Hi, can I use the same device as Master to receive a command (e.g. swtch on a motor) from a different device like a remote controller and then translate that command in an analog signal (e.g. open the circuit to power the motor)? Thanks.

How to do for date and time

I am not able to find MD_Parola.h

Did you make the cable for RS232 to the display yourself? Or where can I buy?

Thank you so much sir, out of all the HC-05 pairing forums and videos on the internet, you are the only one who solved my problem!!!

Only works with older Raspberry Pi OS with Python2, so seems like buster, I have a pi400 which is bookworm and cannot run earlier versions of raspbian OS

Total cost

Thanks. Looks very nice

I think your wiring in the video will destroy your micro controller, as you swapped VDD+(14) and VSS-(5). Your green wire is connected to pin 14 to GND on Arduino. So, it would not work like this. Most probably you later re-wired before you programmed the PIC.😀

thank you so much, after a month lcd is worked looked for many lcd videos but nothing worked

Thnx bro

Is the same can be done with esp32 camera with a IP address generate by it to store a data????

lcd display is coming blank nothing is printing. what to do sir

Anyone tried pic16f877a?

Which restauranter are used

Helpful video. Kindly, make a video on controlling output, reading input from pins

well done, steps in detail + your illustration spoke with confidence, well done !!! bravo bravo bravo !!!

thanks for the video!

any reference for interfacing p10 red led display module with rpi pico??

Can it be accurate as .1mm?

I didn't know this was a possibility, still can't update the firmware but I can upload code, thank you!

Works GREAT ... Thank You ... Please, how can I slow down the "scrolling speed " or make it smaller and stay "still" ? .... Best Regards ...

do you have for raspberry pi 4?

PIC16F877A can programme ??

@ 1:32 - There is no 'Trust Workspace & Install' so i have no ides where your platformio extension came from bit is not the one that appears top of list if 'platformio' is typed in the top editbox. Just a heads up to anyone in same state of confusion as I am, as you must be doing something no one else can replicate. Kind Rgds. EDIT. Just a thought, are you sure you don't need the extension 'Arduino' from MS, that sounds more like it ??. Again just a hint for anyone else trying to decypher all this.

CMD consol commands are impossibly small to read.

subscribed thanks

very good tutorial, thanks! TIP for future viewers - if not seeing text but the screen's backlight is on : make sure you use correct voltage (I mistakenly used 3.3V but mine needed 5V) and adjust the contrast screw on the back (in the blue part) while the python script is running

Will that only work over the WiFi or can this be used when on holiday 1000 miles away?

you does not explain what is the root certification and how to have it

Can we do it without adapter?

Can you make the same please by using dht 11?

where the hell is the code this video confusing af

Raspberry Pi ruined the development experience with its reliance on CMake.

Hi! I hope I'm not too late, can i ask where can i buy the RPI holder that you used? Or is it customized?

Good evening sir can we program any series of PIC microcontroller using your method plz reply

HOW TO CHANGE FONT SIZE? YOUR LED SCREEN CAPTURING 3 MORE LINES(VERTICALLY) THAN MY LED

This great , but how can you read from a Pic chip to see the info

How to set time format

Can we give power to the display directly from any other 5v power source instead of using the adapter?

How to turn inividiual pixels on

Great..., more helpfull to debuging my program and easy to understand program work.

Sir, how to change this to an off then on timer.? This is for my chicken house. I dont need the light in the starting.. only then on.. thanks

thank you soo much it worked 😁😁

Can we use same code for esp8266

In board wifi .....nodemcu is not showing

Hello. I would like to manage the LED matrix with the MAX7219 without using the library, that is, configure the MAX7219 and send the bits to, for example, turn on only one LED of the matrix, or an entire single column or row. . In the spi.write instruction it sends me an error that it is not valid to send an integer, but rather a string or array is required. Do you know how I can do it? Thank you.

Hello I need some help : to Programm ESP 32 and to use it to control a step motor with Pwm signal

nice

( .pioinit:13: Error is sourced command file:) what should i do