What Can Be Made From An Old HDD | Amazing Idea Using Old Hard Drive

2 роки тому

Hi friends,
In this video I will explain how to convert computer hard disk drive into a sander & how to run hard disk motor without a driver circuit.
You will learn how to use old hard disks, and what can be made from these old hard drives.
Second, you will also learn how to run its motor without a driver.
#harddisk #hdd #oldhdd #hddreuse #electronic #tariqlab #fewpeopleknowthistrick #bestideas
#top3electronicprojects

КОМЕНТАРІ: 32

@riyazriyaz2871 2 роки тому

Amazing idea to use old hard drive, thanks Tariq lab

@hadicutiepie3583 2 роки тому

Grea brother Tariq, thanks a lot

@abdofekry9957 2 роки тому

Well done Tariq, thank you so much

@mrigankasinha1454 2 місяці тому

Very neat and clean work, Thanks a lot, wish you all best for next project through your valuable hands❤❤❤❤

@TARIQLAB Місяць тому

Thank you too

@ErCanEverything 2 роки тому

👏👏👏🤝

@hankhomaomes2830 3 місяці тому

Brother i have done everything as you've shown in the video however mine is stopping after 9 secs and not starting again unless i plug out and in again , i read one person mentioned that some pins needs to be connected in order to avoid "the stopping" like what people do in SATA HDD pin 3/5 or 2/6, which pins needs to be connected in PATA HDD?

@usmankadir4834 2 місяці тому

how to make harddisk running continously , not stopping after 9 secs ?

@shhamad Рік тому

I have seen many videos, this one is the best using the LM7805 to by pass the 30 sec on/off spinning restriction of the smart hd.*update: The mosfit got really hot after 1 min run, i placed heatsink under but i think it wont last long.

@danhayes5225 11 місяців тому

i don't think the 7805 is necessarily a mosfet but is just an old standard 5 volt regulator and that is it. Where are u getting this 30sec on/off spinning restriction.

@amitagrawal9672 Рік тому

Hi. I am using almost same pata hdd and giving it supply from a 12+5 volt adaptor instead of 7805 ic but hdd motor stops quickly like 15/20 secs. Any other hack you did in the hdd circuit board?

@TARIQLAB Рік тому

May be voltage drop, check both 5 & 12 v

@amitagrawal9672 Рік тому

@@TARIQLAB nope. It wasn't voltage drop. You missed the part where Data pins are required to be connected in order to run hdd constantly. I did that and now it's working perfectly.

@shhamad Рік тому

explain what did u do? thanks

@adnanakhtar7 Рік тому

@@amitagrawal9672please can you explain which pins need to be connected I am also using pata

@shonmeller4289 4 місяці тому

@@amitagrawal9672How bro😊? Tell me, how???😢

@keenowl1410 Місяць тому

Awesome

@TARIQLAB Місяць тому

❤️

@user-fd4lc2tl5t Рік тому

شكرآ لك ولكن نريد نسمع شرح مش موسيقا

@Mr.Legend_9 Рік тому

After this I'll go to data recovery center to retrieve my photo

@AlCatrraz 11 місяців тому

The problem.... It is not good for LARGE KNIVES... maybe cutting the sides of the slid frame ..

@TARIQLAB 11 місяців тому

You're right

@dannydiehard6596 Рік тому

Whats with yall playing music over the video like if we came on ur video to dance bro , STOP USINF MUSIC ON INSTRUCTIONALS ITS ANNOYING AF

@TARIQLAB Рік тому

Noted Boss

@danhayes5225 11 місяців тому

can anyone figure out what he did with that 7805 regulator and why waste all that power rather than just apply 5v into the 5v terminal only and forget about the 12volts. It's not that sensitive to exactly 5v.

@TARIQLAB 11 місяців тому

To run desktop hdd 5 & 12v required

@allexperimentking808 Рік тому

Not working

@TARIQLAB Рік тому

Why?

@user-ye5xu8yt4g 6 місяців тому

@@TARIQLAB @amitagrawal9672 1 год назад @TARIQLAB nope. It wasn't voltage drop. You missed the part where Data pins are required to be connected in order to run hdd constantly. I did that and now it's working perfectly.

@hankhomaomes2830 3 місяці тому

@@user-ye5xu8yt4g which pins need to be connected in pata hdd ?