I have seen many videos on xbee configuration but this is the best one . Thanks a lot

Thank you sir, you made my day I was stuck with xbees communications problem but now it's done.

Thank you so much for such a informative and simple explanation.

Thank you sir for this wonderful Tutorial.

Video is very well explained. Hope to see more tutorials on IoT from you

THANK YOU!!!!! It is finaly working after few days

thank you very much sir ....... I requested you for S2c module ....u did it ......thank you very much 👍

TRULLY AN AWESOME VIDEO THANK YOU SO MUCH!!

This video is very much useful. Thanks a bunch sir!! :)

Great work ....nice explanation

Great Sir, Thank you so much

Thx very much. It's right and clear !

THANK YOU SO MUCH!!

Thankyou sir.... very useful

Thank you Mr. Saravanan for this tutorial. It was very helpful to learn how to use the Arduino to connect to my computer serially. However, I wanted to add a couple of issues I ran into for others who may also encounter these problems. Now I'm not sure which of these issues actually fixed my problem, but I will list them here... 1. My S2C is a programmable zigbee radio, so I had to use the "Add radio specifying port settings" option in the top left . If you have a 'B' at the end of your xbee model number, then your xbee is programmable as well. 2. I had to reset the radio during configuration. If you are using Arduino as in this video, you can place a jumper from ground (pin 10) to reset (pin 5). If you have a breakout board and can place the Xbee on a breadboard, then a push button switch is easiest. You only need to set reset to low for a second. (Note that it took me about 3 tries with the right settings before it took). 3. My xbee radios had a default baud rate of 115200. I received them from Digikey. If you are doing the above 2 steps with no success, then try playing with the baud rate. From my readings, 9600 and 115200 are the most common. When using the "Add radio" option with a programmable radio, you will have to try each setting one at a time. Give it a few tries on each setting (see end of note 2). One last thing I'll add is that I also installed the usb driver from digi.com. I think this is supposed to be for the usb item they sell, but it can't hurt to install it anyway.

Thank you very much SIR for nice tutorials....... I would like to request you to make one tutorials in which please tell us to configure one to many mode ???????

Well done. Thank you.

Devamı gelsin reis

How to form a mesh with 2 routers and 1 coordinator for S2C modules?

Is it possible to use an in-built microcontroller of the zigbee to run some scripts ? If you don't want to trigger it from external microcontrollers.

Can you provide any documentation on how to configure zigpy into Xbee? Also can tarang P20 be used as the same?

Thanks a lot!

best ever

hello sir. ty for the tutorial. can you answer my question? I want to form network with 3 device xbee. 1 for coordinator, 1 for router, and 1 for end device. what firmware should I use? thank you.

Thanks for the lesson, I have a problem. My xbee is mounted on a My API cannot detect the xbee any help

Very nice

????Thanks for video.. If I want to communicate point to multi points how I configure the two Xbee

Nice for the arduino trick!

Thank you for video.......Can you help me to create mesh network where all zigbee is with stm32 controller.

Hi Sir. Is it possible to connect an antenna that we have made to the zigbee xbee?

Hi! I am using the Arduino Micro to configure my XBEE board. The micro has two reset buttons on it. How do I bypass the bootloader? I tried uploading a blank code but I am unable to detect the device.

Hello sir, If you have done maximum distance test then please tell, What is the practical maximum distance in which xbee can communicate ??

Thanks =)

very nice vedio

Sir i have configured xbees accordingly as shown in the video above but am getting garbage values along with the received data. what is the solution?

Hello Sir, May I know how to configure mesh network for Zigbee Xbee s2C

I have a question, can you connect directly pin rx-> tx between xbee and arduino ? I have seen this worked corectly but how ?? xbee is operate by 3.3 v .

Sir please make a video on sending flex sensor data from Arduino to Xbee to control servo motor on receiver side

hi sir, What is the outdoor distance of xbee s2c? please quick reply

Hello Sir i use the xbee explorer dongle to connect the xbee to the computer...but the xctu does not discover the xbee radios... can you please help on this

How to transmit and receive using user defined data i.e Rx with fixed size data and Tx with same data @ 100ms /1000ms etc from one system to another

Sir, can you please make a tutorial about sending data from flame sensor?

ardunio not connecting without xbee explorer. I disconnected it, introduced it, then connected it to arduno, but it still couldn't find xbee, what should I do? can you help me? We will also communicate with BME280, Adafruit GPS, MPU6050, RTC DS1302 via xbee s2c. We wrote the codes of the sensors, but we could not find and understand the codes we need to add in order to send them via Xbees. Your code is too short. will it work? Are the xbee codes different for each sensor?

I dont undestand why you connect TX to TX and Rx to Rx? It should be reverse right?

Hi everyone :) Can you please help me understand what is the difference between Transparent Mode [0] and API enabled [1] under Serial Interfacing, AP configuration? (04:37-04:46 in this video) Thank you

heelol how can ı connect xbee to mission planner . there is error(heart beats not received )

Dear sir, please let me get help from you to make video how to show RSSI of Xbee S2C using arduino program

my xbee ps2c(pro) not show in xctu

I can't get the router to work? Tried another xbee and router still don't work? Hmmmmmmmm

Sir G plz Hindi may bhi video banya karo

hello mr.saravanan i've seen your post in wordpress that your account is suspended without any reason how did you get back your channel.my channel also suspended without any reason i just uploads about camera sample photos and audio also free copyrighted..please help me to get back my account :(

Mercee

Parti kur oy vereyim kral

buzzzz

hello mr.saravanan i've seen your post in wordpress that your account is suspended without any reason how did you get back your channel.my channel also suspended without any reason i just uploads about camera sample photos and audio also free copyrighted..please help me to get back my account :(