you're doing. My only bit of advice thrown in, is always remember what holes the bolts came out of. Admittedly they all look the same length in this instance, but many a time I've taken covers off and found some bolts longer or shorter than others, or even different thread sizes. Don't just throw them in a heap and hope for the best when replacing.
@AndyManCam
@AndyManCam 4 роки тому
Thats a very good tip. Cheers Nick. I got lucky this time!
@jeffspears8801
@jeffspears8801 Місяць тому
Thank you brother,just completed my '08 ...smooth as silk!
@redrob5808
@redrob5808 4 роки тому
Another brilliant "how to" video from you. I've bought the gasket so I can see if mines already been replaced. Fingers crossed it has!
@AndyManCam
@AndyManCam 4 роки тому
Thanks Stephen. That's exactly how I started. But then after realising that there was ZERO chance that my '06 bike had the new rotor, I went all in! But for the tenner for a gasket, nothing to lose. Just be sure to hold it all in place through the hole and then you potentially won't have to disturb anything if it turns out that you've got the newer part. Fingers crossed and let me know how it goes!
@chargerification
@chargerification 8 місяців тому
@@AndyManCam besides the allen key, is there another 'improved" way to keep it all in the case?
@rosesmith5135
@rosesmith5135 3 роки тому
Wow very interesting issue with this bike ! I was considering buying a newer year version of this motorcycle but with these obvious design flaws I will need to continue my search ... many thanks for shedding light on this important matter !
@AndyManCam
@AndyManCam 3 роки тому
Yeah it'S a bit of a killer. It's cool that it's fixable, but 400€ for a preventative fix that might not ever be necessary is a large negative for the bike as a whole. After 2015, I think they all had this rotor installed from the factory. But that was the last year!!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
Its not that common. It really isnt.
@tkaxxdavexx6874
@tkaxxdavexx6874 2 роки тому
Firstly, thank you for this "how to" video. I live in Canada and have a 2007 R1, I decided to proactively change the rotor even though mine looked fine at 22k. I didn't see the need to replace the stator so just did the rotor. I had 3 options, $950.Cnd for OEM, or $250 for the RM or Kimpex (China Made) replacement. I called RM Stator first but they were unfortunately resistant to answer my questions, I found their customer service poor. I ordered a Kimpex brand one which looked exactly the same as RM Stator's. The rotor looked decent but had improper machine tolerances, the spacer didn't fit over the shaft - some people apparently sand it down but I didn't feel comfortable doing this, nor should you need to if machined properly. Additionally, it fit too loosely when seated in the bearing. Returned for OEM. BTW the OEM has updated this part and it does look slightly different than these Chinese knock offs. In a high HP, high RPM engine, I'd buy Japan made OEM... just my opinion. Good luck & stay safe!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
RM are the worst ones they last 2yr. Their reputation is abysmal now they never upheld warranties
@MySmallunix
@MySmallunix 3 роки тому
I was watching random videos on the Tube when I saw yours...I ordered the new rotor and replaced as well on my FZ1-N (2011). It’s incredible how a giant motor company like Yamaha didn’t make a public campaign. What can happen if the rotor explode while you drive on the highway? Shame on you Yamaha. Thanks for sharing man!
@Viktor4506
@Viktor4506 2 роки тому
Shame indeed. All the money the Yamaha company earns and they just leave their customers in the dark. Man, wth….
@bigduphusaj162
@bigduphusaj162 4 місяці тому
they did address it they started fitting the newer part within months of it being known. Its only the very early bikes that had the bad epoxy. On the 5vy R1 it got the better epoxy ones within 6 month and the full new sheathed part within a year. You want to moan about Yamaha when BMW, Ducati, KTM, Aprilia have a bunch of time bombs in them and they dont even bother upgrading the part? i mean the entire s1000rr is a heap of junk and needs everything on it redesigned to last more than 30k miles 😂 I know becaue ive had two and both melted out piston crowns on stock tune with one of them having piston 1 take a tumble in the barrel. That was then refited with a new engine on warranty, my mate bought it from me and the new engine blew up 17k miles later so he insurance jobbed it. Dont even start me on Ducati, my last ducati blew up so bad parts of its engine were in my boots. Yamaha are the best for recalls and upgrades out of ANY motorbike manufacturer and i should know, im a bike mechanic of 4 decades
@finddtime7008
@finddtime7008 4 роки тому
I bought my 09 FZ1 about 7 months ago and that's the first thing I did was this upgrade. Takes only a few minutes and it's easy. Best insurance ever.
@AndyManCam
@AndyManCam 4 роки тому
If I'd known about it, I would have done it a lot sooner too! Thankfully it seems that I was one of the lucky ones!
@nickarnold8417
@nickarnold8417 2 роки тому
Did it make any noise before you replaced it. My bottom end is making a sort of gravely noise …🤔😬😒
@AndyManCam
@AndyManCam 2 роки тому
No, mine was completely silent. The part was even still 100% intact. I just didn’t know for how long!!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
​@@nickarnold8417thats your clutch brother
@gabygg4
@gabygg4 7 місяців тому
The glue that holds the magnets started to fail on my rotor after 28k km. Luckily I was close to home so only a little bit of scratching happened to the core of the stator which was easily cleaned. I just replaced the rotor with the newer model thanks to you. Amazing video and very confidence inspiring! Thanks for making it!
@AndyManCam
@AndyManCam 7 місяців тому
Very happy to hear that you caught it before things got expensive!
@marcusFZ6
@marcusFZ6 4 роки тому
Dude, I have to say a big thanks. I've been having a few troubles with the bike and it turns out the Generator has completely shit it's self !!!!!! Basic I went for a run on Sunday and the bike died 1 mile from home. Looked like a dead battery at 9.5v when measured when I got it home. New battery installed and throws up Code 46. Checking a few things and see that the battery isn't charging. Check the Regulator/Rectifier and it seemed to be ok. Watched your video last night, 31st October. Came home from work and stripped Generator to discover lots of broken bits. Lucky for me I got this in time as all the bits are inside the stator/rotor. Looks like it's going to be expensive in parts!!!!! Can't complain on a 2007 FZ1 with 85,000km on the clock.
@AndyManCam
@AndyManCam 4 роки тому
I’m really sorry to hear that this happened to you Marcus, but very happy to have helped you get to the bottom of it! I’m many ways that’s a stroke of luck that all the bits stayed in the generator. Could have been far more expensive!!
@Andmclnpl
@Andmclnpl 4 роки тому
Congrats man, loved the video! And the washer "jumping for freedom" right when you realised it was there... lol! Fortunately everything went fine with it! Ps: little side comment. The generator of my V strom 650 2010 took the fair decision to give up while I was on the highway, driving from Naples to Florence, on a lovely Sunday. It took me a while to realise it was not just a simple battery issue, but at that point I was too far to head back home. Got to Florence charging my battery at every single gas station... and replaced the generator! Cheers man! :)
@AndyManCam
@AndyManCam 4 роки тому
Cheers Andrea. That was a close call then! Glad you didn't get any damage from the broken electro-whizzer!
@highlandriders9696
@highlandriders9696 4 роки тому
Excellent stuff mate and even a slight parody of the Charlie bit my finger video lol.
@AndyManCam
@AndyManCam 4 роки тому
Haha! I wish I'd thought of that at the time! Could have been the next youtube sensation!! :D
@raycollington4310
@raycollington4310 4 роки тому
Bonded (glued) ........ our word is our bond and small deposit secures, thanks for the education and relieved that no small parts disappeared down into the crankcase, cheers Andy!
@AndyManCam
@AndyManCam 4 роки тому
And bonded magnets are about as reliable as a verbal contract! Cheers for watching Ray!
@rossdutton9781
@rossdutton9781 2 роки тому
Thankyou for your indepth video.Ive changed my rotor ,oem. Sorted .👍
@AndyManCam
@AndyManCam 2 роки тому
My pleasure. Glad it helped and congrats on your fix! Now you can sleep better at night!
@rossdutton9781
@rossdutton9781 2 роки тому
@@AndyManCam hi buddy did you notice a different sound coming from the rotor at all.Everything fitted into place nice gasket an cover no probs .just wondering buddy.
@Viper6-MotoVlogger
@Viper6-MotoVlogger 4 роки тому
You did a fine job mate and gave yourself some peace of mind. It still boggles my mind that some random engineers thought it would be acceptable to bond magnets to the rotor 🙄.
@AndyManCam
@AndyManCam 4 роки тому
You're damned right! Ever since I heard about it I was dreading every ride in case the bike exploded! Thankfully now I can relax!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
epoxy can easily bond magnets at way faster rpm than that for decades on end. The problem is the epoxy type and the use of non-compatable oil. The upgraded one uses West Systems 105 epoxy from the marine world, wheras the failing one used 3M epoxy that although good it just doesnt like being oiled up it has less resistance to oil than the purer 105 stuff from West System. Its also noticable that the bond failure happens at the rotor side rather than at the magnet side, my own opinion of this is that the rotor surface was over polished on the places the magnets were bonded to therefore less mechanical bond. Add that to the oil deteriorating the 3M epoxy and you have a drama waiting to happen. What people need to remember though is its still a rare occurance as 5VY R1 is widely regarded as one of the most reliable motorbikes ever created. They rarely give any issues at all.
@Viper6-MotoVlogger
@Viper6-MotoVlogger 4 місяці тому
@@bigduphusaj162 👍
@DJCURRENSY
@DJCURRENSY 4 роки тому
I thought about doing this over the summer on my 04 R1... didn't... a few weeks ago BOOM... rattle noise and power cut off on the bike mid ride... looks like a easier job than I expected, thanks for the video
@AndyManCam
@AndyManCam 4 роки тому
Bugger. Sorry to hear about that. Hope you got it sorted out ok.
@DJCURRENSY
@DJCURRENSY 4 роки тому
@@AndyManCam I'll be ripping apart next weekend and ordering parts
@DJCURRENSY
@DJCURRENSY 4 роки тому
@@AndyManCam ordered parts this week, should be here today, going to knock it out this weekend and have her back on the road again. Thanks for the video again, most of the vids i've seen are half ass, no info or just cant see, pretty straight forward though.
@dazjoy4074
@dazjoy4074 4 роки тому
Hey Andy great video, aw you bastard 😂 my bike bit me, funny funny mate, prevention is always better mate, especially when it could potentially kill the engine, good job bud 👍🏼
@AndyManCam
@AndyManCam 4 роки тому
Cheers Daz! I've got scars from that encounter! Physical AND psycological!
@naresh286
@naresh286 4 роки тому
Hi Andy . Thanks for the video . Very informative as I own a fz too . Just bought the rotor . Can you pls share a link for the gasket as well . Thanks a ton again.
@AndyManCam
@AndyManCam 4 роки тому
My pleasure Naresh. I got the gasket from eBay, so should be easy enough to find one. I think the brand was Athena.
@tommykable
@tommykable 3 роки тому
hello, i like your video very much , same motorcycle, fz1 fazer 2009, 33.000km you think it's better to check, how many cases with this issue? and how is the symptoms?
@thalliumrc3981
@thalliumrc3981 4 роки тому
9:35 Lmao I saw that coming I was yelling my screen for you to watch out. Iv done that before.
@AndyManCam
@AndyManCam 4 роки тому
Haha! Thanks for trying to warn me mate! I really should have seen it coming myself!!
@teddd2009
@teddd2009 3 роки тому
Brilliant video! This completely demystifies the rotor magnet issue for me. Sorry, your bike bit you :)
@AndyManCam
@AndyManCam 3 роки тому
Very happy to have helped Ted. The finger has since healed nicely thanks. I can reach around corners now though... sideways.
@cornish_boy6235
@cornish_boy6235 4 роки тому
So glad you did this, mine failed but was still lucky as it didn’t destroy anything else apart from the bearings.
@AndyManCam
@AndyManCam 4 роки тому
That is lucky! Though even the bearings is a bit of a pain in the arse!! I'm glad mine were still good!
@cornish_boy6235
@cornish_boy6235 4 роки тому
Yeh the one in the casing was a pain to do.
@AndyManCam
@AndyManCam 4 роки тому
I really lack the space and tools for bearings in my garage, so I live in constant fear of one failing!!
@cornish_boy6235
@cornish_boy6235 4 роки тому
Andy Man Cam haha I was like that until I moved this year, my only condition to the misses was I wanted a garage, lol
@AndyManCam
@AndyManCam 4 роки тому
And too bloody right!! I gave up my private garage when we moved nearer the city centre. I’ve still got my garage space, but it’s rubbish sharing with people!! I miss it terribly!!
@NitrousShiro
@NitrousShiro 3 роки тому
Have to ask, what size torque wrench were you using when tightening down the M6 and M8 bolts?
@bigduphusaj162
@bigduphusaj162 4 місяці тому
it doesnt matter as long as its withing the wrenches torque settings. My norbar even give chart to show you how much extra you need to add for using step-ups, step downs, unis and extensions. Its barely anything at 20 lbs/ft so?
@gtipsolutions
@gtipsolutions 3 роки тому
Last year I had to replaced my stater{becase the fing glue failed on magnets, sure most know about this} on my 2006 FZ1. Well everything went smooth until install. The stater I bought via internet. Well it had a short cable...had to use only one screw to hold the rectifier. resulting in small leak that I traced to the electrical boot. any suggestion? I was thinking of maybe a type of high temp silicon. Should I back out the allen nuts and apply sauce or just apply on boot? I don't want to fuck up worse...any help would be appreciated? Also was kind of sealant sauce should I use? BGShocker Let's Ride...Fast!! ========================================= Red FZ1 2006 Full Carbon Yoshi pipe, and Air box modify =========================================
@AndyManCam
@AndyManCam 3 роки тому
See the other reply Brian. Sadly, it's about as useful as this one!
@47blackdeath
@47blackdeath Рік тому
Thank you for the awesome video! Did you had any other issues with the new replaced rotor? My mechanic told me that this is a designed fault and the issue is reoccurring due to the bad position of the rotor. Thanks much!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
the new OEM replacement has a 101 in the middle of code rather than 100 that the old part had. The new one uses a better epoxy and has an inner sheath that completely protects the stator. Your mechanic is talking bollux mate. The problem was only ever the epoxy on the magnets of the rotor. Nothing else.
@pietervanderweij4855
@pietervanderweij4855 11 днів тому
Best flyweel swapping movie of UKposts, thanks for the great video
@chong-kenglimdr8922
@chong-kenglimdr8922 4 роки тому
Hi. Great video. Do you have the part number for the gasket?
@AndyManCam
@AndyManCam 4 роки тому
Thanks very much. I’m afraid i don’t have a part number. I just searched for gasket for FZ1. I think mine was from Athena.
@NZsarge1
@NZsarge1 4 роки тому
Nice! You actually looked like you knew what you were doing 😏😁
@AndyManCam
@AndyManCam 4 роки тому
I'm a solid pretender. Fake it til you make it!
@louteix9981
@louteix9981 Рік тому
Hello my friend, just happened the same thing to me, and just have a question do I need to drain the engine oil? Thank you very much.
@MennoCaniels-ep4hr
@MennoCaniels-ep4hr 10 місяців тому
i am gonna flush it twice
@AndyManCam
@AndyManCam 10 місяців тому
If you’re worried that parts have fallen into the engine, then definitely yes. And then try to find the bits that you think you are missing, just to be sure that you got it all.
@RusticWise
@RusticWise Рік тому
Super vidéo, thanks a lot.
@AndyManCam
@AndyManCam Рік тому
Many thanks RW!
@dennywenzel6083
@dennywenzel6083 8 місяців тому
Yep! That´s what happens to my Yamaha FZ8 Fazer 2014 a few weeks ago. I was in Norway near the northcape. 3500km far from home the magnets of the rotor destroyed the stator. Now I have a completely new generator. Thanks to the Yamaha workshop in Alta (Norway).
@AndyManCam
@AndyManCam 7 місяців тому
Sorry to hear that mate. I hope it didn’t ruin the trip too much. At least now you know that it shouldn’t happen again!
@dennywenzel6083
@dennywenzel6083 7 місяців тому
@@AndyManCam Everything fine. That was part of the adventure and the repair took only 2 days. ☺️
@AndyManCam
@AndyManCam 7 місяців тому
@dennywenzel6083 Glad to hear it! Great attitude! 🤙🏼
@bigduphusaj162
@bigduphusaj162 4 місяці тому
thats just bad luck as the 2014 has the newer one in it.
@tiger98011
@tiger98011 4 роки тому
Great video, thank you! I purchased my 2011 used with 6k miles on it in 2017. I have no idea if the orig owner did this update. It looks like i can just take the screws out and take off the cover to see if it's been updated, replace the seal and reseal it together again?
@AndyManCam
@AndyManCam 4 роки тому
Hey, thanks Greg! Absolutely yes. You can take a look and just replace the gasket after. 👍🏻
@giamademedoit
@giamademedoit 2 місяці тому
@tiger98011 what happened with your rotor? Did it have the exposed magnets?
@tiger98011
@tiger98011 2 місяці тому
My initial one was the oem, with the magnets visible. I replaced it with the rmstator version.
@leespender4774
@leespender4774 2 роки тому
Hello Andy from Australia i just got a 2010 FZ1N and the first thing i bought is this updated rotor i took the cover off to change it and there was already the updated one looking back at me lol thanks to the previous owner but now i have two updated rotors haha
@AndyManCam
@AndyManCam 2 роки тому
Ha! What are the chances! Still, at least you can either get your money back or sell to another poor FZ1 owner scrabbling sound for the right part!
@leespender4774
@leespender4774 2 роки тому
@@AndyManCam Yes that is true 👍
@AndyManCam
@AndyManCam 2 роки тому
So that’s 400$ you can spend on something else cool!!
@leespender4774
@leespender4774 2 роки тому
@@AndyManCam I am going to restore her to showroom condition eventually so it will be a long term project the $400 will help
@mrrocket400
@mrrocket400 3 роки тому
hi andy. i just bought a 07 fz1 and this is stressing me out, would you say this is a must or should i leave it, i only plod about an a sunday so is it worth doing? im no mechanic by any means. so its easier for me to leave it/// thoughts please
@AndyManCam
@AndyManCam 3 роки тому
Sadly I think it is a bit of a ticking timebomb. It might never go off, it might go off tomorrow. Too many comments on this video alone from folks that have had it happen, for it to be ignorable. Sorry mate. You can change it, or you can roll the dice...
@brianwiniarski4490
@brianwiniarski4490 3 роки тому
Thanks for posting. Didn't know there was a issue. I'll have to take mine apart and see which one I have. It has 39k on it.
@AndyManCam
@AndyManCam 3 роки тому
It's very annoying. Good luck!
@stevenma188
@stevenma188 3 роки тому
Great how-to video. 1 point to make, I took your advise that "oh the washer shouldn't fall into the engine", and boy was I wrong. Washer dropped to the bottom of the oil pan. Fortunately I was able to fish it out with a magnet. Be warned, take more care when pulling the starter clutch out.
@AndyManCam
@AndyManCam 3 роки тому
Thanks Steven. Sadly 'shouldn't' isn't the same as 'won't!! Thinking about it in hindsight, I should have had the bike on the sidestand to encourage any falling debris to fall outwards!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
slide A4 paper under the rotor. Thats all you need to do.
@GOBLINMASTER409
@GOBLINMASTER409 3 роки тому
Hey, what year is your bike as I’m hearing they upgraded it after 2007 on the FZ1 and N. Great video btw
@AndyManCam
@AndyManCam 3 роки тому
As far as I know, they didn't upgrade it until 2015.
@JustSteve247
@JustSteve247 3 роки тому
Sorry one last question, could you tell me which one I need to buy for my 2009 fz1 faired please ?
@AndyManCam
@AndyManCam 3 роки тому
The same part for all years Steve. Part numbers are in the description. 👍🏻
@JustSteve247
@JustSteve247 3 роки тому
@@AndyManCam brilliant. Getting an akripovic next week fitted so I think while I'm at it I will go for this also. Again, thanks for your help. Steve
@blitzerrrrrrr
@blitzerrrrrrr 4 роки тому
Excellent video!
@AndyManCam
@AndyManCam 3 роки тому
Thanks very much! Cheers for watching!
@jaypearce6199
@jaypearce6199 3 роки тому
I have the 2008 fz1n ABS model, should I be considering this upgrade too? Thanks
@AndyManCam
@AndyManCam 3 роки тому
I think that for the sake of the 10€ gasket, it might be worth opening her up and having a look. Just read down the comments here and see how many people it's happened to!
@karta3989
@karta3989 5 місяців тому
Hi Amc. Thank you for this educational video. Could you please share a link related to where to buy this upgrade rotor from? Many thanks in advance
@AndyManCam
@AndyManCam 5 місяців тому
I bought mine from Motorcycle Spare Parts Europe.
@erikschei1481
@erikschei1481 2 роки тому
Thanks for the videos man, but now I have to do this. There is no way that I’m not going to be thinking about it as I cruise along. I have a 06 fz1 with 18.7k miles on it, and I know the last guy did not do this. I’m still deciding to do the handlebars or not. Your video on that does not make it look like a real good time lol. But I’m happy it’s there, so I know what I’d be in for. Thank you again for the videos, always super helpful. Stay safe out there.
@AndyManCam
@AndyManCam 2 роки тому
I know that feeling! As soon as ever people had told me about it, i expected that every ride was the one during which the engine would implode!! Yeah the bars was a challenge and a lot of effort. Think long and hard!!
@erikschei1481
@erikschei1481 2 роки тому
I just replaced mine. I also had to put it in 6th gear to get it on, and fish my finger back there to get it in. On another note, I have had a hard time finding a video for adjusting clutch engagement for fz1. After I put my new levers on and adjusted tension at the lever, my engagement is right up against the grip. Which is not ideal. I’m wondering if I’m going to have to pop up the tank and adjust it there as well.
@AndyManCam
@AndyManCam 2 роки тому
Nice one. Sadly I’m afraid so, yes. Luckily the tank is pretty easy to free up and it’s hinged at the back too, so you can prop it up like a car bonnet.
@erikschei1481
@erikschei1481 2 роки тому
@@AndyManCam I’m dumb, i just turned it some more and it’s perfect. Thank you for the help on all this stuff. I’ve been able to watch one of your videos on pretty much everything I’ve done to the bike this past week and a half. She’s ready for the summer. New rotor, spark plugs, new chain/rear sprocket, new front/back tire, braided brake lines front/back, new levers, heated grips, new horn, new brake pads, oil change/filter, and coolant flush.
@AndyManCam
@AndyManCam 2 роки тому
Glad to hear it. No trouble at all. Sounds like you’ve got more new bike than old! Happy riding!
@nseryoussef3080
@nseryoussef3080 3 роки тому
The stator that you used in your fz1 does it work also in the Yamaha fz8 ?? And if it works plz just send me the link of the shop to buy the same one
@AndyManCam
@AndyManCam 3 роки тому
No idea I’m afraid. Maybe ask in the forums.
@atifwatwat
@atifwatwat 3 роки тому
Hi I’ve got 2009 FZ1N dose that year model still have the old roter cup ?? Please help I’m worried
@AndyManCam
@AndyManCam 3 роки тому
I think that they all had it until 2015 I'm afraid.
@jreberanlc
@jreberanlc 2 роки тому
Watched the video - ordered a rotor but could not get an oem one - took old out (looked fine, however, the new one was def notwhere near as good quality and did not fit - had to put old one back in! Not happey - but good video - thanks.
@AndyManCam
@AndyManCam 2 роки тому
Sorry to hear that Julian. But yeah, i wouldn’t bother with anything other than an OEM Rotor. Anything else would likely be swapping one possible problem for a new one! Hope you get it figured out mate.
@aspectcarl
@aspectcarl 4 роки тому
Yep did mine a few months ago👍
@AndyManCam
@AndyManCam 4 роки тому
Congrats! then you likely feel as smug as I do now that it's done!!
@Satoshi_Nakamoto999
@Satoshi_Nakamoto999 4 роки тому
Thank you from Poland :)
@AndyManCam
@AndyManCam 4 роки тому
Many thanks to you from Germany!
@christianweller4288
@christianweller4288 4 роки тому
Top tip... remember wooden clothes pegs?....Broken in half they make very useful prising wedges for aluminium covers. Also a strip of wood across the alternator before replacing the cover prevents the.... "clap" (fnar-fnar) as the cover goes back on. Still I doubt if you'll do that again.
@AndyManCam
@AndyManCam 4 роки тому
That's a great tip! Now why didn't I think if that!? Of course, I haven't seen a wooden clothes peg for several years and wouldn't know where to get some!! :D Hopefully I'll never have to go in there again anyway!!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
or get proper prying tools
@fishyvishy
@fishyvishy 4 роки тому
Hiii mate before you installed you face power loss problem or after replace it is sovled ? Plz anwere mate thanks
@AndyManCam
@AndyManCam 4 роки тому
Hi! There was no difference in power before or after fitting the new rotor. Just less chance of it exploding!
@JustSteve247
@JustSteve247 3 роки тому
Hi. Hope your well. I have an 09 fz1 is there an issue with that year please? Steve
@AndyManCam
@AndyManCam 3 роки тому
Hi Steve. I'm afraid it seems that every year from 2006 - 2014 has the potential for this rotor problem to rear it's ugly head, as the redesigned rotor wasn'T implemented until the 2015 bike. Might be worth a check.
@JustSteve247
@JustSteve247 3 роки тому
@@AndyManCam I appreciate the heads up Andy. Many thanks. Any tips on resolving the the snatchy gears? I find mine to be quite clunky if that makes any sense. Steve
@MotoRic
@MotoRic 4 роки тому
Thanks Andy, I’ve ordered it for my Fz8 now. Most Fz8 owners have reported that it goes bang at around the 30k mark and I’m currently at 27k ,don’t want to test my luck !!
@AndyManCam
@AndyManCam 4 роки тому
I can fully understand that! I was going to run the clock on mine but caved after hearing about the giving up as little as 15,000 miles in!! 😳. Annoying, but also satisfying to know that it’s a potential problem avoided! Hope your swap goes well mate.
@KAShuACE_8807
@KAShuACE_8807 4 роки тому
Wow
@KAShuACE_8807
@KAShuACE_8807 4 роки тому
I'm almost at 14k
@mrwiggy8593
@mrwiggy8593 4 роки тому
Hi Mr mancam. Any idea what year the upgraded rotor became standard on the fz1n? I Can't find any info anywhere. Also did you have to retune Your engine after swapping the muffler from standard? Your channel is excellent to mate. Best fz1 stuff on UKposts. Keep up the good work
@tentacleprty
@tentacleprty 4 роки тому
Only the last year 2015 has the new rotor from factory.
@mrwiggy8593
@mrwiggy8593 4 роки тому
@@tentacleprty thanks for the reply. looks like I should buy one soon as I can afford it . I got a 2010 model. hard to believe yamaha would leave a duff rotor in their bikes for so long. Are there any signs the rotor is on the way out or will it just explode? Cheers
@AndyManCam
@AndyManCam 4 роки тому
From what I've heard, it varies. Some have reported a whining sound, some a rattling, some instant failure with bangs and crashes and some just that the bike stopped charging and when they looked inside, it had fallen to pieces. Obviously all cases with varying degrees of damage depending on how far the magnets had wandered and whether or not they had broken up and gotten in to the bearings. I saw it as an expensive and annoying fix (Thanks Yamaha).But it was half the cost of what a destroyed generator would be and a fraction of the cost of stripping the whole engine down to pick pieces of exploded rotor magnet out of the cylinders! Not to mention the potentially ruined tour and the recovery costs.
@akumarrxz
@akumarrxz 3 роки тому
Great video mate.I am just wondering,I heard the Fz1 engine came from the R1(2004-2005) models.So Why those R1s never had any router issues?Or Why R1s are not infamous for this issue? Cheers.
@AndyManCam
@AndyManCam 3 роки тому
Many thanks Anish! I'm pretty sure that if you were to trawl the R1 forums, there would also be plenty of people that have had the same problem. I didn't know about it on my bike until I started looking for it. And then I found ENDLESS cases where peoples bikes had imploded!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
The original R1 5VY had the bad one for only 6 months before the better epoxy was used im pretty sure the other bikes with it got it a year laster. Also your block isnt 100% the same as the R1 as yours is more like the jetski block with a diffent head. The R1 block has bigger plugs and is generally better made.
@OlivierABOLET
@OlivierABOLET 2 роки тому
Somebody can tell me the size for the allen wrench please ? (For the plot) Thank you so much
@harryw9598
@harryw9598 7 місяців тому
top tip, screw in some thread rods, and slide on the cover.
@AndyManCam
@AndyManCam 7 місяців тому
Great tip, cheers!
@ShawnMartinNCBIRDMAN
@ShawnMartinNCBIRDMAN 2 роки тому
What clutch/brake levers do you have?
@AndyManCam
@AndyManCam 2 роки тому
I think they were V-Trec, both from motea.com 👍🏻
@ShawnMartinNCBIRDMAN
@ShawnMartinNCBIRDMAN 2 роки тому
@@AndyManCam ok, they looked a lot like my MZS. I've done a few things over the last few years to my 2012 FZ1. I ordered a replacement rotor that's on it's way now. Preventative, I've had no issues with stock yet. ukposts.info/slow/PLM1U9I2fOqzXYHj4V3tKcV392B_y1E3Cy
@GoLdxrockyHD
@GoLdxrockyHD 4 роки тому
Have any idea where I can buy those "cush rubbers" when i disassembled my 07 r1 i found that one of mine was missing.
@AndyManCam
@AndyManCam 4 роки тому
No idea I'm afraid. I guess ebay would be worth a look. Maybe a breakers yard? Or maybe even give your local Yamaha dealer. a call?
@logannewcome
@logannewcome 4 роки тому
If it's missing I'd be more worried about where it went...
@GoLdxrockyHD
@GoLdxrockyHD 4 роки тому
I ended up finding them on a site online, but I found the piece that was missing in my oil pan. I'm just now getting to putting the bike back together! I had to disassemble the exhaust system and drop the oil pan. It destroyed my stator as well, so I had to disassemble the air box as well. Fun!!!
@GoLdxrockyHD
@GoLdxrockyHD 4 роки тому
@@AndyManCam appreciate the reply :)
@GoLdxrockyHD
@GoLdxrockyHD 4 роки тому
@@AndyManCam I called Yamaha and they were no help to me wouldn't even give me to the time to explain my issue.
@bccapone837
@bccapone837 2 роки тому
Great video , what rotor did you buy and have you got a link please 👍🏼
@AndyManCam
@AndyManCam 2 роки тому
The part numbers are in the description. Give them a Google and I’m sure you’ll find somewhere near you.
@goansunborn
@goansunborn 7 місяців тому
Excellent!
@AndyManCam
@AndyManCam 7 місяців тому
Cheers!
@mikeninjitsu4665
@mikeninjitsu4665 3 роки тому
How about the possibility of the frame cracking on at least some of the earlier Gen 2 FZ1's? Any thoughts on that or fixes or whatever? TIA
@AndyManCam
@AndyManCam 3 роки тому
Unfortunately the only fix for the cracked frame problem is to have the frame rewelded or replaced. Another triumphant moment for Yamaha quality control and customer services 🤦🏻‍♂️
@bigduphusaj162
@bigduphusaj162 4 місяці тому
​@@AndyManCamYou do know Yamaha have the most reliable bikes yeah?
@lucianosalvi9459
@lucianosalvi9459 2 роки тому
AndyManCam lamentablemente es una falla de fabrica que yo no sabia ya que es mi primera moto en 4 cilindros compre una FZ8 y al mes de uso me paso esto, gracias a tu video supo lo que era, te lo agradezco, pero quiero que me saque las dudas, vos sacaste el carter de la moto y cambiaste el aceite, la duda es que si se desparramen los imanes o no se desparraman por el motor, porque al fondo del motor tiene el chumador que envia el aceite al filtro.
@AndyManCam
@AndyManCam 2 роки тому
That's a real shame. Sorry Luciano. I agree that if the rotor has failed, it's a good idea to take things apart and remove all the pieces. Such a pity that Yamaha did this to it's customers and never attempted to fix it for them.
@trevorjones9706
@trevorjones9706 2 роки тому
Hi where did you get your rotor upgrade from. Thanks in advance.
@AndyManCam
@AndyManCam 2 роки тому
I’m really sorry, i honestly can’t remember and i can’t find any info about it. But i pretty much just googled the part number and went for the cheapest brand new item, from a reputable looking seller.
@nickarnold8417
@nickarnold8417 2 роки тому
Did yours make any noise prior to replacing. The bottom end of my motor has a gravelly sound
@grahamabernathy8892
@grahamabernathy8892 2 роки тому
Hello, did you drain your oil before doing this? Thanks!
@AndyManCam
@AndyManCam 2 роки тому
Nope. No need. Everything is drained into the sump.
@jroach90
@jroach90 3 роки тому
Hi Andy, little late to the game here. Any idea on what production years are in question? I’m on a 09 plate FZ1-S Cheers 👍
@AndyManCam
@AndyManCam 3 роки тому
AFAIK it was only fixed in 2015.
@georgetech380
@georgetech380 4 роки тому
If we want only to to do inspection to the magnets and not replace we don't have to pull out the rotor are we? if we removed only the stator cover the rotor the back washer and the rest stays in place is that correct?
@AndyManCam
@AndyManCam 4 роки тому
Absolutely right. You can just have a look and check all is well, then bolt her back together! You will need a new gasket though.
@georgetech380
@georgetech380 4 роки тому
Andy Man Cam Many thanks
@AndyManCam
@AndyManCam 4 роки тому
My pleasure George. Hope you get it sorted.
@georgetech380
@georgetech380 4 роки тому
Andy Man Cam Thanks is for a friend ... I have FJR 1300 iam fine lol
@DrDonatoDONI
@DrDonatoDONI 4 роки тому
Seems that my bearing on the cap (outside piece ) is giving me the grouling sound... Any idea how to change that bearing??
@AndyManCam
@AndyManCam 4 роки тому
I'm afraid not. MAybe you'll just have to have it pressed out and a new one pressed in.
@DrDonatoDONI
@DrDonatoDONI 4 роки тому
@@AndyManCam old vas hammered out... For the new one.. i iv put the bearing in a freezer and heated the metal piece with a heat gun.. slided right in... Same process with the cover and metal piece...
@BucketWheat
@BucketWheat 4 роки тому
What year model was the 'up-dated' rotor used..? I have a 2012 model. Do I need to up-grade my rotor? I ride pretty aggressively -- including occasional Track Days. And I sure don't want to be 'up in the mountains' and have something come apart!
@marcelinhayden6441
@marcelinhayden6441 4 роки тому
Bad. I have the 2012 black and white. Stater went bad at 35k miles. Warranty fix for free but I believe they used an old school bad design part.
@tentacleprty
@tentacleprty 4 роки тому
2012 has old design. Only 2015 has new one from factory
@AndyManCam
@AndyManCam 4 роки тому
Awesome stuff from Yamaha, Marcelin. Replace a known bad part with another known bad part, purely because they've clearly got thousands of them sitting on shelves!
@videovaccser
@videovaccser Рік тому
Hello, anybody knows that which years of manufacture are affected? I have a 2015 FZ8n. Can I check it by VIN?
@AndyManCam
@AndyManCam Рік тому
As far as i know it was from the bikes made in 2015 that were sorted. But some 2015 registered bikes were actually made in 2014. Musst be some way to find that from the VIN.
@denekaraus8592
@denekaraus8592 4 роки тому
Did the job in the last month. Your video and another both say unplug the cable to the bridge rectifier. It's unnecessary. Having a jack stand set to the left of the cover gives one a place to sit the stator/cover with physical support, and the cable helps stabilize it.
@AndyManCam
@AndyManCam 4 роки тому
I think that I would always rather just disconnect either the battery or the rectifier. If you've accidentally left the ignition on and then short a tool across the coils then it could be an expensive and annoying cock up. Probably not, but for the 20 seconds it took to unplug the rectifier, the peace of mind that 100% NOTHING can go wrong was definitely worth it! On the other side of the coin, the cable seemed like it was more than man enough to support the stator/cover for the few minutes it took to the job.
@hunterjohnson2230
@hunterjohnson2230 3 роки тому
Thank you for the helpful video. I found a new stator from rm stator and has very good reviews for the bike. How would it compare to oem? Money is tight and oem one is 400$ as opposed to the 200$ rmstator
@AndyManCam
@AndyManCam 3 роки тому
Happy to help Hunter. I'm afraid I couldn't possibly say anything with regard to the aftermarket stator. No experience I'm afraid.
@jhernandez77794
@jhernandez77794 3 роки тому
My current predicament as well
@hunterjohnson2230
@hunterjohnson2230 3 роки тому
@@jhernandez77794 I went oem. To manny hit or moss reviews on the rm stator
@TALEX-07
@TALEX-07 Рік тому
Do we know approximately that the new rotor assy, how much wil last?
@bharadwajbungab
@bharadwajbungab 5 місяців тому
Very helpful video mate! Now that I've acquired the skill to do it myself at home, I'm confused about choosing the right part. OEM one from Japan or the one from RM Stator?
@AndyManCam
@AndyManCam 5 місяців тому
I personally went with the OEM part, as I knew that the fit and finish would be the best.
@bharadwajbungab
@bharadwajbungab 5 місяців тому
@@AndyManCam Thanks for the reply! Me too going with the OEM one
@AndyManCam
@AndyManCam 5 місяців тому
@bharadwajbungab My pleasure. Hope the swap goes well.
@bigduphusaj162
@bigduphusaj162 4 місяці тому
​@@bharadwajbungabdont go near the RM one its worse. The Yamaha replacememt parts are all fine they use the better epoxy now.
@raalexander8708
@raalexander8708 3 роки тому
The magnets broke on a friends bike and on mine as well, we fished them out out the oil pan and changed the flywheheel, they work great now
@AndyManCam
@AndyManCam 3 роки тому
That's a lucky bullet dodge there then! Great work!
@raalexander8708
@raalexander8708 3 роки тому
@@AndyManCam usually most pieces of magnet willll remain in the oil pan and some will get blocked by the filter, after that happens it’s impossible to ride it until you change the flywheel
@AndyManCam
@AndyManCam 3 роки тому
In a best case scenario! Sadly I've heard too many cases of even a small piece of a magnet NOT harmlessly landing in the oilpan and destroying many internals of the engine on it's little tourist trip of the inner workings! Seems you were both very lucky, but that doesn't mean that your experiences were the only possible outcome.
@mrcintheuk4641
@mrcintheuk4641 4 роки тому
Excellence as standard from you. Question: Are you supposed to torque an item twice? I thought the second time you do it, it gives a false torque setting, which is why they all tightened up a bit more.
@AndyManCam
@AndyManCam 4 роки тому
Thanks MrC. That’s quite possible. Though my thinking was that once all the bolts were tightened, the first ones to be torqued had now been relieved of some tension by the later tightened bolts. Like tuning a guitar you tune the first string, work through the other five and now the first one is out of tune because the others have been tightened and taken up some of the slack. I’ve been wrong before though!! 😂
@YeetxBoi
@YeetxBoi 2 роки тому
as a technician that has a peculiarity about torque specs I would say either method is fine. The important part is to go slow close to the torque spec and do not go past the point it clicks.
@AndyManCam
@AndyManCam 2 роки тому
Of course. In German they have a saying „Nach fest kommt ab“ which means that after tight, comes off!
@bigduphusaj162
@bigduphusaj162 4 місяці тому
​@@AndyManCamyou dont re-torque sequenced parts, the original torque figure is given as it equates to all the fasteners backing off as the gasket squashes. All you are doing is over squashing the gasket if you re-torque. I mean the torque value is so low you will get away with it but if you do that on camshaft half clams or the likes you will mess your engine up for defo. You can snap a camshaft in half re-torquing when its already been torqued up or if you dont sequence correctly. Trust me, the most expensive one i messed up was a sierra cosworth RS500 block (think its called the 205 block it has bigger block plugs the RS500 engine over the normal YB) and cost me another £500 for the OEM cam it snapped. I knew not to do it but i thought i seen one of them move as i done the opposite end.
Заменили роторы генератора на FZ1
13:12
Kondrakov MB
Переглядів 20 тис.
Changing Handlebars, Yamaha FZ1
35:12
AndyManCam
Переглядів 63 тис.
Помилка,  яку зробило військове керівництво 🙄
01:00
Радіо Байрактар
Переглядів 450 тис.
Мы играли всей семьей
00:27
Даша Боровик
Переглядів 1,1 млн
ЧТО ДЕЛАТЬ, ЕСЛИ НЕ ХВАТАЕТ ДЕНЕГ НА ВОССТАНОВЛЕНИЕ ТАЧКИ?
47:52
FZ1 Video Tutorial - Generator Inspection
8:12
Patrick McCurry
Переглядів 55 тис.
Why you Should NEVER RIDE an Orange County Chopper
27:20
Bikes and Beards
Переглядів 3 млн
Downpipe Replacement on Yamaha FZ1-N
13:56
AndyManCam
Переглядів 22 тис.
Yamaha R1 vs MT-10 vs FZ1 | Inline-4 Cylinder Sportbike Showdown
14:06
Focused Garage
Переглядів 34 тис.
Norway By Bike #10 - Crashed AGAIN! 🤦🏻‍♂️
17:05
AndyManCam
Переглядів 12 тис.
Yamaha FZ8 przegląd, check engine, rozrząd, synchronizacja, magneto.
13:24
Genetyka Motocykli
Переглядів 7 тис.
Вот это подстава 😂 #юмор #смех #смешно #приколы #пранк
0:30
Мокрые шутки | Gazan и POLI
0:21
Gazan
Переглядів 1,8 млн
Осиное гнездо у себя дома
0:27
ЛАЙФСТОРИ
Переглядів 4,8 млн
ТАК ДОБЫВАЮТ ДЕЛИКАТЕС (@lepetitmoulier - TikTok)
0:16
УХИЛЯНТ😉
0:25
Prime Pravoqator
Переглядів 144 тис.