4 місяці тому
5 місяців тому
6 місяців тому
6 місяців тому
6 місяців тому
8 місяців тому
КОМЕНТАРІ
@ragibhasan8099 3 години тому
Bro can I upload another code for my BLE control car. Only change pinout
@jumbo999614 22 години тому
Just regular ink pen?
@aslamhossain1 18 годин тому
No. Permanent Marker
@fishsticks6611 День тому
The l298n motor driver beeps
@aslamhossain1 День тому
Increase the pwm value for speed.
@Unkn0wn_Reel День тому
Which one of 3V 6V or 12V N20 gear motor i should use??
@aslamhossain1 День тому
12v
@Unkn0wn_Reel День тому
@@aslamhossain1I'm using L298N motor driver. Is it okay to use 12V motor
@Unkn0wn_Reel День тому
Also if i didn't found 12V by any chance. Can i use 6V
@cesarpascalvasquez7499 День тому
Code?
@gamexpro2.040 День тому
When I connect with computer it's correctly pairing with mobile and getting signal in serial monitor But when i give power source then blutooth not pairing
@aslamhossain1 День тому
esp32 isn't getting enough power. Use buck converter and set voltage at 4.5v to power up the esp32
@gamexpro2.040 День тому
Can I give supply through esp 32 by charging cable???
@Thunder__Altaf 2 дні тому
I made all connections according to circuit diagram but, it's not working ,what might be the problem?
@aslamhossain1 День тому
Make sure enable pins of driver short with vcc
@SrujanV 2 дні тому
Bro then how to connect 8 sensor line follower connections to this circuit
@aslamhossain1 День тому
Connect sensor pin A0 to A7
@ShahFahadAhmed 2 дні тому
you could replace l298n that takes alot of space and weight, and use l293d ic or DRV8833 driver
@aslamhossain1 2 дні тому
Use tb6612fng
@islammabrouk848 2 дні тому
I need the code please
@cesarpascalvasquez7499 2 дні тому
Do you have a code to use a qtr sensor and don't need buttons?
@aslamhossain1 2 дні тому
I don't have
@benitocamelo8944 3 дні тому
why in the video is a esp 32 of 30 pins and in the diagram is a esp32 of 38 pin? it work with the one of 30?
@aslamhossain1 3 дні тому
Yes work
@himanshusingh4688 3 дні тому
can you please make a video on how to tune the kp and kd of lfr pid bot if it occurs different type of problems
@aslamhossain1 3 дні тому
𝐏𝐫𝐞𝐯𝐢𝐮𝐨𝐮𝐬 𝐓𝐮𝐭𝐨𝐫𝐢𝐚𝐥𝐬 𝐨𝐧 𝐒𝐨𝐜𝐜𝐞𝐫 𝐁𝐨𝐭: Robo Soccer Bot using Brushed ESC and FlySky Transmitter | How to Make Soccer Bot in Easiest Way: ukposts.info/have/v-deo/ppRehKSlpKSmkWg.htmlsi=gGmbe2CjW1lpm47K Robo Soccer Bot using FlySky FS-i6 Transmitter and BTS7960 Motor Driver: ukposts.info/have/v-deo/n6igeq2Zm6uFsJc.htmlsi=8B-Z586qo14An_A3
@himanshusingh4688 3 дні тому
sir what to do if my 5 array ir sensors give max value on white and min value on black
@aslamhossain1 3 дні тому
a little bit of change in digital conversion part: if (s[i] > threshold) s[i] = 0; else s[i] = 1;
@himanshusingh4688 3 дні тому
@@aslamhossain1 sir but i have done if(s(i)<threshold) s(i)=1 else s(i)=0 is this wrong ? my bot goes forward and always try to move to left and if i take it up and put down it goes in reverse direction
@HardeepSingh-zt4cd 4 дні тому
Kindly make same video using arduino uno board
@aslamhossain1 4 дні тому
Okay
@fatmatarek854 4 дні тому
I connected the circuit and it lights on when I connect the arduino with the laptop put when I remove it and turn on the switch it does not light on or move
@aslamhossain1 4 дні тому
Check all the connection. The problem is here
@Sadekul991 4 дні тому
Nahid broosss bot🤨
@aslamhossain1 4 дні тому
hae
@rlrentertainmentsinventions 4 дні тому
How many esc you have used
@aslamhossain1 4 дні тому
Details video: ukposts.info/have/v-deo/kHh9imqpi6x0q58.htmlsi=lRkaCqr9B9I3noPD
@rlrentertainmentsinventions 4 дні тому
@@aslamhossain1 seen it and subscribed
@ahbabmurshed2062 4 дні тому
From where did you buy those metal wheels?
@aslamhossain1 4 дні тому
www.daraz.com.bd/products/65mm-metal-wheel-rim-high-grip-rubber-tires-tyres-for-wltoys-144001-a959-a959-b-124019-124018-rc-car-partsred-i169884740.html
@ahbabmurshed2062 4 дні тому
@@aslamhossain1 thanks a lot.
@noorjannat7018 4 дні тому
All connections are correct but wheels are not moving and remote also shows Err-4%. What can I do?
@aslamhossain1 4 дні тому
Maybe the circuit is damaged
@user-rs9xo9zh4q 4 дні тому
Hey bro, can you share the code?
@aslamhossain1 4 дні тому
In the description
@noorjannat7018 4 дні тому
I have put an output volt of 5.01 in my XL4015 Buck Module. All setups were done. Then I connected the whole circuit to Lipo battery of 2200mah to check the movement. But nothing moved , also the VCC connected wire melted. Can u please say where is the problem? Is it the Output volt or wire?
@aslamhossain1 4 дні тому
Use thicker wire. 14-16 AWG
@noorjannat7018 4 дні тому
Thanks a lot, but now the problem is the two left wheels became auto. It Doesn't stop or move unless we disconnect the battery.
@noorjannat7018 5 днів тому
Can i use XL4015 as buck converter replacing LM2596? And if i do that, what and where will be the connections?
@aslamhossain1 5 днів тому
yes, you can use it. connect the battery terminal with the buck converter's input. set the output at 5v by adjusting potentiometer. then the output will go to BTS motor driver and Receiver.
@noorjannat7018 5 днів тому
After connecting the battery with buck converter LM2596 the blue light does not light up and also there is no voltage reading. What to do?
@aslamhossain1 5 днів тому
check the polarity.
@er.himanshu99 5 днів тому
Bro rotatory encoder is not required? So how are you using PID
@aslamhossain1 5 днів тому
Used push button.
@er.himanshu99 5 днів тому
@@aslamhossain1 my sensor analog readings are opposite max for white and min for black
@lgamer2324 7 днів тому
Online app link
@aslamhossain1 7 днів тому
www.amazon.in/Electronic-Spices-Control-Transmitter-Receiver/dp/B0BMF8C9T7
@aaryanyadav3567 7 днів тому
Can i use 2200 mah 3s lipo battery
@aslamhossain1 7 днів тому
Yes
@arjiesudaria6407 8 днів тому
Hello aslam, can i have the code and schematic?
@aslamhossain1 8 днів тому
ukposts.info/have/v-deo/i4Rpf5qOh4Or0Wg.htmlsi=4AJ8rax8NIbbinRZ
@arjiesudaria6407 7 днів тому
@@aslamhossain1 if i use 25ga what motor driver can i use? It says 25ga has a 2.1amps
@aslamhossain1 7 днів тому
@@arjiesudaria6407 l298n
@arjiesudaria6407 7 днів тому
@@aslamhossain1 can it support with this specification 12V 1:20 500RPM ≤190MA 460RPM ≤145MA 150gf.cm ≤2.1A 7.5kgf.cm
@aslamhossain1 7 днів тому
@@arjiesudaria6407 yes
@mazibarrahman8097 10 днів тому
If I use lipo battery, what will be the ampere and volt for this robot?
@aslamhossain1 9 днів тому
3s 3000/4000mAh
@bahadirgulcu272 10 днів тому
Good works
@bahadirgulcu272 10 днів тому
Super
@Hassan_STUDY 10 днів тому
Can you please share where we can find it?
@aslamhossain1 9 днів тому
tr.aliexpress.com/item/33022320164.html?spm=a2g0n.productlist.0.0.729ffcf9nngTsn&browser_id=ca9042ceadfb4fa1879abbc86810f898&aff_trace_key=f38c88aea65d4924ab8a7d581c441043-1707461356675-05219-UneMJZVf&aff_platform=msite&m_page_id=szsgncgghecawdxb18f43c42bd8360e32a2463137f&gclid=&pdp_npi=4%40dis%21BDT%21196.26%21108.55%21%21%211.79%210.99%21%402103266e17148288805051618ec09c%2167220518199%21sea%21BD%210%21AB&algo_pvid=726e27bd-3d8f-4f69-9f82-820d79ac3259
@mosaddikahoque8624 10 днів тому
I tried with 5 array IR but the button & motor are not working properly. Would you please tell me the reason?
@aslamhossain1 10 днів тому
Please follow this video for 5 array: ukposts.info/have/v-deo/eYZ2ZYeEZ4ySxGw.htmlsi=pysijxYS8412Gbvi
@noorjannat7018 10 днів тому
Which battery did you use?
@aslamhossain1 10 днів тому
Lithium-ion. Please Use LiPo Battery, which is suitable for soccer bot.
@MarlonVillaruel 11 днів тому
What is the purpose of pushbutton? Can I not put the pushbutton and direct it to the resistor and LED?
@aslamhossain1 11 днів тому
Push button to activate the line following code. You can ignore it.
@donzet4404 11 днів тому
How many rpm for the motor?
@aslamhossain1 11 днів тому
600
@fisimat 11 днів тому
Is the same of tutorial in your Chanel?
@ninetalesgamer6859 11 днів тому
Sir I am unable to unlock the code can anyone plz give me the code for this
@aslamhossain1 11 днів тому
Send a mail: [email protected]
@Madhan1110 12 днів тому
What to do if I have a maker-line IR array by cytron which gives digital readings, can we connect those to the arduino the same way
@aslamhossain1 12 днів тому
Yes. But need to change in code.
@Madhan1110 9 днів тому
Thank you so much for replying....❤️
@tiktokerist6989 13 днів тому
i love your works im from the Philippines and we are teaching robotics too can I use this as materials for teaching?
@aslamhossain1 13 днів тому
Sure
@arjiesudaria6407 14 днів тому
hello aslam, can you suggest motor that it's goods for line follower and sumobot the weight requirements is 1.5kg and 20x20cm
@aslamhossain1 14 днів тому
25ga gear motor
@arjiesudaria6407 14 днів тому
@@aslamhossain1 what speed?
@user-ni3es7xv1m 14 днів тому
Why this is a short video. You should give detail explanation with circuit.
@juansiahaan9737 14 днів тому
Sorry, I'd like to ask why the 220 Ohm resistor is connected to the GND pin of the combined GND of LM2596, XL6009, 4 push buttons, and 2 LEDs? What is the purpose of this?
@aslamhossain1 12 днів тому
Ground for all the devices is common.
@ninetalesgamer6859 15 днів тому
does this work for the width of 1.5 cma black tape
@aslamhossain1 12 днів тому
Sure
@suenildo 15 днів тому
Very good!!!! congratulations!!!
@aslamhossain1 15 днів тому
Thanks