Very few people anymore with your talent and skill set. Loved your video and the time speed presentation. Your parents should be very proud of your ability. Thank you from Nor Cal.
@AnierPalacioPadronДень тому
Magnifico el aserradero de cinta
@AnierPalacioPadronДень тому
Me gustaría construir uno
@AnierPalacioPadronДень тому
Me gustaría construir uno
@AnierPalacioPadronДень тому
Buenas si me pudiera enviar las medidas del aserradero de cinta
@hasankutlusoy4597День тому
Lazerde kesilen parçaların çizimini detaylı olarak anlatabilirmisiniz
@joshuamittie791День тому
Put your tires on the right direction
@silentepsilon888День тому
I think you could save yourself some time and many steps walking back and forth by making several vertical cuts first and then run one horizontal cut to cut off 3 or 4 studs at the same time.
@maxpro9346День тому
An automatic winding system for the electrical cable following the saw should be a good improvement. It’s dangerous on the ground, for it and for you. With a spiral spring and a supporting cable in addition so that it can be supported lengthwise.
@xargi12 дні тому
Для уменьшения сопротивления при перетаскивании бревна лебедкой, продень трос через конус.
@patrickbilderback15462 дні тому
Good job on the remodel
@Kingoftheroad20002 дні тому
Czy ta piła jest globus pl ? Pieknie brzmi
@rwelpers2 дні тому
Pretty is not always necessary, but it is appreciated. You do good work
@agustingonzalez69122 дні тому
What is the thickness of the tube and the metal plate?
@rudyrivera74262 дні тому
👌👍
@faristafogang79642 дні тому
Hello How much this machine ? Im from Africa
@miguelpagansr61282 дні тому
Looking good so far, that's the modern version of the manco big cat minibike. They weighed 215 pounds.
@nobuddy46113 дні тому
Nice work and product of time well spent in you apprenticeship. But oh my, please clean that chuck and ways on the South Bend.
@beefer05103 дні тому
What is the offset measurement you used to create your shaft? I’m shopping for bearing and trying to figure out what the throw of my plate should be.
@barthanes13 дні тому
What kind of wood is that? It looks like ash or elm. I had almost forgotten about the mini bike. I can't wait to see it run around the field.
@ih8s8n3 дні тому
Man I bet it would be nice to have that electrical cord up above you on a retractable line or curtain rod so you didn’t have to constantly move it or trip on it. What a well planned and executed saw mill! I’m always amazed at how well you design your builds. When you added the crown to the beam was there a formula you used to try to get it straight after the sag that gravity causes? Or just a guess? I’m really curious about that. Thank-you for all the great content! Cheers from Canada 🇨🇦
@rmautomacao40653 дні тому
Você poderia enviar esse teu projeto para mim
@martinb53983 дні тому
Needs a laser level on the blade plane so you don't have to eyeball it ;)
@DonnDIY3 дні тому
I already ordered a cross laser that I'm going to install on the mill.👍
@EmadAli-ve8rh3 дні тому
عمل.ممتاز.و.دقيق.و.مراحل.التصنيع.متقنة.،،،اذا عمل،احدكم عملا أن يتقنه❤
@robertnaughton54173 дні тому
I’m totally impressed with your skills
@paavokaleva4 дні тому
Saarepuust pink, see on vast igavene.
@DonnDIY3 дні тому
Oma paarkümmend aastat ikka kestab vast. Nagu vanaisa tehtud pingidki. Aluspakud tuleb ainult varsti ära vahetada.
@tyceilican4 дні тому
if you wanted to revive the color of the plastic you can hit it with a fire torch lightly and it will bring all the color of the faded plastic back, then you can spray it with uv protectant.
@Towards324 дні тому
After filling up the tank, fill it up with a couple of bars, higher pressure will be better, right?
@nidalshehahadeh74854 дні тому
One way of dislodging a rusty brake piston is by using Grease, install a Straight Zerk Fitting Grease Nipple Fittings in place of the bleeder or at the hose and pump it with grease
@opuak4 дні тому
kas see tera ongi muidu mõeldud mõlemas suunas lõikamiseks?
@DonnDIY4 дні тому
Tera lõikab ikka ainult ühtepidi - horisontaalis lõikab ketta "parem serv", vertikaalis ketta "vasak serv".
@4littlechicken4 дні тому
Mineral Oil on the blade. Be surprised how good it works :)
@sdspivey4 дні тому
You are measuring the pulleys wrong, it is the inside diameter that matters. You are getting wrong ratios.
@ThomasSedig4 дні тому
skulle varit sväng bara stöttor
@job38four104 дні тому
Nice mill, even has electric start..... How come you didn't use your pressure washer to clean logs........
@dstevenpaisley4 дні тому
Sweet saw!Have quite a few buddies who have saw mills but they are all bandsaw mills .funny how you guys use electric motors .here wood be run by gas or diesel Your one talented man.Great videos thanks Steven
@lucasconstantino38845 днів тому
Hello donn DIY, which country are you from? I follow you here from Brazil.
@DonnDIY4 дні тому
Hello from Estonia.👍
@pelleryck5 днів тому
Add one of those rotors that runs infront of the blade That cleans the wood
@brunoorlandi17735 днів тому
Complimenti, le atrezzature che costruisci sono davvero fantastiche, anche il tuo veicolo offroad è molto interessante
@user-bf6tn2zn6w5 днів тому
Sõber - sa oled geenius! Teie looming on geniaalne! Aga sa kasutad metsa kingitusi ja puud kasvavad aeglaselt. Siit saate teada, kuidas metsa taastada. Istutage uued puude seemikud. Друг - ты гений! Ваши творения гениальны! Но вы пользуетесь дарами леса, а деревья растут медленно. Узнайте, как восстановить лес. Посадите новые саженцы деревьев.
@elijuseee5 днів тому
Like someone said, nice to see that your projects are in use. 👍
@roman13245 днів тому
Система когтей нужна теперь, чтобы бревно держать за низ крепко.
@Adub865 днів тому
Yo Donn! Nice saw. What do you do as a profession? I’ve always been curious. That saw is so damn cool.
@martinp88895 днів тому
Very clever 😀. Have you thought of putting your power on a pole mounted on the carriage at say 60-70 degrees so it’s over the top of you and to the side to avoid fouling on saw or a trip hazard.
@jamesadams8935 днів тому
I really like this channel, one of the few creators of this type of content that doesn't talk us to death while he's doing the job
@guygillmore29705 днів тому
Yes , see also New Yorkshire Workshop
@SManninen5 днів тому
Just a suggestion: put the power cord on the other side of the machine and put a 1-1.5m lenght tube to the side of the sled (to the right from the operator point of view) and tie power cable to it. That way it can move freely on the ground with the sled and it is not in your feet all the time.
@serzhdyubro80835 днів тому
Seems, you need to make some kind of the frame to put logs on and fasten for better cutting
@president25 днів тому
Love it so much keep it up as always 💘
@olddawgdreaming57155 днів тому
Looks like you did great on this one too. Didn't think I'd like it but you won me over on it's usefulness. Keep up the great fabrications you come up with Donn. Your work is very entertaining and always learning something new . Stay safe and you all keep up the fun around there. Fred.
@DonnDIY5 днів тому
This sawmill is a specialist tool. Not that I'm a swingblade specialist, but this sawmill has its dimensional lumber cutting niche to fill and it does it perfectly. Slabbing would require another cutting head. For dimensional lumber I personally wouldn't use anything else. This sawmill has really grown on me. But that's just my personal opinion.🤷♂️😀 Cheers, Fred🙏