Anyone wanting to know where the calculations are coming from search Google for ohms law while and it will have all the calculations for ohms and Watts law
@s0nt3k11 годин тому
The reason why the alarm didn't sound till you wear at 16.3 volts has to do with the components used in the inverter if the inverter is built with cheap components, it will have an accuracy of +/- 10% if it built with quality components they Will have an accuracy of +/- 5%
@s0nt3k11 годин тому
IMPORTANT - You should also note that you are using a pure sine wave inverter which is what household electronics are engineered for and the cheaper inverters are square wave And if you want to look up the science behind it, you're more than welcome. But basically your electronics will run hotter with a square wave that can create potential hazards and drastically shorten the life of your electronics.
@Bobsmith-yf9oy20 годин тому
What does it cost?
@jeffmarg1535День тому
How about on the DPU?
@UnderworldQДень тому
Why does the battery video make me cry?
@aripiameДень тому
Anche per il modello es400 ?
@Fatpumpumlovah2День тому
bad design.... main positive should be at the bigging of the pack and the negative at the end so that current flows thru the entire pack efficiently. In addition the more banks you make takes loads off every single bank so heat acutally goes down.
@marine1718День тому
Why 22v? Useless voltage
@chadclm2 дні тому
How much ready to go?
@jehugarcia2 дні тому
if you build it, $489 + Shipping ($50-$150) depending where you live. If we build it $500 + Shipping ($400-$500) depending on where you live
@Mad-Coo2 дні тому
Richie Aprile dealing 18650's now .....
@j-sonS2 дні тому
I like using your batterries to extend my bluetti and ecoflow items
@ShamilTLCVX2 дні тому
Балтун ты а не мастер!
@u2b832 дні тому
my fat ass gets 5-6 miles on 30 cells lol
@u2b832 дні тому
You just helped me revive a dead pack that was showing 3.7V on the main, simply by pushing that reset button! I had no idea it was there. In my case, charging on main and charge wires didn't fix it, but the reset did.
@HarmonyExpressSkoolie3 дні тому
I use Nissan Leaf Gen 1 cells in a 24V configuration in the Harmony Express. I used homemade bussbars (copper) on mine, but I'd love to have a 6s version of the PCB to match my system. It's difficult to find a 6S BMS as well.
@neilthomas87603 дні тому
How do I wake up my Riley rs2 battery
@erwingebka84623 дні тому
Hi these batteries fully charged are 4.2v .Whats the lovest voltage plesa
@Resurrectionaudio3 дні тому
Do these need a balancer
@user-gu2nu6pg6l4 дні тому
How to explain the code printed on the cell?Is there any information about the product date
@Aestdyfyfydyyetryuoiyfghcvb4 дні тому
LTO? LFP? or fire technology?
@cededavis15795 днів тому
Where at and how are they riced?
@piccolosan195 днів тому
I love riced batteries too
@mikeg12124 дні тому
What the heck is riced bateries?
@Danielebsir3 дні тому
He Ment Priced. lol 🤣
@thesayayin3655 днів тому
Will these buss bars work for 10 AH headway lithium cells ?
@jehugarcia5 днів тому
if cells are same diameter they should
@arishem5555 днів тому
DIY: how I lost my house cause of lithium batteries fire. This is all cool and exciting. But you don't wanna use it in everyday life or store within 20 meters from your home.
@ldohrnintenful5 днів тому
My alt charges at 14.5 volt, can I use this on my audio system in my car?
@jehugarcia5 днів тому
Yes
@ldohrnintenful5 днів тому
Good because I bought one last week. Thanks for the fast shipping here to chattanooga tn. Good looking out.
@ldohrnintenful5 днів тому
I've been told it's not recommended to run lithium with led acid so would you recommend deleting the lead acid under my hood and would it be okay to place this battery under the hood in its place?
@ldohrnintenful5 днів тому
Btw I've been following you for a while and I've defended your extensive knowledge in several audio groups. People will hate. You just keep being you and you'll keep being successful 💯
@handypaint295 днів тому
I’ll buy them from you?
@AbdAlgani19995 днів тому
thank you
@MarkPrince13175 днів тому
What type of cells are inside ?
@bobbear60065 днів тому
I plug in one power station into the other using the dc5521 output to dc5521input or XT60 input and charge the other using solar.
@Nilmoy6 днів тому
very long drawn out rambling with low speed of information conveyance. Good on the info, but wasting a lot of time.
@jaysolox6 днів тому
Whats the size for the nuts?
@sshaw44296 днів тому
The tube battery is also already in the “asinwheel U1” EBike.
@genecpu71316 днів тому
The case does not need to be destroyed. If you slice with an Exacto knife along the seem, this can be slowly opened. I have repaired my unit. I hope to create a video showing how and what component I replaced.
@renatosouzalider6 днів тому
Do you know how can i install a gps in my ES4?
@eunu69286 днів тому
How complicated is to put all P only in S?
@Shmade03046 днів тому
If I go to pcbway the file doesn’t show properly .. if I wanted to order them from pcb way am I doing something wrong
@jehugarcia6 днів тому
Click on the "Online Gerber Viewer" link
@Shmade03046 днів тому
@@jehugarcia I did it looks transparent and it looks like some parts are only highlighted doesn’t show the top layer or bottom layer
@jehugarcia6 днів тому
@@Shmade0304 might be your computer as it looks fine on mine
@jehugarcia6 днів тому
@@Shmade0304 you can also order them here www.ebay.com/itm/204740837955
@erikkovacs30977 днів тому
That utility transformer is sonewhere between 750-1000kva. The Tesla battery and inverter is there to smooth out the variable load from unpredictable charger usage. It will charge during light usage and discharge during peak usage. Not sure how big each inverter is. Im guessing about 1000kva judging from its physical size.
@MrUnclebuc17 днів тому
will this battery stand up to the Texas heat without catching fire ?