Absolutely amazing job. I built it and it flys great this is perfect for beginners flys nice and slow but can still have fun with it. Thank you
@zeDoSauRus6 годин тому
60m/s? I doubt that :)
@zeDoSauRus6 годин тому
yes but why?
@wsm314День тому
Novice review to anyone curious. Indoor flight for an outdoor drone. No calibration before flight. Damaged before outdoor flight. Not a great review to determine what to buy for anyone curious.
@BoardyetiДень тому
Ok that's really cool. We need a night video of it.
@jonahtaylor9338День тому
This is amazing thanks
@psyberpirateДень тому
He really thought he did something with this one...and he ABSOLUTELY DID!
@harrychattaway1556День тому
🤣🤣🤣🤣 looks goofy as hell
@harleywainscott6059День тому
Neat!
@buildingwithloganДень тому
Wouldn’t it be more like “If a drone and a plane had a baby”
@simplydarkhalf3974День тому
Buffering
@murgyj61982 дні тому
A propelled propeller propelling propellers
@rollin18wheels16 годин тому
It’s like….. propception
@3579jh22 дні тому
Tie fighter?? Must be a trekkie ❤
@tomlatimer50012 дні тому
Adam, to say I could use your help is a huge understatement. I bought a heavy duty, all steel hydraulic loader from an online auction. It came with no paperwork, no instructions, and I'm totally new to this. Upon playing around trying to figure it out, I could only get the bucket to raise and lower. thinking there must be a problem with channels synced between receiver and controller, I chose the factory reset option, big mistake I know now. Ive been doing a ton of reading, and watching videos, about all of yours, so I think I have a grasp of what needs to be done. Doing it not so much. everything i have watched regarding binding the two, the receiver is out of the truck, plane, etc. Can I bind the two with the receiver in the loader? taking it out looks problematic. I have made a jumper bind wire, put it on with heat shrink protection from touching the center terminal. Can I now bind with the FlySky FS-I6S? If so, how? The receiver is a FS-IA10B. 2nd question, would you be willing to help me set the remote controller up? I am reaching out to you here, I am new to this so not sure where would be best. I need help bad! And it would be greatly appreciated! Tom
@superme632 дні тому
You mean the Tydirium shuttle.
@Johnnyhernandez19932 дні тому
Now a Tie fighter styled drone would look sick
@khwanchaiaopanya793 дні тому
Good ❤❤❤
@rceliberti3 дні тому
How is there enough channels?
@azhazellangedechus65593 дні тому
Trop grand et sûrement interdit en Europe déjà que les dji sont bridé à la moitié des États-Unis sûrement vu que la France est plus petit comme pays et qu'il est interdit de faire voler un drone hors de vue mais officiellement, officieusement il faut juste télécharger l'application dji mavic pour avoir accès aux capacités des drones dji
@arostaky3 дні тому
You have to pay to get further lessons, it's not free at all and the graphics and simulation physics are super lame
@samolet-legko3 дні тому
Шлак.
@scoreboardntlie3 дні тому
When your a trekkie and try to reference star wars to a stuning failure
@boopathipn17333 дні тому
Thank you so much..
@jamesordwayultralightpilot3 дні тому
You need roll and fish control...
@SulbhaHinglaspurkar4 дні тому
❤❤❤❤I don't have the money for this drone but I am trying to build a cheap one ❤❤
@jayrmarcelo4 дні тому
You are good at inventor 😘😘😘
@sgtkickazzTVShorts4 дні тому
Ya we need to make a TyeFighter
@glenmemeington70044 дні тому
Make this into a real machine to spray crops and do it cheaper than the current drone model’s and you revolutionise the world. Imagine a fleet of these solving world hunger, 1 shipping container full per village for $100k, all they have to do is get taught how to fix em and put seeds and water in em.
@thewayitis30544 дні тому
To much drag to slow
@thewayitis30544 дні тому
4 is better 👍
@logan84084 дні тому
Builder shuttle
@George255 днів тому
I have kind off the same issue , when armed without props looks like they are at full throttle.
@davehughes535 днів тому
Hmmm, are all you pickleheaded alien believers satisfied
@sumaiyasiddiqui88095 днів тому
now thats some chad stuff
@hornpoutclout5 днів тому
I messaged joshbardwell a couple years ago saying he should do this he scoughed at the idea you are my new hero.
@fpvdominator95634 дні тому
didnt mr steele do this with an old phantom years ago
@PH1LZ5 днів тому
Now that was incredibly helpful for setting up my dual motor boat. Thanks, champ!
@roybond99655 днів тому
Very cool!!!!! I want to build one
@nandishnaruni18945 днів тому
Bro please giveaway transmitter flysky
@cherrychicken6 днів тому
Heck yeah. Over here hot roddin mavics.
@aajpeter6 днів тому
$18 each for the prop locks???? Cray cray
@justOVERCH6 днів тому
Я думал это будет видео про прошивку ☹️
@boogabooganoob6 днів тому
Very cool
@user-xs1yu8fy5c6 днів тому
The drone in the background making all that noise doing 90 mph
@rockman49er3 дні тому
0 to 90 in like 1 sec though lol I got one clocked at 102 mph 😮
@RadiantCandyEye6 днів тому
Best drone design ever
@srikanth-zc7fx6 днів тому
Can we us fs-i6 with real flight evolution
@KaPohaku6 днів тому
Now make one the size of a commercial airliner, with the cabin attached via gyro
@stevoclark15337 днів тому
Can you buy this thing? What's it called?
@RCwithAdam16 днів тому
No. It's made by Nick Rehm. Checkout his youtube channel for the details.
@theanimecrown99307 днів тому
💝💝💝
@WaIterwhite3087 днів тому
Please how do you do that?
@wearemany737 днів тому
This design is very elegant, very smart and allows for some very economical flight. Nick really does have something special here.