Hi nice vid but I noticed that the highest reading is PEFC 950.3 this one should be doubled and recorded not the PSCC am I right? THANKS

How did you know where on former the 2nd mark had to go to bend?

You should voice an animated movie character. (I am not joking)

Art

Nice tip about scoring the conduit for the thread line.

very nice

Thanks mate, got my am2s this Monday and this is spot on 👍🏻

christ ! - kill the music and the avatar... then you've got a great video !

Fantastic video. Thank you 👌😀

Excellent video as always, thank you.

Very good work

helpful but surely that Zdb your say is Ze because the is the 3 phase dno supply? is zdb would be at 2nd or 3nd distribution circuit ? ASKING

Hi I am having a few issues on identifying the types of wiring and reference method on the Generic schedule of circuit details. Can help or advise please?

Brilliant video, really appreciate the time taken to animate the test sequences as well. Helps to visualise what you’re doing so much better!

Enjoyed the video. Would like to see more testing videos if possible.

excellent 👍

Cual es el modelo y la marca de la dobladora

Very detailed video. 👌 Much appreciated.

Great video but how do you know when doing the 1st and 2nd bends on set where bend starts on former please!?

This brings bk memories of browsing.

thanks!! very useful video!

Excellent detail & instruction, thank you. 🙏🏻

Very informative, thank you. Subscribed.

Super

Loved this vid, super simple and easy to understand compared to others, hope you release more content

Great video

Fabulous presentation, excellent visuals too !.... If i might just contribute ? In my view, the purpose of the solar hot water system is to reduce the need for energy consumption ! The reason I mention this is because the solar needs to operate independently from the boiler . The D.H.W timer should be programmed to schedule a periodic " top up" of the storage tank to overcome any shortcomings of the solar performance during dull weather, and reduce legionella by bringing the water temperature up to a suitable level. My system for instance, runs twice daily to address water & / or heating, based on the Honeywell programmer settings. I also use an S-Plan too, using my combi boiler to provide heat, triggered by the room / cylinder stats leading eventually to the output of the microswitch in the zone valve(s). My kitchen hot tap still runs from the combi directly though ! It has worked a treat for about 6 years and i find the boiler hardly needs to run between May and end of September due output of the 8 square meters of thermal solar panels on our roof. The boiler is still timed to come on but the cylinder stat is usually open by that time so no heat is required. Winter time is another story ... but the boiler still only needs to heat lukewarm water already warmed in the bottom of the cylinder. I often wish i had a second tank in summertime as it often shuts the pump off and stagnates until somebody takes a midday shower. A "destrat" pump and a few controls help to maximise efficiency. Brill animation ... Thanks for sharing.

Excellent tutorial.

Very clear and easy to follow demonstration

Great video well informed

where you had the running coupler and lock ring can you not just measure say half of the coupler so that when you tighten up the running coupler with the end you wont have any tread showing ?

great video. keep posting

Wasting 4 inch of pipe I would get battered by my tradesman back in the day 😂

Good lesson

I’ve hit subscribe but only 4 vids available. Can you do a vid on the DOL pls ?

Where can I find that bending station

very good

great video. really useful

Came for the conduit, stayed for the music 🔥

What is the name of this bender? Where can I buy it from?

Exelente video amigo soy electrisista desde costa rica.... Yo para aser cambios de direccion o offset.. Tengo mi forma y se trata de tomar medida usar calculo con el teorema de pitagoras y centro marca dobladora y sale super biem amigo

Very helpful demo, thanks

Good demo.

Like it. Just to point out, this is a '2plate' method or 'through the switch'. Ideal for downlights where only 2 conductors are prefered at the light fitting.

I just recently passed my am2s assessment and want to say thanks. Your videos were very helpful in my preparation.

Just a quick question if the depth was say higher or lower than 53mm would you shorten or add more on too the 100mm in between the sets ?

Great masterji tussi great ho

The best demonstration on youtube.

Appreciate your generosity

Great job