Turbocharged SEE THRU ENGINE on EFI and Nitromethane (FINAL EPISODE)
Переглядів 655,996
День томуIn this episode of the see-through engine I attempt to blow the engine up yet again and finish where I left off in episode 7.
I had nothing but sensor pick up problems in episode 7 due to electromagnetic interference from the high spark energy of the ignition coil that I used so I had to cut the episode short.
This is the grand finale of the see-through engine series for See thru engine V.1 and more than likely the last episode with this particular engine, it may make a cameo appearance here and there.
thanks for your support and thanks for watching through the entire series.
this one is a pretty long video so please find the program guide below.
0:05 Intro
0:43 Changes I Made
1:58 1st Test Run
3:41 Not Starting
5:23 2nd Start Attempt on the new setup
6:25 1st blow-up Attempt (gas)
10:20 2nd Blow-up Attempt (gas)
13:45 3rd Blow-up Attempt (Nitro)
14:54 4th Blow-up attempt (Nitro)
See Thru Engine Series Playlist: • See Through Engines
↓↓All Previous Episodes↓↓
E.1 • See Through Engine - 4...
E.2 • See Thru Engine Runs T...
E.3 • See Through Engine (S1...
E.4 • See Through Engine on ...
E.5 • See Thru Engine on Tur...
E.6 • See Thru Engine on New...
E.7 • See Through Engine on ...
Big thanks to Briggs & Stratton: www.briggsandstratton.com
and DIY auto tune AMP EFI: www.diyautotune.com
↓↓Social media Links↓↓
🐦 ► Twitter: / warpperception
👍 ► Facebook: / warpperception
◙ ► Instagram: / warped.perception
☢ ► IMDB: www.imdb.com/title/tt5548028/?
I sometimes post things early or post previews on FB and Instagram so if you like that sort of thing give them a visit.
Please leave any opinions suggestions or comments Below and don't forget to check out our other videos and subscribe, Thank you.
Watch this in 4k when possible, it looks incredibly awesome !
Written and Directed by: Matt Mikka
Carbon 12
www.c12.tv
Produced By: Carbon 12
Directed By: Matt Mikka
@NewMind 4 роки тому
What an incredible series! Really enjoyed how you intuitively and visually connected reality with the mounds of theory. Great job!
@WarpedPerception 4 роки тому
Thank you! BTW I'm going to send you a viewer request very soon.
@thegadgetbuilder4268 4 роки тому
The slow motion filming was amazing. I just used the same type engine for a similar but different project which I just put on youtube.
@nikkiarcand4135 3 роки тому
@@WarpedPerception it would be cool to see it run on methanol. It's a cooler running fuel might get some longevity.. maybe ?
@larry800s 3 роки тому
Cornal Angus snl
@richardwhitaker4148 3 роки тому
Should've of raffled off the heads that went bad.
@ProjectFarm 4 роки тому
Those Briggs & Stratton engines are nearly indestructible! Great job and definitely the BEST production quality on UKposts!!
@WarpedPerception 4 роки тому
Thanks, I got to get one of those predator engines in my hands soon !!! Lbvs
@cutthroat399 4 роки тому
Two of my favorite UKpostsrs know each other. You guys show make a crossover video!
@backwoodsjunkie08 4 роки тому
I always loved to race Briggs 5hp at the kart track! I knew some guys in the unlimited class that we're getting 18hp out of the blocks! Lol the only stock part of the engine was the block... And even then "stock" was a pretty subjective term
@TheCelltek 4 роки тому
Just like a TIMEX, "It takes a licken and keeps right on a tickin"
@TheAshlec 4 роки тому
Warped Perception would have been nice to put the original head and sparkplug back on to finish off the engine. And see what actually fails not just the plastic head! One more episode??😬
@dishsoap1 4 роки тому
I’d like too see a see-thru 2 stroke engine.
@WarpedPerception 4 роки тому
It is coming!
@Tuber360904 4 роки тому
dishsoap1 damn ask and you shall receive lol
@mr.engineear0987 4 роки тому
dishsoap1 good suggestion but 2 stroke wouldn't be as fun as the 4 stroke
@dishsoap1 4 роки тому
Mr.engineEAR09 I think seeing the scavenging process in slow-mo would be worth it. I’m glad it is in the works.
@mr.engineear0987 4 роки тому
dishsoap1 good point man 👍
@nitro_rc_dude8158 4 роки тому
Do a engine teardown. Would be awsome to see the inside of it after all of that.
@WarpedPerception 4 роки тому
Ok that's a great idea, I will have to do that on my personal channel. I need to clean it up for my exhibit anyway.
@dylanyates6331 4 роки тому
I think the best part about this is the problems you ran into are legitimate problems the automotive industry ran into when they started. Really getting back to the basics
@michaelpressman7203 Рік тому
Difference is budget constraints
@Fabio.-. 4 роки тому
Try using a regular head and see how much power you can get
@AiOinc1 4 роки тому
He did that last episode
@idahoshoter 4 роки тому
He did 11 torq and like 13 hp
@WarpedPerception 4 роки тому
Here you go ukposts.info/have/v-deo/cZh-oqKwgpB92Hk.html
@schuchdan02 4 роки тому
You should have added nitrous oxide if you really wanted to blow it up good!!
@kd7cwg 3 роки тому
@@schuchdan02 did that to a push mower years ago. It survived 🤣
@robertschmidt7625 4 роки тому
Regardless of size or HP, Briggs & Stratton engines are tough, reliable, and virtually indestructible. This engine however deserves an A+ in quality! Best in the world! #1!
@deleterium 4 роки тому
8:08 With high speed camera and transparent air intake you can adjust optimal timing for fuel injection! Note that it was not injecting at the same time the air flows into cylinder.
@WarpedPerception 4 роки тому
You're right it was not, because the sensor is already shot so the ECU is just taking a guess at the RPM at this point
@michaelpressman7203 Рік тому
It ran
@Dubz0408 4 роки тому
Unless youre ending this series with something spectacular in mind, like a turbo see through rotary, I want to see this with *MOAR BOOOST!!!*
@WarpedPerception 4 роки тому
Don't worry, this is coming in the next series, all of that stuff... Very soon.
@Comet-lv3nk 4 роки тому
A 50 psi turbo, with a nitrous bottle blowing into it...
@metaomicron72 4 роки тому
Thank you for this series and more stuff to come! We'll be here to watch it :) You're awesome
@kjell-richardlvdal373 4 роки тому
you are the best teacher i ever had, making dry theori into understandable testing in the real world
@fabio77809 4 роки тому
cabbage I cry my heart, that this episode is the last of the series of this turbo engine, thank you for your explanations that you gave us about this engine, I do not see now that the second season of the turbo engine is coming out immediately
@buder5116 4 роки тому
14:21 noticed the spark going through the hole while in the air ? Awesome
@SWXSTXK 3 роки тому
respect+ for this dude to stick onto this project for such a long time. absolutely loved this series. binged watched all 8 eps in the whole night. its 5am now. gn!
@NitroGuyJH 4 роки тому
Been a great run Matt. I’ve watched each episode from the first upload to now and can’t say that I’m not pleased! Great work, awesome videography, ad killer content brother!
@williamhart4896 4 роки тому
Those old Briggs and Stratton engines are tougher than I would've thought
@slitherixxx 4 роки тому
the dedication and effort put into this.... i salute you
@jamesadams2333 4 роки тому
Thank you for the wonderful series! Keep up the great work. I hope to see more!
@wdtripps6537 4 роки тому
Your skills are now to the point of spiritual insight. Awesome series
@Lozzie74 4 роки тому
You impressed me with your resourcefulness. The engine would stop, you would quickly figure out why, easily resolve the problem and have it running again soon after. You made electrodes from bolts! You are MacGuyver!
@LouieTheLug 4 роки тому
Thank you for all you do.!! I enjoy your videos. They are extremely educational and entertaining. I can’t wait for the next 2.0 or next see thru engine videos to come. ⚙️
@JesusGarcia-ec7jo 4 роки тому
The most nostalgic and satisfiying end that i'v see on a serie!
@Srikrishnakarthik 4 роки тому
Thanks man, appriciate all the effort you have put in. I will always remeber the first time I saw HOW IT ALL WORKED. I am an automobile engineer and makes me soo happy seeing this never really knew how it worked practically, it was always theory or prectical but this real time see through , blew my mind. God bless you, wish you and ur family good luck and fourtune.
@Les__Mack 4 роки тому
Fantastic series! Thanks for making these videos, they are awesome!
@just_j0e 4 роки тому
Kinda sad that you stoped doing this series it helped me at hard times thank you so much for theese videos 😊😊
@dhanisvaran5135 4 роки тому
Thanks for the all efforts , money spent & hard work... We love it 😍❣️ keep going on...
@Poshoo 4 роки тому
I can't wait to see what the next engine will be! Good video!
@NiCadHeliPilot 3 роки тому
Ka pai! An epic conclusion to an epic series.
@willemh3319 3 роки тому
real educative i showed your Br and strat to my daughters to show them how an engine works they loved it specially the destructive part of it👍👍👍👍👍
@backwoodsjunkie08 4 роки тому
Love your videos my dude! Keep up the awesome content
@MoisesQuirozT 3 роки тому
Great job megasquirting that small engine man, I can't get enough of your videos, thanks for the effort you put on them.
@g2westwood 4 роки тому
no way man , don't give up .... I love this series!
@daszieher 4 роки тому
Excellent series! You normally only get to see this kind of stuff in a lab. Very good piece of entertaining education!
@pw383426 4 роки тому
Yo man. Your ingenuity is the reason why I watched EVERY episode of this series. All the fights, struggles, and issues really kind of forced you (and us) how to learn about mechanical engineering. So cool. I hope the next project is just as ridiculous and as home made as this one is.... I'm hoping for a supercharger episode for christmas
@WarpedPerception 4 роки тому
Thank you, I also find that to be true and that's why I like doing these episodes this way, as we figure out solutions for unforeseen problems we learn a lot that we didn't expect to about things that we didn't expect
@max_power8510 4 роки тому
Your determination is admirable. I like how you kept trying and trying. It was very awesome to watch. Only thing I can think of is to use a nut on the bottom side so you could thread a regular spark plug through the top, but it would require more work. Like I said, excellent video and thanks for pushing all the way through.
@davyarthurs 4 роки тому
In the slow-mo you can see that the ECU runs a waste spark system. Been a nice series this one. Can see some serious work and effort has gone into it!
@radekciskowski2070 4 роки тому
The amount of work, time, knowledge and skills you've put into this thing and all this just to show it in this episode is incredible! The next episode should be to make it run on diesel - that would be quite challenging... but you wouldn't need that stupid spark! :D
@jacebigelow 4 роки тому
I enjoyed this series very much, your persistence and determination is great. Incredible camera & lighting work too !! Cheers !
@WarpedPerception 4 роки тому
Thank you.... And on to the next. That's one of the reasons I had to bring it to an end no matter what, gotta move to the next projects which are bigger and better.
@dubleblitz 3 роки тому
One of the coolest things I have ever seen in my life
@peabow1031 4 роки тому
Thanks I enjoyed the journey.
@RayJonesXD Рік тому
One of my favorite series on youtube I've watched :D Thanks fam
@floridapielady 3 роки тому
The entire season I was freaking out. Not over the anticipation of the engine exploding; that had me on the edge of my seat in excitement! I was freaking over that $140,000+ dollar Phantom Flex 4k high speed camera setup you were using. It was so close to the engine I thought any minute kaboom and the camera would be toast or covered in oil, etc. Seeing that would be the equivalent to witnessing a wreck of an exotic or rare antique car. I hope it's insured! 😉
@CoolayyyPlayz 2 роки тому
2:07 omg the engine sounds so good and so smooth. sounds like a four wheeler engine at this point.
@1071Halil1453 4 роки тому
Perfect test thanks bro
@bryanroupe8646 4 роки тому
This series has been awesome. Deserves a ton of views and likes. You have a wild imagination.
@daniel_poore Рік тому
Ive been waiting to watch your ignition screw shoot out the top for 8 episodes now! It finally happened!
@tylerstrausser7651 4 роки тому
Time to sell it on Craigslist. “Never abused. Rarely used it.” Lol
@wesleybuck5725 3 роки тому
Brilliant Series! A way to get around the turbo not wanting to boost more is to use nitrous to spool the turbo or just using nitrous without the turbo. Should be able to inject enough nitrous to cause the engine to blow without much effort. A come back with nitrous would make a brilliant episode...
@sepehrmovahedijalali3054 4 роки тому
Awesome Series. That was a mixture of theory and action I really love it.
@WarpedPerception 4 роки тому
Thank you !!
@lexus_offroad_adventures 4 роки тому
Been waiting for this video! So cool to see boost doing its thing.
@austinkreller7592 4 роки тому
I loved the series man keep it up! To help the ECU receive proper input make sure you have a ground probe spaced .035 away from the spark lead, gives it a place for the spark to jump to and a proper ground. Not having a ground to the coil will cause all sorts of issues within the ignition system
@FgMar-eh7xd 3 роки тому
You are a crazy man, I like to see the engine make the explosion, nice video
@SpaceShipDeathstar 4 роки тому
I never knew that a simple bolt was acceptable as spark plug. Amazing content!
@shipshrekt2156 3 роки тому
It’s not lol
@abelferquiza1627 4 роки тому
Your work should be seen and studied un every mechanics or engineering school, college and universities. Thanks for sharing with mortals!
@sirBumpyCase 2 роки тому
I really appreciate your slo-mos and overall production quality!
@WarpedPerception 2 роки тому
Thank you
@MrRolandeid 3 роки тому
Awesome job, stuck watching the whole episodes, i was excited to see how this engine evolved, i thought we might see it on a plane 😂
@marktucker208 3 роки тому
You are a clever guy, incredible
@user-hq4ly7xu5m 4 роки тому
That so beautiful burn !
@neoplasmax 4 роки тому
You were saying "something cool has to happen" in attempt to try and blow it but I have been thinking something cool already has happened.. It can survive a turbo and nitro! Now I'm heading to store to get a setup and put this on my go-cart!
@boltonky 4 роки тому
Great video and i do like how in depth you go without getting over the top....only problem i had with whole thing is the injector not being aimed downstream so fuel keep atomised
@nonstopsaurier 4 роки тому
Amazing Series!
@MrAjam12 4 роки тому
You should put that setup on a go-kart with the turbo and EFI.
@paulodaxx 4 роки тому
wow! Great video! Thanks!!!!!
@ColdSmokes 4 роки тому
The see-through head was certainly cool and all and quite a bit can be learned about the combustion process but it was ultimately the Achilles heel of the main objective to blow it up. The head was going to fail every time before any hard parts would or could.
@login866 4 роки тому
i got a suggestion, why not use compressed air from a compressor to charge the engine since the turbo is not making much boost. usually a engine internal can take way more then 5 psi
@drakethesnake1000 4 роки тому
This is sooo cool... Thanks Man
@zdrehsbuckland488 4 роки тому
I think your main issue is the length of spark gap which is allowing the voltage to spike much higher than intended which in turn creates large electromagnetic interference spikes - these will induce current spikes in any nearby wiring or sensors. The fix is to shorten the spark gap back to same as speced for standard spark plug, maybe add an extra grounded bolt at an angle which will make the spark gap adjustable
@ThinkCleverAndSmart 4 роки тому
Wow, this is good PR for Briggs & Stratton. Also, loved the montage at the end! :)
@kenbirkin7753 Рік тому
great series , and thumbs up to brigs straten, i have punished Honda GRX in normal operations but many makes would have broken
@koenjanssen81 4 роки тому
So now I can't wait for the second series to start. It's like a series on Netflix 🤣
@WarpedPerception 4 роки тому
Lol... Thanks, I never knew people would like these so much.
@koenjanssen81 4 роки тому
@@WarpedPerception it's awesome to see. As I don't have the funds and time and let's not forget knowledge to do this I really enjoy whatching these videos
@mastershefu147 4 роки тому
Netflix for men
@koenjanssen81 4 роки тому
@@mastershefu147 hahaha true story
@djaydeved 4 роки тому
@@WarpedPerception ay i got an semi old predator 212, though postage would be more expensive than you just buying one straight from the usal suspects. (harbor freight special)
@wesb9546 3 роки тому
This entire series is so brilliant. It reminds me of a drunken idea i'd have with a friend and then never follow upon...good job on not only doing this series, but doing it really well. Excellent execution, amazing production, ect. Well done sir!
@WarpedPerception 3 роки тому
Thank you, that's also how I feel at times, like it's some drunken idea!! Lol
@wesb9546 3 роки тому
@@WarpedPerception and you respond to comments! next level dude.....hey as a follow up, what's your background? just wondering where you got all these highly developed tinkering skills...
@PhantomHighSpeed 4 роки тому
Oh Matt, the music near the end. Good by see-through engine. You were a good friend!
@andremeyer1449 4 роки тому
Thanks...sometimes you have to stop when it's best 😍
@-DarkKnight- 4 роки тому
I like that you do a "Loudness Warning". I'm always using ear buds, so when it gets loud, talk about pop an ear drum lol.
@WarpedPerception 4 роки тому
Thank you, yeah I started doing that because previously I used to turn the volume way down, but then people complained that they couldn't hear the sound of the engine, but then if you're wearing earbuds it's a completely different story..lol like you said pop an eardrum!
@FRANK1092 4 роки тому
hello Man, thank's very much for the content, was amazing. gad bless you.
@abazzi910 4 роки тому
Nice videos, man! I love the content!
@natequillin4365 3 роки тому
New subscriber here. You are on to some seriously interesting stuff man, nice work
@natequillin4365 3 роки тому
Also, how to you avoid carbon monoxide poisoning?
@sampence1928 3 роки тому
The wood screw bouncing around the table near the flywheel reminds me of final destination. Lol
@a1sloth1 3 роки тому
EXCELLENT TEACHING TOOL!
@vancemacd6315 4 роки тому
I would put this in my car and probably race most the Hondas around my area. Great series,
@wildefox1478 4 роки тому
Pretty awesome, too bad it didn't blow up but that just shows how indestructible Briggs engines are! Looking forward to the new series!
@lesslisilverman 4 роки тому
Briggs and Stratton should be making car engines.
@keithy4129 4 роки тому
The engines on most modern day cars are incredibly reliable. It’s all of the electronics that are the problem, this Briggs engine is a tank because it’s is very simple.
@redneckasmr-xd1gg 4 роки тому
we can thank the epa they wont let car manufactures use the flat head design anymore because it is not efficient enough for them
@Eduardo_Espinoza 4 роки тому
flat head designed engines died out in the 40's or 50's for cars the reason lawn mowers still use them is because they don't need a lot of power and it's a lot cheaper
@CustomcrowdMitroc 4 роки тому
Toyota landcruiser is pretty much a b&s engine they are just as reliable
@djaydeved 4 роки тому
yeah they could make something beter than a 2jz or any famous engine that is known for being able to take a 1000 shot of nitros oxide (nos)
@AdriqueGames 3 роки тому
This guy deserve more subs!
@PlaanPee 4 роки тому
Issues with the crank sensor may be caused by the stock ignition flywheel magnet. When i installed a electronic ignition to my lawnmower engine, i put a sensor to outside of the flywheel and it was giving a messy signal, then i moved it to near centre of the flywheel and the signal was all nice and stable. All n all cool experiment and a good effort !
@upsidedowndog1256 4 роки тому
I might have gone for broke with the iron head, but you did a great job with this series. I look forward to more of your videos on all of your channels.
@WarpedPerception 4 роки тому
Thank you!
@ssj3mohan 3 роки тому
vert fun to watch.
@michaeldemetriou1399 Рік тому
That is a great creation
@EBAAutomotive 3 роки тому
You are wicked smart bro!
@jerrypizzini 2 роки тому
This was cool to see.
@user-md1nk6nu1m 4 роки тому
الراجل ده فنان بجد
@underratedsoul414 3 роки тому
Biggest thing "he never give up" 👍👍👍
@sinewave3323 4 роки тому
Awesome bro! Gd to see ya again! I wish you and you're family a happy new year! And a merry christmas! Ik its early lol! But just incase! 😎👍🏻👍🏻
@chaosminecraft3399 4 роки тому
Nice engine. It is not destructive with the clear head. Nice. 😉👌
@angelobovara317 4 роки тому
Stuff I dream about. Thanks
@marcio8417 4 роки тому
Parabéns pelos vídeos,
@borilopez8581 4 роки тому
Very cool thanks
@xxxftcxxx 4 роки тому
Send that drill to AvE and let him take it apart!!
@americanlivesmatter-BmanWild 3 роки тому
The slow motion cam and the music chosen is a really good touch ..well done bro!
@mohammedabenourseddiki6860 4 роки тому
Thanks for the sound warning it saved me from earrapes
@RistaMotorista 4 роки тому
too bad this series is over maybe use honda engine for next series? or a see thru rotary engine, wich is my personal favourite
@scenicdepictionsofchicagolife 4 роки тому
Haha he actually has a see thru rotary series already!!! Go check it out!
@WarpedPerception 4 роки тому
@@scenicdepictionsofchicagolife yes and I'm currently working on the second version of that rotary engine which was initially supposed to be the first episode but I ended up going with the simpler smaller design instead so everyone can understand.
@vincentrobinette1507 4 роки тому
It would be difficult, to build an overhead valve cylinder head out of plexiglass. Valve seats, and the exhaust valve guide just get too hot!
@scenicdepictionsofchicagolife 4 роки тому
@@WarpedPerception that's cool dude. Wish I could check your shop out 😂 I live in Chicago too by Portage Park
SmarterEveryDay
Переглядів 12 млн
Diego Saul Reyna Español
Переглядів 2 млн
GommeBlog.it: Tecnica e Performance
Переглядів 21 млн
Влад Закроев
Переглядів 8 млн