Work wichtig this on nspanel pro the mic and stecker, too ?

thank you very much , how are the pre flashed tamsota device's holding up , any issues ? should I go for pre flashed or flash shelly?

Moes version is great, Works with zigbee2mqtt

im having an issue when trying to run the final command to install the xposed app, it is saying "no space left on device" I cant seem to find a solution for fixing this either any help is greatly appretiated!

where can you get free siren mp3's?

do you really need to flash it for it works out of the box with raspberry?

Mine has completely lost connection to the remote and the other dongle thing only way i can control it is by using the buttons on device any idea how to reset this thing

So if I just wanted to test this out with a couple of Aqara devices. I'd order the devices along with the M2 hub, yeah? If my internet went down that means I couldn't use my aqara smart lights?

Everythings ok till 4:47...Then I can not see on HA "success!" message...Tried one million times! :(

My boys just just got this for my birthday. Hope to start printing tomorrow. Thanks for the info!!! New sub!!!

Control F5 does nothing for me. It literally just turns the brightness on the screen down because that’s what F5 does.

This video is (currently) 3 years old. Have there been any changes since then?

the best way I found to get your eufy cameras into home assistant get a 2bay Synology NAS input your cameras through the Nas then use the Synology integration in home assistant seems to work quite well

Anyone else seeing the 'Wait for device activation' taking forever, it never moves past. Latest HA on latest pi.

hello all my integration gets stuck at this skreen 4:00 after i activate the code on github and return it just keeps spinning and spinning any idea why this mite be?

I've purchased 2 of the Sonoff Zigbee dongles over the passed two months anf I can't get either of them to go into Bootloader mode. I've tried two different ways and still wont work. May have wasted my money.

I haven't been able at all to get my screen to time out/ turn off at all the screen just dims. I have tried setting the time to 30 seconds instead of 15seconds and still no luck. Any one got any ideas?

Thanks for the Tutorial but just gonna let you know my Local Key included characters you might be using to assume the key has stopped, and so myprinted version had part of my key cut off, took me a while to figure that might have been happening and i just copied what was included between the " ", just in case it helps, my key included characters like : ; / ( + ? although it cut off at the : as in it didnt include that or anything after it.

One thing not mentioned is how you can use it with a metal bead chain that has a connector in the middle to join the two ends. The blind has a sealed cog wheel which the connector cannot pass through. The smart blind device has a cog that the connector also cannot pass through. The length of the chain between both cogs is not enough to fully open and close the blinds and it's already at the lowest part of the window recess. How do you solve that?

Can it be used in Wifi? Or do you need the Ethernet cable?

Thank you! Very useful video having just purchased the same but newer model. x

I got this installation wasn’t difficult but when I hook up my LEDs they just flash

Hola. ¿ Que transformador has usado? Porque solo viene el cable de carga y se indica 7,4V...No localizo ninguno😢

Is it possible to explain more in detail how to add this BBLED as a device in ESPHome in Home Assistant? I don't see it auto-detected.

Avoid this product. I bought it last month, took 3 weeks to arrive. After 5 minutes it stopped working and Moonside refuses to give me a refund. The worst experience possible. Dm if you need email confirmation.

Extremely helpful! Thanks for a great well thought of video

I tried the RTSP from your reolink but found that my eufy app assumed I had a NAS which I don't - do I need one to make this work? Would be helpful to do an updated full tutorial on these method. Thanks

Hello, great video as always! I finally received my BL led controller and I'm not really satisfied with the result with the current firmware, so I wanted to install Wled there but I'm blocking it...what is the configuration of Wled to use to run rgbcct leds? Which gpio pin to indicate? I don't currently have any reaction from the led strip 😒

Will this work with aqara products?

this does not work. says - "sorry I am having trouble ... with the simon says skill"

Great help, thanks, Mark! I just wonder which editor you are using at 19:00min to graphically change the size of the field. I would like to do the same but have no idea which editor to use (maybe you know one for Mac OS)? Any additional recommendation where to find further information how such changes can be done?

hi does this work with gateway sub devices ?

Did you ever create the Python method video? I cannne find it/one??

So, if I'm not home and the motion sensor goes on and/or the siren goes on, then I will get a notification on my phone I presume. But how would I know if there's a burglar or a deer walking by. Yolink has no outdoor camera that I could view the scene. Any way to do this? Is there a camera that can link with the hub or would I have to get a separate non Yolink camera? Anyone have ideas?

Everything okay with you? We don't hear from you anymore. Should we be worried?

Hello, thank you very much for the good review. Unfortunately, one very interesting point is not addressed: The projector has Bluetooth capability, and you can also use it as a Bluetooth speaker. However, is there a way to output the audio when playing videos via Bluetooth to an external Bluetooth speaker? Thank you in advance, I would appreciate an honest answer.

Hi! any idea to use in more than 1 speaker at the same time? Im not able to use in more than one.. looks like when 1 speaker is waiting for the response.. There other are not connected. Thanks!

Hi! any idea to use in more than 1 speaker at the same time? Im not able to use in more than one.. looks like when 1 speaker is waiting for the response.. There other are not connected. Thanks!

@MarkWattTech: Is there a native support for Matter devices, so I can use it without HomeAssistant? If not: Is it planned?

v3.0.0 cannot be rooted

is it possible to stream the doorbell via rtsp`?

Great tutorial. Thanks! I am def doing something to replace Alexa! Can’t wait!

Is there an Alexa version?

So, don't you need to put the line of code in your configuration.yaml file 'secret: ! include secrets.yaml'? (I did not see that line in your configuration.yaml file)

if you recomend ..... why why we can se how the alerts goes to you phone?????????????????????????????? Reply

I set it up but it doesn’t show on my tablet dashboard

Great video. Reolink is now native to Home assistant. Doesn’t need Hacks to work.

hi I have this problem. How do I switch all my devices from the Tuya app to Smart Life, without having to pair them with Smart Tuya again? Thanks, even if I don't give in I'll never get an answer

One thing that always fails this notification on HA. And that is your home network switch to backup internet since the primary one have some sort of outage. For some reason HA struggles to use the backup internet for some period of time (eg 30mins) and if for some reason that period of time you have no internet and there are some notifications needs to be send, well suck to you those notification will never get resend. Because HA is too dumb to handle that, I basically just add a automation based on sensors from my pfsense router primary wan status, if the sensor for WAN interface goes to down state for 1minute, it basically restart HA Core so it can use the backup internet.

I assembled everything and left the microSD inserted. Is this possible? have the SSD and also the micro SD? 2 of my micro SD cards were destroyed.