is it the same measurement for RTX 2070 gigabyte super windforce?

Did you forget to add front dust filter or is it just for video purposes?

Спасибо 🙏 😊

Hello, I see that you say in other comments that you have connected the ARGB of the 6 fans in a chain to a single ARGB connector on the board. In the video I only see you connect the 3 front ones to a fan connector but I don't see how you connect the top or rear fans. Do you also connect the 6 fans to a single fan1 connector to regulate by pwm or have you connected 3 to a fan1 port and another 3 to another fan 2 connector? I don't think it is good to connect all 6 fans to the same fan connector on the motherboard. Thank you and your channel is excellent

great vid, my 2070 super has the same problem, hotspot hits 105 degrees and fans spin up to 100%

Can someone help me , I can’t control the RGB and after I log in they turn off . I connected all things . I have a ASUS b550m

Mate, great video just did my 2080 TI following this, I swear it's cooler than it was brand new. So a big thank you for posting this. Clear and easy to follow.

Very nice video ! Can you put a list of all the parts you bought ?

Thanks for the video! I don't have thermal pads, only paste. Can I use it instead of the pads?

Hi, I recently bought the case and will build my PC soon. I once read that you have to hold the reset button for a few seconds and then you can probably get the RGB Control via the mainboard. A little late but maybe I could help if it works.

This is the same card I have and the same problem...thank you!

Thanks for the very helpful video! For the rightmost pad labeled 1.0 mm in the video I ended up going with a 1.5mm pad because I could see a clear light gap between the pad and components when shining a light from the bottom of the board after re-assembly. Guessing there could be some minor board to board variation. For folks replacing their pads, it may be worth spending a couple extra minutes to shine a light between the reassembled board to ensure the pads are touching all the components. The hot spot temps dropped by over 20 deg C for me! I'm thinking the old thermal paste was shot / almost all pumped out.

Hi Did this fix your issue, did you get appropriate heat from the air vents in the cabin after you replaced the heater exchanger?

How can it be that your power LED is flashing? As far as I know the Corsair 4000d has no hdd led.

Thank you :)

I had to undervolt this card and make a fan curve and yes before doing so I had also the 4000rpm fan like an airlplane taking off, the paste and pads being hold + the voltage being high by default makes this card a nightmare luckily I knew what to do

Thank you SO much for making this video! I was clueless on this process, had never taken apart a GPU before. My Gigabyte 2080 Super Windforce OC was suddenly sounding SO loud randomly. The fans were kicking in unbelievably loudly then going quiet and then loud and then quiet. It was infuriating. It used to always run quietly. I did this process using the GELID Ultimate thermal pads and Kryonaut thermal paste and my GPU is night-and-day different. In the same game/scene, my GPU temps have gone from 74-75 degrees down to 59-60. The fans are so much quieter, and my clock speed is far more high and stable. Thank you again for making this video, it really gave me the confidence to do this project!

How Many port ARGB in motheboard you have?

thank you! this was very helpful

tnks u🤗

i would like to see how you connect the controller. and if your cpu fan had also led it looks cool

I have been having this problem for years. At first I started using Msi Afterburner and using curve and under volting. However it’s not working anymore. I put my pc in the shop and he changed the thermal paste and replaced my motherboard, but I wonder if he changed the thermal padding? Thanks for the video. I haven’t even heard of thermal padding before this.

umm i have this card.. but mine has a small circuit board at the end with a wire that hooks to a thermal sensor that came off and I have no clue where the sensor is suppose to go. bad part is.. no one seems to have that small extra circuit on their windforce.. any ideas? (Your housing shows where the circuit would sit in the housing..but it does have that part.. (at 2:06) betweent the two screw hole mounts is a place a small circuit board can fit)

Do the backplate thermal pads need changing too?

I didnt get a remote with them, I can only change the presets with a button on my PC. Is there any software that I can still control them with? Or should I buy an rgb hub.

Great video, just followed this for my Gigabyte RTX2080Ti, and it worked perfectly. No more loud fans afterwards either! Had no idea that the thermal paste/pads can wear out. Thanks for making an easy to follow no frills video!

Just to make sure to do this repair I will need to order all 3 sizes 0.5mm 1.0mm 1.5mm and thermal paste correct?

Thanks! Going to build exactly the same next week helpfull as i am a beginner

Hello, tell me what kind of program for monitoring the PC system? Did you know that the video card also has thermal pads under the backplate?!

I've got a Gigabyte RTX 2080 WINDFORCE 8GB and been looking for info everywhere for pad thickness but it's all TI or GAMING OC that I've found. Have you any idea if it's the same as either of those cards? any help would be greatly appreciated. Thanks.

Great video! Lowered my temps from 86 Celsius to 60 Celsius. I changed the thermal pads and the paste as you instructed here. Easy to follow! One thing I noticed was the side close to the inputs had extra thermal pads. Just kept them the same as the other side. Also, the two screws you didn't take out had to be removed for me to get the other side off. Thanks again for this great video!!!

Good clean job, as a computer/laptop/VGA repair guy i used lots of MX-4 but switched to PTM7950 and Laird TPCM 7000 phase change pads because it lasts longer and has fenomenal heat transfer.

This is still a relevant card for 1080p and even 1440p if you do fps gaming and run the competition settings. Will run older games max settings easily.

can anyone help on of these torx screws got stripped what are they called as i need to replace, any help much appreciated.

Is loud this card?

One is CPU, the other one on which the thermal paste was replaced is what? The one that's is left as it is? What is it? And why you left it?

I recommend giving to the core Honeywell PTM7950 phase-change material, and instead of thermopads thermal putty Upsiren UX Pro Ultra and finally perform undervolting.

not the worst case its money well spent at that pricepoint. I like the Eclipse G300A or the Eclipse G360A more (they cost a bit more but they also have a better quality) also good options are the ENDORFY Signum 300 or the DeepCool CC560

Nice Upgrade!

Absolutely worth it also why is your table a cardboard box 😅

can you please tell me where did you connected the C-SW cable and the M-IN cable? 2:29 because mines dont work and im afraid i have to plug these ones somwhere not only the power because the switch doesnt change can you pls tell me i cant change the colour or speed the speed is very low for some reason does it affect that ive plugged the 4pin adaptor in 1 4pin socket in motherboard and every fan is connected to the adaptor cable thing

Hi guys, I changed my left headlight bulb the same way it worked for 2days and it was flickering and now the lights gone off again and dashboard has notification- left headlight dipped. Can anyone please help me with this thanks in advance

how's the wall mount after a year? is it still sturdy? any problems? I'm looking to purchase one soon

Thanks for the vid!

My A1 Has DLS and have replaced with D3S? are they compatible? Cant find any DLS replacements

can you replace the turning lights bulb?

ty for the video

9 months later , still happy with them ?

One of the most easy and amazing step by step video I have ever seen. Keep it up! Congrats!! :)

Hi, please could you tell me how long are those two arms. It would help me a lot!!!