Lose the safety guard and you will get the job done quicker and easier

Don't they sell these corners?

Why do people even bother making videos if theyre too afraid to talk. Also none of these are "tricks"

głupie niemiłosiernie. zamiast mieć pełną blachę z góry teraz ma dziurę w którą pięknie wpływa woda z deszczu (i wszystkie śmieci)

How do I get funk fpv to review this?

Don't be as stupid as this guy who knows nothing. Never weld anything that is either galvanised nor zinc plated. The gas produced will kill you .

The things I think he intended to show were to use a thin kerf blade for cutting vs the thicker ones which are for grinding. and when cutting your blade will last longer depending on the direction. It should cut so it rotating on the surface towards the gradual edge and not just the sharp edge which tears up the disc real fast.

Great

ALWAY! Clean the galvanising off before welding, with this method of welding with the zinc in place you will not live long enough to see it fail.

일시키는사장님들은 참 힘들겠습니다

이것도실력이라고 ㅉ

This is just a waist of tine any DIWyer with any sense knows this

Poor instructions… this video is missing a lot explanation

اسلام عليكم انا عندي غرفه فطابق اثاني والدرجات لاصقه فبعضها كيف اسوي درج نضامي

О человек учил Геометрию Вот без него ЯБ не знал Как оно надо. Ну для на читающий там на видео куча проблем.

That's not a pipe secret, that's geometry. It has nothing to do with how pipes are made or what out of or their features. A pipe being a tube is not a secret.

The fact that people subscribe to this is absolutely amazing.

да не будет ни один нормальный сварщик такой хернёй заниматься

i salute you sir!

Where is the trick? 🤬🤬🤬

Респект чувак.

うますぎる❤バチバチだけが全てでない😂

Talk too much

Throw the 4.5" away and get a 6 inch Metabo

Could have saved yourself a great deal of effort by just making a pair of 45d cuts on each pipe with a circular or band saw. Cut once at 45d, rotate the pipe 90d and make another 45d cut. It will get you to the exact same place without all the extra pen and paper work.

That was really cool

Who did not know that every body does one thing you did wrong always cut on the outside of the line not down the middle. Good job

Muito bem ensinado mas eu so uso com o segundo punho assim trabalho com as duas maos 👍

Y ese no sabe que existen las uniones triples de 90°, rápido y fácil

literally just e 90 degree angles on the pipes and weld it together didnt even have to watch the video i have never even used a welding torch its just common sense

Обычная эксплуатация шлиф машины, все это можно прочесть в инструкции к аппарату и в чем тут такого важного я не понимаю.?

No tricks were shown, this is just how to use a grinder.

Why would anyone make this junction this way? Six dots with a Sharpie, a chop saw, and about 90 seconds will get the same result.

Eccellente

I came in the end.

Damn. Just eyeball it.

"Мало кто знает" - конечно, если в школе забить на элементарную тригонометрию, это будет удивительным секретом. Ну, собственно, примерно такие в сварщики и прочие грузчики и идут

Right 👍

These fucking tack welding videos really piss me off

In comment section, no one complains like welders do.

This is professional welding

Speak

Děkuji za video! A jedná se o rutilové elektrody nebo bazické? Podle toho jak snadno zapalujete oblouk, tak tipuji rutilové. Děkuji.

what kinda geometry magic just unfolded before my eye's ?!

Good video, bad grinder safety

Content is more than I learnt in arc welding short course, Electrical engineering as well !!! Thanks for sharing the content !!! Cotinue, add oil ! 4 May.

Пото му что они такие же как ты , не хрена не говорят

Please delete this your clip and redo it again but! This Rhine show the unplugging the cord from the wall or removing the battery from the machine. Because innocent person if it’s first time going to use this dangerous tool and not known to unplug or removing the battery they easily will cut their 3-4 fingers in a matter of 1 or 2 seconds. Please delete it & redo it. Thank you

Why pipe clamps are used at construction sites

Point of gloves that let your finger poke through? No idea.