Man with good patience！

My fav youtuber! Man you helped me a lot thanks!

Hello golf Wagen!! It's possible using VCDS 18.9 for solving this problem?

Thanks man... i did it on Passat B6 and it works 👍

Thank you very much you were very helpful

You help me a lot, thanks !! I own a 2011 Tiguan 2.0 Turbo.

Hi guys👍, your content is amazing. I have a steering issu( feels very soft and does not give back any feedback from the road since) with my golf 6 GTI since we retrofit bi-xenon headlight. Is it possible to get in touch with you in any form? Thanks! 👍

Accidentally broke sensor while replacing ignition switch. New sensor needed initialized. This worked like a charm! Thanks !!

Thanks, worked a treat.

Thanks u my friend U help me so much

i have 00778 g85 code but the steering wheel lamp is not lit, mine shows esp light next to abs, i recently fitted new lower arms both sides and the steering wheel is maybe 5degrees to the right of centre. will tracking the car resetting the steering wheel to centre clear the code?

Very very beautiful video. Thank you for this video . ❤❤❤❤❤❤❤👍👍👍

Hi, I replaced my Steering rack, but it is still very stiff and displays a steady light on the dash. What should I do? it's a Passat B6

thank you very much. You're the best.

Hi I have the same problem and I replaced the steering wheel angle sensor but I still have issues and could you advise please? Thanks

Do you have to do this while the car is in motion?

I have seat leon ..i put 060 in the group but does not work ..is there any special code for this probleme

Well, my power steering stopped working after a crash where the steering wheel airbag went out, I am wondering if I am getting this fault because the battery was unplugged for a looong time (also the fuse for power steering pump was “tore in half”, so I hope it did not short out or the airbag explosion did not damage some electronics in the steering wheel…

Thanks for the video. My A5 GTI has a faulty wheel speed sensor in addition to the exact problem you show in this video. Will this procedure work with the faulty sensor or must I replace it first?

My golf 5 2.0 BHY is showing red light on the cluster n before was orange today is very hard to turn any help pls

Do you need the full version of vcds and the real cable to do this or can it be done with the cheap on off eBay and vcds lite? Thanks

So thanks, i almost gave up, but finally i made it,

Would you know why my traction control light dosent light up on the dash when I turn ignition on even if I try to disable it it don’t come on at all please help

Can I do this on my vw eos, because my steering wheel doesn't turn both left or running right it's very hard to turn

Taky mi to svítí,může to být i špatnou geometrii?servo se zdá být v pořádku.

Esses codigos dao para seat ibiza 6l amigo ?

Thank u so much bro

Tnx for help bro!❤

Good work

Where you find these number 40168 how can I found

hello i wanted to ask you i have a problem with the power steering when i bought it I had a yellow steering wheel light and the same yellow slip but the servo worked normally it was put on diagnostics and i got the code 00778 i tried to change that little sensor underneath steering wheel and tried to drive it a little and nothing, so I changed that big sensor that is in the steering wheel and after that the steering wheel became heavier and the steering wheel sometimes turned into a curve and the lamps still shine I don't know what to do

Red steering signal means have to change all the sensor set means steering angle sensor or any one of them

Congratulations on your channel. I have seen all your videos! I have a golf 5 and today I changed the steering wheel to multifunction and the steering head to highline. Everything works, the coding was done but the only problem is that the steering wheel light doesn't turn off with anything and the steering wheel is heavy because the electric assistance doesn't work. I did a basic setting and it takes values ​​on the indicator changes in the corresponding field in the vcds but with nothing it doesn't turn off and it gives the error: 02546 - steering limit stop 005 - no or incorrect basic setting / adaptation And when the adjustment is complete, this error goes away and while the steering wheel light with orange color on the dial continues to stay on , then throws the error: 02546 - steering limit stop 003 - mechanical failure. I went to a local garage and while doing the basic adjustment the light won't go off and the steering is still heavy. He told me that there must be a problem in the steering rack. Is it possible? can you tell me your opinion? Thank you very much

Thank you 🤩

Hello,teacher (BMW 7 series ce9401 )what is roung whit it? please help me.

It works on an SEAT Ibiza car ??

Had the same problem with my caddy after retrofitting cruise control i followed your video but when I went on basic settings i turned it on and solved the power steering problem but for some reason the horn is not working any idea where would be the problem because when I put the old control module it works but when I change it to the new one it stops working . Any advice why? Thank You

Mulțumesc mult

Hi, access code is not coming up on my vcds

Super good

best regards I have a passat 3c 2006 and I have that dtc sensor g85 I have given the settings and nothing changes the g85 sensor and nothing follows the dtc at times turns off the brown guide but returns dtc what can I do. when I start the car it turns red, it turns yellow and then the fixed code remains

Thank you! ❤❤❤❤❤😊😊😊

Hell sir I am from India and I have a Skoda Laura 1.9 tdi pd car. This car has been completed 200000 km and still run like new. I want to know how to care my unit injectors for more life. Because this engine has been discontinued from India.

When I got to basic settings channel 60 and turn the wheel the value doesn't change, it just reads "0.00" Does this mean the steering angle sensor needs to be replaced?

Haw for touran 1.9 HDi , longuage french please

Thanks

I dont get it. I did the same but not working. Same codes and values, Horn, airbag are okay. Help

Do you need a vcds or can you use an elm325 mini

hello, please what's the code 40168 . I have a 1.4tdi 2007 polo shirt

hello I have default 00778 on my golf 5 but no indicator light on the dashboard, do I have to recalibrate it to zero too ??? THANK YOU

I have had a G85 defective code that I am trying to clear and a failure to calibrate. I also have an ESP light on that will not change. I got a new wheel sensor and replaced it and have followed the procedure here. No joy though in clearing the code. I have a valid copy of VCDS and cannot seem to get it done. Suggestions?

Says error group 60 not available ?

I just changed the steering wheel module from BC to CH, and have this hard wheel issue, I tried the left and right without VCDS and no luck

Doesnt work for my golf 2008 :/ am i doing something wrong? Coding II 40168, basic settings, 060, full right 5s, full left 5s, drive less than 20kmh...and nothing

Where did you get the software from and how much is the software

Hi i have this light on after changing steering wheel module i got one from ebay when i try to go to basic settings it says error and m block 60 isn't available plus where do i get the coding from my old module to put in the replacement it doesn't give any long coding when i go into this module

👍

Did anyone find a solution? Im trying it for a month and nothing happened.

Hello mate. I changed the sensor, but I can't seem to remove this error. It looks the same as yours. The customer bought the sensor on AutoDoc, so Im not sure if its original or can read it. So I have to questions: 1. Does it affect it if its original or not? 2. How do I know if the sensor is working at all?

Thank you, thank you very much. It worked for me!

In my case security access code was 31857, procedure worked fine at first try. 40168 was also accepted though, but turning wheel all the way left & right like 20 times didn’t do anything. At least I got big muscle now 😅

Error when I write 060 ??

So you just have to keep trying the basic setting with or without coding password 40168 - AMAZING!! LOL

I want a solution to this problem

on my golf i had 00778 - Steering Angle Sensor (G85): No or Incorrect Basic Setting and i needed to adapt the sensor to the ABS

Code 00573?

You should to do test drive because if the car is stopped it does not take the calibration

Peace, is there a danger if we don't put it out

Działa w audi a3 8p. 2003r. Grupa 060

Toto robí po odpojení baterky, vôbec netreba diagnostiku, len vytočiť plný rejd do oboch strán a ísť sa previesť a zmizne samo, už som to robil na viac autách. Ono si to musí overiť nie len natočenie volantu, ale aj dáta z jednotlivých snímačov ABS, potom chyba zmizne sama.

Štvrt otačky do prava , štvrt otáčky do lava, plny do prava 3 sekundy počkaš!!! potom plný do prava 3 sekundy počkaš !!!vyrovnať kolesa a nasledne sa rozbehnuť hotovo !!

How about G269 steering torque sensor?

man you have to lead and it will disappear and I had this problem

Electrical Steering Wheel Warning Light!

Ahoj, vcera som presne toto robil. A som ani za ..... nevedel urobit. Nechapem preco. Presne g5 ka.

U need to play and drive...when u park the car with back it's solve , on a straight parking and play în parking, and it's solve whitout vcds.

Bit g269

I did all of this twice, Light still on , something is wrong for sure.

Problem g250

The fact that 140 thousand ++ have seen this video.... VOLKSWAGEN WHAT ARE YOU DOING? shitty shitty components. I'm here for a reason too.

Millage on vcds over 300k milles but on MFI only 200k milles, wtf😂

Traduction svp 😪

Vreau explicat în limba română

Hai

Hey, j'avais le même défaut, passe voir mes videos 👍🦅😉

Data viitoare când umblați la km sa ii faceți și în ecu... 😂

Turn on car wait 5 seconds ... Turn staring wheel all the way to the left wait 10 seconds ... Turn steering wheel to th right wait 10 seconds and then come back to straight the steering wheel will be recalibrated and the light will go out

Bosanac

No one is answering any of the comments 👎🏼

You have 320000 km 😅😅😅

E fake. E taiat clipul. Nu spun ca metoda nu este buna, este buna dar el a taiat clipul.

hi pleasure stafano ... I on my mk5 I installed multifunction steering wheel golf mk6 gtd ... steering unit with code ch ... ring code c & cable airbag 1k .... tacho full fix but blocked for now, aspect cofifica immo ... now I have hard steering and steering wheel controls not working ... how do I code everything with vcds ??? can you help me with a procedure ??? thanks and sorry translation I use google ... my mail hgt88@tiscali.it .. ..thank you very much and a very valid channel salve piacere stafano...io sulla mia mk5 ho installato volante multifunzione golf mk6 gtd...centralina sterzo con codice ch...anello codice c & cavo airbag 1k ....tacho full fiss ma bloccato per ora,aspetto cofifica immo...adesso ho sterzo duro e comandi volante non funzionanti...come codifico il tutto con vcds???puoi aiutarmi con una procedura???grazie e scusa traduzione uso google...mia mail hgt88@tiscali.it....grazie mille e canale validissimo

If you get editing skills you would have more followers and learn how to do it before you recorded

This video should be deleted

👍